CYP DCT-39 Manual de usuario
DCT-39
Compact Digital Audio Processor with De-pop,
Volume Adjustment and SRC Functions
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2015 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE
VR0 16/10/15 Preliminary release
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front and Rear Panels .....................3
6.2 Top Panel ..........................................4
6.3 Side Panel .........................................5
7. Connection Diagram ............................ 6
8. Specications ........................................ 7
9. Acronyms ............................................... 8
1
1. INTRODUCTION
The digital audio processor is designed to allow optical or coaxial
LPCM audio source input and convert to different sampling rates
up to 192kHz/24bits. The digital audio processor utilizes DSP engine
instead of software process to prevent distortion. The converted audio
source signal could be output to both optical and coaxial audio
signals simultaneously. The outputs can be connected with amplier
for high quality audio output. Besides, the audio processor support
DSD over PCM (DOP) decodes to PCM in order to further process
the audio signal not only for sampling rate convert but also volume
control. Meanwhile, the pop noise could be reduced when plug in
audio source.
2. APPLICATIONS
• Professional music player
• Amplier producer
• Audio equipment manufacturer
• Studio
3. PACKAGE CONTENTS
• 1×Digital Audio Processor Main Unit
• 1×5 V/2.6 A Power Adaptor
• 1×Operation Manual
4. SYSTEM REQUIREMENTS
Input audio coaxial or optical audio source and output to amplier.
2
5. FEATURES
• Supports coaxial and optical digital audio input
• Supports Non-LPCM pass through
• Supports coaxial and optical audio output simultaneously
• Supports LPCM input sampling rates up to 192kHz
• Supports to convert sampling rate of input audio source. The
maximum sampling rate up to 192kHz/24 bits
• De-pop function to eliminate pop sound once plug in audio source
• Supports volume control, the minimum volume control could be
reduced to -60dB
• Supports DOP decode to PCM of coaxial and optical audio source
• Supports rmware update via micro USB
• Compact and light weight design
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front and Rear Panels
COAX IN OPTI. IN
DC
5V
SERVICE
OPTI. OUT COAX OUT
Front
1 2 3
Rear
4 5 6
1COAX IN: Connects the coaxial audio source. Just plug in coaxial
audio source here.
2OPTI. IN: Connects the optical audio source. Just plug in optical
audio source here.
3DC 5V: Connects adaptor of DC 5V to power on the device.
4SERVICE: Support rmware update in eld and supply power to
device instead of power adaptor.
5OPTI. OUT: For optical audio output such as amplier.
6COAX OUT: For coaxial audio output such as speaker.
4
6.2 Top Panel
BYPASS
192
176.4
96
88.2
48
44.1
FS.
(kHz)
0
VOL.
(dB)
-15
-30
-60
COAX
VOL.
2
1
3
4
5
1VOL. (dB) LEDs: Volume indicator shows the volume from 0 , -15, -30
and -60 dB.
2FS. (kHz) LEDs: Audio frequency indictor of 192, 176.4 , 96 , 88.2 , 48,
44.1 kHz.
3BYPASS LED: Bypass indicator will illuminate when switches device
to “Output Sample Frequency Mode” and no need to convert the
input audio source to different sampling rate.
4COAX LED: Coaxial indicator will illuminate once connects with
coaxial audio source. The indicator will not illuminate when
connects with optical source.
5VOL. LED: Volume indicator will illuminate once selects to “VOL
mode”.
5
6.3 Side Panel
FUNC. IN
-
+
1 2 3
1FUNC: Function key provides modes selections. There are three
modes available.
a. Volume Mode: The default setting sets at volume mode. The
volume could be adjusted once under this mode and the VOL
indicator will illuminate. The mode will automatically switch
back to this mode once switches to input sampling frequency
mode or output sampling frequency mode after four seconds
and not active them.
b. Input Sampling Frequency Detection Mode: The sampling rate
of input audio source will be automatically identied under this
mode. The frequency indicator will ash for input sampling rate
accordingly. If no audio source input, the frequency indicator
will not illuminate.
c. Output Sampling Frequency Adjust Mode: This mode offer input
audio source converts to different output frequencies of 44.1,
48, 88.1, 96,176.4 and 192kHz. If the frequency no needs to
convert, please select “Bypass”.
2IN: The default setting sets at “coaxial in” for input audio source. If
input audio source is optical audio source, please press “IN” key to
switch it.
3MINUS/PLUS (-/+): To adjust output volume from 0~-60dB or select
in different frequencies.
6
7. CONNECTION DIAGRAM
COAX IN OPTI. IN
DC
5V
SERVICE
OPTI. OUT COAX OUT
DVD or Blu-ray Player
AV Receiver and Speakers
Power Supply
Digital Coaxial
Audio Input
Digital Coaxial
Audio Output
Digital Optical
Audio Input
Digital Optical
Audio Output
Tabla de contenidos
Otros manuales de Convertidor de medios de CYP
CYP
CYP PU-160ETH Manual de usuario
CYP
CYP CSC-1600HD Manual de usuario
CYP
CYP CPLUS-SDI2H-W CPLUS-SDI2H Manual de usuario
CYP
CYP SY-P290 Manual de usuario
CYP
CYP CP-VSRGB Manual de usuario
CYP
CYP QU-8MS Manual de usuario
CYP
CYP CS-802D Manual de usuario
CYP
CYP CS-801H Manual de usuario
CYP
CYP DCT-4 Manual de usuario
CYP
CYP DCT-1D Manual de usuario
CYP
CYP CLUX-SDI2HS Manual de usuario
CYP
CYP AU-D9 Manual de usuario
CYP
CYP CM-397M Manual de usuario
CYP
CYP VHC-1 Manual de usuario
CYP
CYP DCT-2 Manual de usuario
CYP
CYP DCT-9DD Manual de usuario
CYP
CYP CPT-386 Manual de usuario
CYP
CYP CPLUS-V10E Manual de usuario
CYP
CYP CP-280H Manual de usuario
CYP
CYP SY-12H-4K22 Manual de instalación
