D-Link DIR-130 - Broadband VPN Router Guía de configuración

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 1of 10

How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV

This setup example uses the following network settings:

In our example the IPSec VPN tunnel is established between two LANs: 192.168.0.x and

192.168.1.x.

NOTE: It is essential to have private networks (LAN 1 and LAN 2) on different subnets.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 2of 10

Configuration of the DIR-130

Step 1. Log into the DIR-130 by opening Internet Explorer and typing the LAN address of the

device. In our example we are using the default 192.168.0.1. Enter Username and Password

which you specified during the initial setup of the Firewall.

Step 2: Click on SETUP, select VPN SETTINGS, and select IPSec from the ADD VPN

PROFILE dropdown list and click Add.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 3of 10

Step 3: Configure the IPSec VPN as followed:

IPSEC SETTING

•Enable: check box to enable

•Name: enter a name for the VPN

•Encapsulation Mode:: Tunnel

•Remote IP: select Site to Site and enter the remote gateway

•Remote Local LAN Net /Mask: enter the remote network and remote subnet mask

Authentication: enter a Pre-shared Key (Pre-share key must match remote side)

PHASE 1

•IKE Proposal List: leave at default (3DES, SHA1)

PHASE 2

•IPSec Proposal List: leave at default (3DES, SHA1)

Click Save Settings.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 4of 10

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 5of 10

Configuration of DI804HV/808HV

Step 1: Open your web browser and type in the IP address of the router (192.168.0.1 by

default). Enter the username (admin by default) and password (blank by default), and then

click OK.

In our setup we changed the IP of the unit to 192.168.1.1 (NOTE both routers can not be

on the same subnet).

Step 2: Click on the Home tab and select the VPN button and configure as followed:

•VPN: check to enable

•Max. number of tunnels: enter the number of tunnels

ID 1

•Tunnel Name: enter a name of the VPN

•Method: select IKE

Click Apply to save the settings.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 6of 10

Step 3: Click on More under Method and configure as followed:

Tunnel Name: the name of the tunnel should already be entered if done in the previous step

•Local Subnet: enter the local subnet (192.168.0.0 in this example)

•Local Netmask: enter the local subnet mask(255.255.255.0 in this example)

•Remote Subnet: enter the remote subnet (192.168.1.0 in this example)

•Remote Netmask: enter the remote subnet mask(255.255.255.0 in this example)

•Remote Gateway: enter the remote gateway (172.68.140.140 in this example)

•IKE Keep Alive (Ping IP Address): enter an IP address of a client on the remote side

(192.168.1.100 in this example)

•Preshare Key: enter preshare key as desired (Pre-share key must match remote side)

•IPSec NAT Traversal: check to enable

•Auto-reconnect: check to enable

Click Apply to save the settings and click Continue when prompted.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 7of 10

Step 4: Click on Select IKE Proposal and configure as followed:

•Proposal Name: enter a name for the Proposal ID Number 1

•DH Group: Group 2

•Encrypt algorithm: 3DES

•Authentication Algorithm: SHA1

•Life Time: 28800

•Life Time Unit: Sec

•Proposal ID: select 1and click on Add To to add to the IKE Proposal index

Click Apply and then click Back.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 8of 10

Step 5: Click on Select IPSec Proposal and configure as followed:

•Proposal Name: enter a name for Proposal ID Number 1

•DH Group: Group 2

•Encapsulation Protocol: ESP

•Encryption Algorithm: 3DES

•Authentication Algorithm: SHA1

•Life Time: 3600

•Life Time Unit: Sec.

•Proposal ID: select 1and click on Add To to add to the IPSec Proposal index

Click Apply and then click Continue when prompted.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 9of 10

Step 6: Click on the Status tab and select the VPN Status button. The VPN should be

established. If the tunnel has not been established, click on the Refresh button or ping to an

IP address on the remote side. When replies are sent back, the tunnel has been established.

D-Link Technical Support – How to setup an IPSec VPN connection between a DIR-130 and DI-80xHV Page 10 of 10

Connecting to shared resources via VPN

To connect to shared resources via VPN you can map remote computers’ drives and folders

by opening Windows Explorer and going to Tools > Map Network Drive (you need to specify

the IP address of the computer on remote network and the name of the shared folder):

Alternatively you can do Search > Computers or People > Computer on Network > specify the

IP address of the computer you are trying to connect to.

If you do not see computers in My Network Places or My Network Neighbourhood you may

need to enable NetBIOS over TCP/IP in Windows.

Note that firewall/antivirus software installed on your or remote computer may stop you from

accessing remote network.

Otros manuales para DIR-130 - Broadband VPN Router

Tabla de contenidos

Otros manuales de Enrutador de red de D-Link

D-Link

D-Link DSL-G255 Manual de usuario

D-Link

D-Link DIR-615S Manual de usuario

D-Link

D-Link DIR-814 Manual de usuario

D-Link

D-Link DES-1008FX Manual de usuario

D-Link

D-Link DSL-2642B Manual de usuario

D-Link

D-Link DSL-2540T Manual de usuario

D-Link

D-Link Xtreme N L7-N-R2000 Manual de usuario

D-Link

D-Link DSL-G804V Manual del propietario

D-Link

D-Link DSL-2640U Manual de usuario

D-Link

D-Link DIR-855L Manual de usuario

D-Link

D-Link DES-3528 - xStack Switch - Stackable Manual

D-Link

D-Link DIR-820 Manual de usuario

D-Link

D-Link DES-802 - Switch Manual de usuario

D-Link

D-Link DGS-1016D - Switch Manual de usuario

D-Link

D-Link N300 Manual de usuario

D-Link

D-Link DSL-224 Manual de usuario

D-Link

D-Link DIR-605L Manual de usuario

D-Link

D-Link DES-7200 Manual de usuario

D-Link

D-Link AC1200 Manual de usuario

D-Link

D-Link DSL-2520U Manual de usuario

D-Link

D-Link DI-634M Manual de usuario

D-Link

D-Link DIR-2680 Manual de usuario

D-Link

D-Link DES-1016E Manual de usuario

D-Link

D-Link DWP-1010KT Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad