D-CUT TC-330 Manual de usuario

OPERATION MANUAL

D-CUT Flooring / Trim Cutter TC-330

www.dcutproducts.com

SAFETY RULES FOR THE FLOORING CUTTER

1. READ AND UNDERSTAND THIS INSTRUCTION MANUAL BEFORE

OPERATING THE D-Cut MULTI-FLOORING CUTTERS.

2. If you are not thoroughly familiar with the operation of D-Cut Multi-flooring

Cutter, obtain advice from a qualified instructor or call 630-916-9100 USA

3. Stay alert. Do not operate while under the influence of drugs, alcohol, or

medication.

4. Always wear safety approved eye protection with side shields(ANSI Z87.1)

5. Keep work area free of debris.

6. Keep children and unauthorized persons away from the D-Cut Multi-flooring

Cutter and work area.

7. Make sure tool is secure. Operate only on a firm substrate or solid stand.

8. Use the right tool. Do not force the D-Cut Multi-flooring Cutter or use it for a

job for which it was not designed; use only on approved materials.

9. Keep the blade sharp. A dull blade will not perform properly.

10. Always keep hands away from blade while operating or carrying the cutter.

11. Do not alter or misuse this tool. The D-Cut Multi-flooring Cutter is precision

built; modifications not specified in this manual may result in a dangerous

and unsafe environment.

12. Maintain the D-Cut Multi-flooring Cutter with care. Keep Blade sharp and

clean. Follow instructions for changing accessories.

13. Use only recommended accessories. The use of improper accessories may be

hazardous and cause injuries.

14. Never leave the D-Cut Multi-flooring Cutter unattended. Keep the cutting

head in a close position with lock pins when the cutter is not in use.

CUTTING AND C

Installation of t

utter

(1)

Install the handle assembly to

the cutter base as shown.

Warning: Do not put your

fingers against the sharp edge

of the blade

any time.

Angle

Cut

Position the guide bar at 45°.

Insert a baseboard or a shoe

mold between the cutting

blade and the base, flush with

the guide bar as shown, then

pull the handle down to

complete a cut.

Straight

Cut

Insert the floor plank between

the cutting blade and the base,

flush with the guide bar on the

working table, hold the plank

and pull handle down to

complete a cut.

Bevel

Cut

(1)

Make a straight cut on a

workpiece to your

measurement and then pull

the knob as pointed by an

arrow, adjust the cutter head

to your desired angle. Pull

out the handle from the base

to change the handle

position on the cutting head.

Bevel

Cut

(2)

Insert the workpiece between

the cutting blade and flush the

working table with the guide

bar, and stop the edge of the

workpiece from previous

straight cut at the cutting base

where you can see and feel it

while you're moving along the

workpiece, hold the workpiece

firmly, and then pull the handle

down to complete a cut.

Changing t

Blade

Use provided Allen wrench

to Loosen the five screws as

shown, the blade by each

end and carefully move the

blade out of blade holder.

Note: the flat side of the

blade should face the

working table.

Warning: Do not put your

fingers against the sharp

edge of the blade at any

time.

Lock

Cutt

ing

Head

Use the provided Lock Pin to

tuck the hole on the main

column as shown. Make sure

the cutting blade is in a close

position when the cutter is not

in use.

Transport

Once the lock pins firmly

locked the cutting head and

pull out the handle to carry the

cutter as shown.

Changing t

Nylon

Bar

Use provided Allen wrench to

Loosen the five screws, then

carefully move nylon bar out of

the nylon bar holder.

Note: the flat side of the blade

should face the working table.

Warning: Do not put your

fingers against the sharp edge of

the blade at any time.

Explosive View

Parts Q’ty

Wheel 2 34

Screw M6X20 4

Screw 1 35

Handle Base 4

Sleeve 2 36

Bolt M12X95 2

Washer 10 2 37

Screw M8 B 1

Screw M8 X14 2 38

Screw M8 C 1

Screw M5 X 12 17 39

Handle A 1

Rectangular Tube 1 40

Handle Base 1

Nylon Bar 1 41

Nut M4 2

Nylon Bar Holder 1 42

left ABS handle 1

Washer 5 6 43

Right ABS handle 1

Guide Sleeve 2 44

Screw M4X30 2

Spring Washer 8 2 45

Screw M4X20 1

Screw M8X16 2 46

Rubber Feet 2

Locker Nut M5 3 47

Washer 5 4

Slide Pathway 1 48

Cutter Base 1

Bolt M8X16 4 49

Lock Pin 1

Nut M5 1 50

Screw M4X10 2

Left Rotation Plate 1 51

Lock Pin Base 1

Spring 2 52

Shaft 4

Screw M5X16 13 53

Locker Nut M12X1.5 2

God 2 54

Washer 12 2

Working Table 1 55

Right Rotation Plate 1

Guide Bar 1 56

Locker Nut M10 2

M8 Screw A 1 57

Knurled Angle Knob 2

Screw M6X12 5 58

Tension Spring 2

Blade 1 59

Left Angle Position Shaft 1

Locker Nut M12 2 60

Screw M8 X16 2

Blade Holder 1 61

Bearing 1

Nylon Cam Ring 4 62

Locker Nut M8 2

Eccentric Cam Bracket 2 63

Slider 1

Shaft 2 64

Locker Nut M6 1

Special Screw 2 65

Screw M6 X10 2

Aluminum Eccentric Cam 1 66

Left Angle Position Shaft 1

Explosive View

Otros manuales de Cortador de D-CUT

D-CUT

D-CUT MH-510 Manual de usuario

D-CUT

D-CUT HC-040 Manual de usuario

D-CUT

D-CUT MD-230 Manual de usuario

D-CUT

D-CUT LX-230 Manual de usuario

D-CUT

D-CUT LX-340 Manual de usuario

D-CUT

D-CUT TC-100 Manual de usuario

D-CUT

D-CUT GC-230 Manual de usuario

D-CUT

D-CUT MD-460 Manual de usuario

D-CUT

D-CUT SC-620 Manual de usuario

D-CUT

D-CUT LT-180 Manual de usuario

D-CUT

D-CUT AK-360 Manual de usuario

D-CUT

D-CUT XP-215 Manual de usuario

D-CUT

D-CUT LP-650 Manual de usuario

D-CUT

D-CUT LX-200 Manual de usuario

D-CUT

D-CUT DP-340 Manual de usuario

D-CUT

D-CUT RC-200 Manual de usuario

D-CUT

D-CUT MD-330 Manual de usuario

D-CUT

D-CUT LT-200 Manual de usuario

D-CUT

D-CUT PL-215 Manual de usuario

D-CUT

D-CUT LU-215 Manual de usuario

D-CUT

D-CUT MD-630 Manual de usuario

D-CUT

D-CUT MH-330 Manual de usuario

D-CUT

D-CUT LT-330 Manual de usuario

D-CUT

D-CUT LH-320 Manual de usuario

Manuales populares de Cortador de otras marcas

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manual de usuario

Makita

Makita DCS552 Manual de usuario

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manual de usuario

Makita

Makita 4112HS Manual de usuario

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manual de usuario

Hitachi

Hitachi CM 4SB2 Guía de solución de problemas

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manual de usuario

GCC Technologies

GCC Technologies AFJ-24S Manual de usuario

DeWalt

DeWalt XR LI-ION DCS350N Manual de usuario

Baudat

Baudat ES1 Manual de usuario

Mafell

Mafell ZAF 200 Guía

Makita

Makita 4100NH Manual de usuario

Formax

Formax FD 574 Manual de usuario

EINHELL

EINHELL TE-MA 1500 Manual de usuario

Husqvarna

Husqvarna Cut-n-Break K 760 Manual de usuario

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manual de usuario

TRI tool

TRI tool 301A Manual de usuario

Roller

Roller King 1 1/4 Manual de usuario