CYP CHDBX-1H1CE Manual de usuario
CHDBX-1H1CE
1 by 2 CAT5e/6/7 over HDMI & CAT5e/6/7 with LAN
and IR Splitter
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2013 by Cypress Technology.
All Rights Reserved.
Version 1.0 June 2013
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 14/04/14 Preliminary Release
CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel.........................................4
6.3 IR Cable Pin Assignment..................5
7. Connection Diagram ........................... 6
8. Specications ........................................ 7
8.1 CAT5e/6/7 Cable Specication .....8
9. Acronyms ............................................... 8
1
1. INTRODUCTION
The CAT5e/6/7 over HDMI and CAT5e/6/7 Splitter can convert a
single CAT5e/6/7 input, 2-way IR control and LAN serving to a single
CAT5e/6/7 output and includes a simultaneous HDMI bypass output.
It supports resolutions up to 1080p Full HD, 4K×2K timing, 3D and multi-
channel digital audio formats (such as LPCM 7.1CH, Dolby TrueHD,
Dolby Digital Plus and DTS-HD). The HDMI output can be connected
to an HDMI display or cascaded to another splitter. The CAT5e/6/7
output can be connected to a CAT5e/6/7 to HDMI Receiver to extend
the operating distance up to 100 meters.
Additionally, the LAN connectivity will allow a 100BaseT network to be
served to smart TVs or games consoles.
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• CAT5e/6/7 over HDMI & CAT5e/6/7 with LAN & IR Splitter
• IR Blaster x 1
• IR Extender x 1
• 24V DC Power Adaptor
• Operation Manual
4. SYSTEM REQUIREMENTS
• Source equipment with HDMI over CAT5e/6/7 Transmitter
• Display TV/Monitor with HDMI input connector
• HDMI over CAT5e/6/7 Receivers with industry CAT5e/6/7 cables
2
5. FEATURES
• HDMI with 3D & 4Kx2K supported, HDCP and DVI compliant
• Simultaneous HDMI and CAT5e/6/7 outputs
• Supports data rate from 250Mbps up to 3Gbps
• Supports wide range of PC resolutions from VGA to WUXGA
and HDTV resolutions up to 4Kx2K (3840x2160@24/25/30Hz,
4096x2160@24Hz and 4K2K@60 YUV_420)
• Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD
Master Audio transmission (32-192kHz sample rate)
• Supports distances up to 100 meters through CAT5e/6/7 cables
• Supports Ethernet network rate up to 100Mbps
• Can select EDID
• Supports USB service port
• Supports control of devices via 2-way IR
• The 3D signal display follow by display TV’s EDID
Note:
1. This system was tested with CAT6/23AWG cables, results may vary
withcablesofadifferentspecication.
2. Displaying HDMI 4Kx2K resolution require the standard 4Kx2K HDMI
cable and display in order for proper image displaying.
3. This device obtain the last memory function therefore, the device
will use last output port's EDID when the output is not connected to
a display after power cycling.
The unit will detect HDMI output's EDID when it obtain a 4Kx2K
EDID and send out the signal accordingly to other output ports. If
the HDMI output is without a 4Kx2K's EDID the unit will detect
all output's EDID and send out the signal that all outputs can
accept.
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
LAN CAT5e/6/7 IN
LINK POWER
SERVICE
DC 24V
1 2 3 4 5
1SERVICE: This slot is reserved for rmware update only.
2LAN: Connect to intranet or internet service system for a total
sharing rate of 100Mbps within the link of Transmitter.
Warning: DO NOT connect this slot with any of the CAT5e/6/7 port,
doing so may trigger a power shot down and ruin the device.
3CAT5e/6/7 IN & LINK LED: Connect from HDMI over CAT5e/6/7
Transmitter device along with source device for input signal
distribution up to 100m. Once the connection is made with active
signal the LINK LED will illuminate.
4POWER LED: Once the power supply is connected the LED will
illuminate.
5DC 24V: Plug the 24V DC power supply into the unit and connect
the adaptor to an AC outlet.
4
6.2 Rear Panel
HDMI OUTCAT5e/6/7 OUT
LINK LINK
IR IN IR OUT
EDID
A
AB
B
2 4 51 3
1HDMI OUT & LINK LED: Connect to HDMI display for instant image
display or cascade with another family type Transmitter. The LINK
LED will illuminate once and active display signal is detected.
This device obtain the last memory function therefore, the device
will use the last output port's EDID when The output port is not
connected to a display after power cycling.
2EDID: Switch to A/B to allows device to output image according to
output A/B (A: HDMI, B:CAT OUT) port's EDID. For example, switch
to A and both input and output A is connect to 4K2K's equivalence
signal, both output A and B will obtain a 4K2K's signal however
if output B is not connected with 4K2K's display there will be no
image.
3CAT5e/6/7 OUT & LINK LED: Connect this port to CAT5e/6/7 to HDMI
Receiver with CAT5e/6/7 cable along with display to extend the
signal up to 100m. Once the connection is made with active signal
the LINK LED will illuminate.
4IR IN: Connect with the supplied IR Extender to receive IR signal
from Transmitter side and blast out at Receiver side. Ensure that
remote controller being used is within the direct line-of-sight of the
IR Extender.
5IR OUT: Connect with the supplied IR Blaster to blast out the IR
signal received from the Receiver side. Place the IR Blaster in direct
line-of-sight of the equipment to be controlled.
5
6.3 IR Cable Pin Assignment
3
1
3
1
2
2
Power
IR Blaster Signal
NC
IR Signal
Power
Grounding
IR Extender
IR Blaster
Tabla de contenidos
Otros manuales de Cables y conectores de CYP
CYP
CYP CPRO-8ER Manual de usuario
CYP
CYP PUV-1820TX-AVLC Manual de usuario
CYP
CYP DT-12 Manual de usuario
CYP
CYP CPRO-8ER Manual de usuario
CYP
CYP PUV-1H4HPL-AVLC Manual de usuario
CYP
CYP CLUX-14EP Manual de usuario
CYP
CYP CDPS-UA1H10HS Manual de usuario
CYP
CYP CLUX-8M Manual de usuario
CYP
CYP CLUX-18S Manual de usuario
CYP
CYP CSDI-42 Manual de usuario
CYP
CYP CHDBT-1H2CE Manual de usuario
CYP
CYP CHDBT-1H3CL Manual de usuario
CYP
CYP CH-526RXPL Manual de usuario
CYP
CYP CPLUS-V2E Manual de usuario
CYP
CYP CPRO-U4T Manual de usuario
CYP
CYP CPLUS-V8PT Manual de usuario
CYP
CYP PU-1H7HBTPL Manual de instalación
CYP
CYP CDPS-4KQ Manual de usuario
CYP
CYP PU-1H3HBTL Manual de usuario
CYP
CYP CDVI-4S Manual de usuario
