CYP CP-255I Manual de usuario

CV/SV/PC/HD/HDMI

1080p Scaler Box

CP-255I

Operation Manual

TABLE OF CONTENTS

1. Introduction..........................................................................................

2. Features................................................................................................

3. Package Contents..............................................................................

4. Operation Controls and Functions....................................................

4.1 Front Panel.....................................................................................

4.2 Rear Panel.....................................................................................

4.3 OSD Operation..............................................................................

4.4 Remote Control.............................................................................

5. Specications.......................................................................................

5.1 General Speciﬁcation..................................................................

5.2 Support Resolution........................................................................

6. Connection and Installation..............................................................

1. Introduction

Cypress's CP-255I Scaler Box is designed to upscale digital/analog

video signal from Composite, S-Video, PC, Component (HD) and HDMI input

sources, to digital HDMI output of wide-range HDTV and PC resolutions, up

to 1080p and WUXGA (1920 x 1200.) Besides video upscaling, the scaler

box also converts digital/analog audio signal to digital format, then output

either through HDMI combining with the video, or Coaxial S/PDIF separately.

Cypress CP-255I has a comprehensive OSD menu that allows user to select a

variety of output resolutions and adjust for best picture quality.

2. Features

1. HDMI 1.2, HDCP 1.1 and DVI 1.0 compliant.

2. Scales any PC (VGA ~ WUXGA) /HD (480i ~ 1080p) resolutions to/from

another PC/HD resolutions.

3. Automatically detect the factory setting of the connected display and

output the corresponding resolution and refresh rate, when the NATIVE

output is selected.

4. Supports 50/60Hz frame rate conversion.

5. Supports 3-D motion video adaptive, 3-D de-interlacing, and 3:2 / 2:2 pull-

down detection and recovery.

6. Provides output picture adjustment on contrast, brightness, hue, saturation,

sharpness, RGB (color tone) level, and aspect ratio size.

7. Supports high resolution input/output:

PC: VGA, SVGA, XGA, SXGA, UXGA, WXGA, WSXGA, WUXGA

HDTV: 480i, 576i, 480p, 576p, 720p, 1080i, and 1080p

8. Supports digital and analog audio input and output.

3. Package Contents

1. Cypress CP-255I Scaler Box

2. 5VDC Power Supply Adaptor

3. Operation Manual

4. Operation Controls and Functions

4.1. Front Panel

1. POWER Button and LED Indicator:

Press the button to turn ON/OFF the power of the unit. The LED will

illuminate when the power is turned on.

2. IR remote control sensor.

3. Input Selection Buttons and LED Indicators:

Press each of the buttons (CV/SV/COMP/PC/HDMI) to select the

desired input source. The LED will illuminate when the corresponding

input is selected.

4. MENU Button:

Press the MENU button to bring up OSD operation menu (see section

“4.3 OSD Operation”for reference.)

5. +/- Buttons:

a. On the ﬁrst tier of OSD menu, use + and - buttons to move up/down

the highlight item for selection.

b. Once the desired option is selected, use + and - buttons to toggle

between setting values.

6. ENTER Button:

In OSD menu, use the ENTER button to conﬁrm the selection.

POWER CV SV COMP PC

MENU ENTER

Digital Video Scaler Processor

HDMI

1 2 3 4 5 6

4.2. Rear Panel

HDMI OUT

AUX IN RS-232 PC IN

HDMI IN

PC IN

Cr/Pr

Cb/Pb

CO-AX

LCV

DC 5V

L SV

CO-AX OUT

3 5 6 8 9

4 7

1. HDMI OUT and CO-AX OUT:

Connect the HDMI OUT port to the HDMI input port of your display such

as HDTV. Connect the CO-AX OUT port to the Coaxial (S/PDIF) input

port of your ampliﬁer for separate digital audio output.

2. AUX IN Input:

When the video signal input through the HDMI IN port is from a DVI

source such as a PC, use the AUX IN port to input the audio signal.

3. HDMI IN Input:

Connect the HDMI IN port to the HDMI output port of your source

equipment such as DVD player or Set-Top-Box. Or, use HDMI to DVI

cable to connect to the DVI output of your PC.

4. RS-232:

The port is for ﬁrmware update only.

5. PC IN for Video and Audio Input:

Connect the PC IN D-Sub (15-pin) port to the D-Sub output port of your

PC. And, connect the PC IN 3.5mm phone jack to the audio output

port of your PC.

6. Y Pb/Cb Pr/Cr Video and L/R Audio Input:

Connect the Y Pb/Cb Pr/Cr (Component) 3 RCA input ports to the

Component output port of your video source equipment such as DVD

player or Set-Top-Box. And, connect the L/R audio input ports to the

audio output port of your audio source equipment.

7. CO-AX Input:

The CO-AX port provides the digital audio input support, and can be

used to combine with each video input signals from CV/SV/COMP/PC/

HDMI ports. Once connected, please use the Audio Source Selection

in the OSD menu to select between Coaxial (S/PDIF) or other audio

source (see section “4.3 OSD Operation”for reference.)

8. Composite Video / S-Video and L/R Audio Input:

Connect the Composite or S-Video input port to the Composite or

S-Video output port of your video source equipment such as DVD

player or Set-Top-Box. And, connect the L/R audio input ports to the

audio output port of your audio source equipment.

9. Power:

Plug the 5VDC power supply into the unit and connect the adaptor to

AC wall outlet.

1st Tier Option 2nd Tier Option Adjustment

VIDEO - PICTURE MODE USER / STANDARD / VIVID / MOVIE

- CONTRAST 0 ~ 100 of Contrast Level

- BRIGHTNESS 0 ~ 100 of Brightness Level

- HUE 0 ~ 100 of Hue Level

- SATURATION 0 ~ 100 of Saturation Level

- SHARPNESS 0 ~ 100 of Sharpness Level

- SCALE OVERSCAN / UNDERSCAN /

LETTERBOX / PANSCAN / FULL

- NR LOW / MIDDLE / HIGH / OFF

- EXIT Back to the 1st Tier

COLOR - COLOR TONE USER / NORMAL / WARM / COOL

- RED 0 ~ 100 of Red Color Level

- GREEN 0 ~ 100 of Green Color Level

- BLUE 0 ~ 100 of Blue Color Level

- EXIT Back to the 1st Tier

OUTPUT -

NATIVE / VGA / SVGA / XGA / SXGA

/UXGA / 480i / 480p / 720p@60Hz

/ 1080i@60Hz / 1080p@60Hz / 576i

/ 576p / 720p@50Hz / 1080i@50Hz

/ 1080p@50Hz / WXGA / WSXGA /

WUXGA

OSD

- HPOSITION 0 ~ 100 of OSD Horizontal Position

- VPOSITION 0 ~ 100 of OSD Vertical Position

- TIMER 0 ~ 100 of OSD Show Time (sec.)

- TRANSP 0 ~ 100 of OSD Transparent Level

- EXIT Back to the 1st Tier

AUDIO - SOURCE HDMI / L/R / COAXIAL

- DELAY OFF / 40MS / 110MS / 150 MS

- SOUND ON / MUTE

- EXIT Back to the 1st Tier

INFORMATION -

SOURCE (Input interface)

INPUT (Input Resolution)

OUTPUT (Output Resolution)

VERSION (Firmware Version)

EXIT - Close the OSD Menu

4.3. OSD Operation

4.4. Remote Control

1. POWER:

Press the button once to power on the CP-255I.

Press again to enter standby mode.

2. INPUT:

Press the button repeatedly to toggle through

various input sources.

3. HD Input:

Press the button to directly select component

input.

4. PC Input:

Press the button to directly select PC input.

5. HDMI/DVI Input:

Press the button to directly select DVI (or HDMI)

input.

6. Output Resolution:

Press any one of the button to directly select

output resolution. For other output resolutions that

are not covered by these buttons please enter

OSD Menu to select them.

7. MENU:

Press the button to bring up OSD main menu page.

8. Exit:

Press the button to exit from a sub menu or main

menu.

9. Up/Down/Left/Right:

Press the Up/Down button to move the highlight

bar to your desired parameter during the

OSD operation. Press the Left/Right button to

increase/decrease the setting value of a selected

parameter.

10. OK (Enter):

Press the button to conﬁrm your selection.

11. Reset:

Press the button to reset the unit's ﬁrmware setting

to the factory default value.

12. Auto Adjust:

Press the button to optimize the position of the

picture (picture centering) on the screen.

5. Specications

5.1. General Specication

* Frequency bandwidth: 1.65Gbps (single link)

* Input Ports:

Composite x 1 / L/R x 1

S-Video x 1 / L/R x 1

Component (3 RCA) x 1 / L/R x 1

PC D-Sub (15-pin) x 1 / 3.5mm Phone Jack x 1

HDMI x 1 / 3.5mm Phone Jack x 1 (for DVI)

Coaxial (S/PDIF) x 1

* Output Ports:

HDMI x 1

Coaxial (S/PDIF) x 1

* 5V DC power supply

* Dimensions: 215(W) x 154(D) x 47(H)mm

* Weight: 1Kgs

5.2. Support Resolution

INPUT

VGA@(60/72/75/85Hz),

SVGA@(56/60/72/75/85Hz),

XGA@(60/70/75/85Hz),

SXGA@(60/75/85Hz), UXGA@60Hz,

WXGA@60Hz, WSXGA@60Hz, WUXGA@60Hz

TV 480i, 480p, 576i, 576p, 720p@(50/60Hz), 1080i@(25/30Hz),

1080p@(50/60Hz)

OUTPUT

VGA@(60/72/75/85Hz),

SVGA@(56/60/72/75/85Hz),

XGA@(60/70/75/85Hz),

SXGA@(60/75/85Hz), UXGA@60Hz,

WXGA@60Hz, WSXGA@60Hz, WUXGA@60Hz

TV 480i, 480p, 576i, 576p, 720p@(50/60Hz), 1080i@(25/30Hz),

1080p@(50/60Hz)

6. Connection and Installation

HDMI

Cable

HDMI

PC-inComponentS-VideoComposite

Otros manuales para CP-255I

Tabla de contenidos

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario

Expert

Expert EX-9543 Manual de usuario