CyberPowerPC Tracer Liquid Cooling Box Manual de usuario
Please read all instructions before using this liquid cooling box and
keep this manual always at hand.
The unit can be operated at an ambient temperature of
max. 35°C (95°F). Do not subject it to temperatures
below 5°C (41°F) or above 35°C (95°F).
CAUTION: Using unauthorized extension cables/tubes will
invalidate your warranty.
CAUTION: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate this device.
1
To guarantee your rights, please confirm the completeness
of the following information before you use it.
1.Liquid Cooling Box*1 (with rubber lid)
2.Black Dual Head Drain Plug*1
3.Water Tube*2
(with black and silver connectors attached to each end)
4.Hexagon Water Stopper*2
(it is connected to the Liquid Cooling Box)
5.User Manual*1
6.Other Accessories
CAUTION: : We conduct outgoing quality control (oqc)
with distilled water for each Liquid Cooling Box ensuring
a closed loop circuit where no leakage may occur.
MANRLCT011-P111
CAUTION: This product is intended to be supplied by Power
Adapter, output rated 19.5Vdc, 11.8A or 19.5Vdc, 16.9A or
20Vdc, 14A.
Tracer Liquid Cooling Box User Guide
2
Prepare your Liquid Cooling Box
1.Read the User Manual before operating Liquid Cooling Box.
2.Check if the (black and silver) connectors are attached to the
Water Tubes firmly.
3.Gently remove the Hexagon Water Stoppers on the Liquid Cooling
Box (do not throw it away, store it aside as it will be used later).
4.Gently attach (tighten the screws) the black connectors on the
Water Tubes to the Liquid Cooling Box, make sure it is attached
firmly and avoid twisting tubes.
5.Place the Liquid Cooling Box horizontally on the desk.
Attach the black connectors to the Liquid Cooling Box firmly by
tightening the screw. Avoid from twisting tubes while and after
attaching to the Liquid Cooling Box.
Gently remove the Hexagon
Water Stoppers by loosening the
screw and store aside.
CAUTION: Do not use wrench to lock the water pipe.
Tighten with fingers can prevent water leakage.
Improper force may damage the joint.
3
Connect Liquid Cooling Box to the Laptop
1.Place the laptop on the desk, open the rubber flap on the rear
side of the laptop.
2.Insert the silver connector in parallel to the laptop, you will hear a
small click sound when attached correctly (note. refrain from
twisting the Water Tubes and keep it at bent state instead of
straightening the tubes).
3.Connect the power adaptor to the Liquid Cooling Box’s DC port
(note. don’t plug in the power yet).
4.Connect Liquid Cooling Box’s DC Cable to the laptop’s DC port
(note. don’t plug in the power yet).
Parallelly insert connectors
into the laptop.
DC INPUT: 230 Watts (19.5V/11.8A)
280 Watts (20V/14A) Option
330 Watts (19.5V/16.9A) Option
4
Inject water into the Liquid Cooling Box
1.Open the rubber lid on the Liquid Cooling Box, note that the water
injection hole is quite small (ventilation hole is on the right hand
side), recommend using a syringe or funnel for assistance when
injecting water. Also, distilled water is recommended.
2.After filling in distilled water, long press the power button located
on the Liquid Cooling Box for 4-5 seconds. The power button will
glow in purple indicating entering “Water Injection Mode”.
3.Alternatively, open the application “Control Center” in your laptop,
click “Performance” then “Liquid Cooling System Control” module.
Press the “helper” button and click on “Water Injection Mode” to
enter water injection mode.
4.Monitor the water level when injecting the water, add the water
above the MAX indicator for the first time (note. under normal
circumstances, the silver connector will not leak water).
5.Avoid tilting the Liquid Cooling Box, after filling in the water, recap
the rubber lid and make sure that no leakage is observed.
water injection hole
5
Operate your Liquid Cooling Box
1.Plug in the power cord to the power socket.
2.Turn on the laptop and make sure the Bluetooth is turned on as well.
3.Press the power button on the Liquid Cooling Box and the LED
indicator will start glowing.
4.Open the application “Control Center”, click “Performance” then
“Liquid Cooling System Control” module, the application will pop up
“Helper Manual”.
5.After selecting “Device” and Click “connect” button then Liquid Cooling
Box and the laptop will pair via Bluetooth (the fan and water pump
are then activated).
6.Check all ports for leakage after five minutes, if there is, turn off the
power and reconnect the port.
7.The water level drops in standard operation, please add distilled
water and make sure the water level is above the marker indicator
(note. please reference 4-3).
Liquid Cooling Box and laptop will pair automatically via Bluetooth after first pairing:
a, if both are in Bluetooth distance
b, laptop has Control Center installed
6
Disconnect your Liquid Cooling Box
1.Disconnect the Bluetooth via application “Control Center”-
“Performance” - “Liquid Cooling System Control”.
2.Turn off the power (of the Liquid Cooling Box) only when the fan
stopped turning.
Note. The mentioned steps apply to normal installation and usage of
Liquid Cooling Box (e.g. fixed environment).
7
Disconnect the Water Tubes
When you finished using the Liquid Cooling Box, and intend to
disconnect the Water Tubes, please follow the instructions listed below:
1.Turn off the power by pressing the power button on the Liquid
Cooling Box.
2.Gently squeeze the silver connector which is connected to the laptop
and remove it from the laptop horizontally.
Squeeze the silver connector and remove
it from the laptop horizontally.
To reduce the possibility of heat-induced injury or equipment overheating:
1. In the case that the connector is connected and the water is not flowing, the
connector may accumulate heat in the metal part because of the temperature generated
by the operation of the system, so please be aware of the high temperature.
2. If you want to remove the quick release connector, make sure the Liquid Cooling Box
is turned off (to avoid water leakage) and test the connector by hand to make sure the
temperature is not too high before removing it.
8
Change water or Travel
If you are to change the water or need to travel, please follow the
instructions listed below:
1.Since system operation may lead to accumulated heat in the silver
connector, recommend removing the connector horizontally only after
turning off the device.
2.Insert into laptop’s drain tubes (4mm deep) to assist draining
additional liquid in the laptop.
3.Put laptop’s rubber flap back on (squeeze it tight) to avoid minor water
leakage.
4.Insert on to the silver connector to drain the liquid in the Liquid
Cooling Box.
5.Remove the Black Dual Head Drain Plug when the liquid is emptied, and
gently tighten the Hexagon Water Stoppers on to the drain port.
If you intend to remove the Black Dual Head Drain Plug, squeeze the silver
connector to unlock and remove it after.
1.If you need to travel, please empty the liquid in the Liquid Cooling Box, Water Tubes,
and laptop’s liquid cooling copper pipes to avoid water leakage during transportation,
which may lead to device malfunction.
2.To prevent from water scale, please change the water regularly.
3.Check if there are water leakage when connecting or disconnecting the device, and
clean up in time.
1
2
1
2
Front side view/ Back side view
Left side view/ Right side view
The power cord can be stored around the base
9
Product Overview
1
3
4
5
2
Top side view/ Bottom side view
1
2
3
4
5
6
Drain Pipes
RGB LED
DC Port
Vents
Power Connector
Rubber Lid
LED Indicator*
Power Button
7
8
6
7
8
*(Colors for BT/Pump injection water/ lightbar)
1. Water injection : Blinking(Purple color)
2. BT searching :Blinking (Blue color)
3. BT ready : on (Blue color)
4. Liquid cooling system error : Blinking
(Pump idling _Orange color)
Tabla de contenidos
Manuales populares de Hardware de computadora de otras marcas
EMC2
EMC2 VNX Series Manual del propietario
Panasonic
Panasonic DV0PM20105 Manual de usuario
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manual de usuario
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manual de usuario
Raidon
Raidon iT2300 Manual de usuario
National Instruments
National Instruments PXI-8186 Manual de usuario
