CYP CDPS-CS6 Manual de usuario
CDPS-CS6
Auxiliary Control System
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2016 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 07/01/16 Preliminary Release
RDV2 21/04/16 Add WebGUI
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel.........................................4
6.3 IR Pin Denition .................................5
6.4 RS-232/Telnet Command List ..........6
6.5 Software Application.......................8
6.6 Telnet Control ...................................9
6.7 WebGUI Control .............................11
7. Connection Diagram .......................... 17
8. Specications ...................................... 18
9. Acronyms ............................................. 19
1
1. INTRODUCTION
The Auxiliary Control System for user utilizing it to cover the devices
which would like to be controlled. The benet for this auxiliary control
system makes daily life with more convenience. It comes with eight
trigger in which support 4 events to trigger. Moreover, four sets of relay
out and IR out to expand control coverage on desired devices. IR
In support IR learning function, device IR signal could be learned for
controlling device by remote control. The scheduling function with
daylight saving feature to provide the device be performed routinely
or at setting time. Comprehensive user control interfaces are available
which includes WebGUI, Telnet and console (RS-232 in). Installed with
adopt switching hub to offer PoE function which makes more exibility
on installation.
2. APPLICATIONS
• Smart Home Installation
• Even hall/Showroom control
3. PACKAGE CONTENTS
• 1 x Auxiliary Control System
• 1 x IR Receiver
• 1 x IR Blaster
• 1 x Remote Control (CR-157)
• 2 x 5pin Terminal Block
• 4 x 2pin Terminal Block
• 1 x 5V DC Power adaptor
• Operational Manual
4. SYSTEM REQUIREMENTS
Input source equipment such as light, TV, power switch and ….etc.
and PC/Laptop.
2
5. FEATURES
• 8 trigger in to active 8 events such as device on/ off and active
• 4 relay control out and IR out to control desired devices such as
screen down/up, lighting on/off
• IR In supported IR learner functions
• IR out supported for extend IR signal to further distance allowing
control the device installed in far end
• Multi user control interfaces includes WebGUI, Telnet and RS-232 (for
unit control)
• Easily setting on WebGUI includes scheduling, trigger and relay
setting
• PoE (power over Ethernet) supported
• Easily rmware update via USB le
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
1234
RELAY CONTROL OUT
1234
INFRARED OUT
IR IN
IR OUT
OUT
IN
GNDGND
321
GND
3.3V
12
3
21
1RELAY CONTROL OUT 1~4: Connect with control device’s power
± line cable such as A/C sensor, IR sensor, or curtain sensor for
control signal sending to activate the control devices.
2INFRARED OUT 1~4: Connect with IR Blaster, IR Receiver or 3.5mm
to D-Sub 9pin adaptor for IR signal transmitting or receiving.
4
6.2 Rear Panel
IR IN
TRIGGER IN
COMPORT
SERVICE
CONTROL
(POE)
POWER
DC 5V
1
5V
234
5
GND
678
54321
RXD
RS232
RS422
RS485
TXD GND
RX+RX- TD-TD+ GND
TD-TD+ GND
654321
1DC 5V: Plug the 5V DC power supply into the unit and connect the
adaptor to an AC outlet.
2CONTROL (POE): Connect with PC/Laptop or intra-net hub for
Telnet/WebGUI control over the devices. If the connected Hub
supports PoE function this device may not need to connect with
power supply.
3USB: This slot is reserved for factory rmware update only.
4COMPORT: These slots are to connect with comport control
devices such as RS-232/422/485 with RS baud rate up to 115200.
5TRIGGER IN: Connect with event device’s signal 5V lines such as
window security alarm, door switch, and etc… for trigger signal
sending back to Control System.
6IR IN: Connect with IR Receiver included in the package for IR
signal receiving and learning. Send the IR signal that is to be
learned by press on the remote control in direct line-of-sight
towards the Receiver and use the software to record the IR data
into digital format. For software details please refers to section 6.5.
5
6.3 IR Pin Denition
3
1
2
3
2
1
IR Signal
Power
Grounding
IR Learner
3
1
2
3
2
1
IR Blaster
Power
IR Blaster Signal
NC
IR Signal
Power
Grounding
IR Extender
Note: Due to both IR Extender and IR Learner cables are with similar
outlook, a part no. "CBL-IR10C3SA200A sticker has been placed to
differentiate the difference on IR Learner.
6
6.4 RS-232/Telnet Command List
Command Name Description Parameter
IPCONFIG Display The Current IP
Congure
NONE
SIPADDR
XXX.XXX.XXX.XXX
Set Ethernet IP
Address
XXX=0~255
SNETMASK
XXX.XXX.XXX.XXX
Set Ethernet Net Mask XXX=0~255
SGATEWAY
XXX.XXX.XXX.XXX
Set Ethernet
Gateway
XXX=0~255
SIPMODE N Set Ethernet IP Mode N= “STATIC” or “DHCP”
VER Show Unit Firmware
Version
NONE
FADEFAULT ALL Congure Set To
Factory Default
NONE
ETH_FADEFAULT ALL Ethernet
Congure Set To
Factory
NONE
REBOOT System Reboot NONE
HELP (?) Show Command List NONE
HELP N Show Descript Of
Command
N : Command Name
RELAY N N1 Relay Control N(PORT)= 1~4
N1=OPEN/CLOSE/
TOGGLE
IREMITE N N1 IR Control N(Port) = IR1~IR4
N1 = CYP Pronto Data
EX: IREMIT IR1
9333,0-157,AF,14,40,14,18
,14,43,14,1B,14,0-
Otros manuales para CDPS-CS6
1
Tabla de contenidos
Otros manuales de Sistema de control de CYP
