CyberPower RMCARD400 Manual de usuario
Copyright © 2022 Cyber Power Systems, Inc. All rights reserved.
QUICK START GUIDE
Remote Management CardRemote Management Card
RMCARD400
RMCARD401
SAVE THESE INSTRUCTIONS
Please read this guide and follow the instructions for installation and use.
K01-0000975-00
Tx/Rx
Link
Universal
RMCARD400
CyberPower
Tx/Rx
Link
Universal
RMCARD401
CyberPower
USB
Table of Contents
INTRODUCTION.......................................................... 1
Overview ............................................................................. 1
System Requirements.................................................... 1
Unpacking........................................................................... 1
Front Panel ......................................................................... 2
LED Status Indicator.......................................................2
INSTALLATION ...........................................................3
Step 1. Hardware Installation ....................................3
Step 2. Configure the IP Address .............................4
WEB INTERFACE ........................................................6
Login User Account .......................................................6
FIRMWARE UPGRADE................................................6
RESET TO FACTORY DEFAULT SETTING/
RECOVER FROM A LOST PASSWORD ...................9
SOFTWARE SUPPORT..............................................10
TROUBLESHOOTING ...............................................1 1
CONFORMANCE APPROVALS ...............................12
i
1
INTRODUCTION
Overview
The CyberPower Remote Management Card allows a UPS system
and environmental sensor to be managed, monitored, and
configured. After installing the hardware and configuring an IP
address, the user can access, monitor, and control the UPS from
anywhere in the world! Simply use a web browser or SSH client to
access your UPS. Servers and workstations can be protected by
the UPS utilizing PowerPanel® Business Remote to gracefully
shutdown when signaled by the Remote Management Card.
System Requirements
● A 10/100/1000Mbps Ethernet connection to an existing network
● Web Browser or SSH client
● (Optional) NMS (Network Management System) compliant with
SNMP
● RMCARD400 supports the CyberPower's UPS models which
have smart slot.
(RMCARD401 supports the new specific UPS models)
Unpacking
Inspect the Remote Management Card upon receipt. The package
should contain the following:
● CyberPower Remote Management Card
● RJ45/DB9 Serial Port Connection Cable
● Quick Start Guide
● Spare Jumper
LED Status Indicators
1
3
1. Universal Port
2. Ethernet Port
3. Tx/Rx Indicator
4. Link Indicator
5. USB Port
RMCARD400
RMCARD401
2
Universal Link Tx/Rx
Universal Link Tx/Rx USB
RMCARD400
RMCARD401
Front Panel
2
4
1 2
4
3
5
Link LED
O
On (Yellow)
On (Green)
Tx/Rx LED
O
On (Green)
Flashing (Green)
Condition
The Remote Management Card is not
connected to the Network / or the Remote
Management Card power is o
The Remote Management Card is connected
to the Network (10/100Mbps Speed)
The Remote Management Card is connected
to the Network (Up to 1000Mbps Speed)
The Remote Management Card power is o
The Remote Management Card power is on
- Receiving/transmitting data packet
- Reset finished
INSTALLATION
5. (Optional) To connect an
environmental sensor, use a
RJ45 Ethernet cable. Connect
one end to the Universal port
on the RMCARD and the other
end into the sensor. For more
information, please see the
ENVIROSENOR user’s manual.
NOTE: The CyberPower Remote Management Card is hot-swappable, so you
do not need to turn o the device to install it.
NOTE: Please do not remove or modify SDCARD on the back. CyberPower is
not responsible for any unauthorized modification to RMCARD400/401.
4. Connect an Ethernet cable to
the Ethernet port of the
CyberPower Remote
Management Card.
3. Insert and tighten the
retaining screws.
2. Install the CyberPower
Remote Management Card
into the expansion slot.
1. Remove the two retaining
screws of the expansion
slot, and then remove the
cover.
Step 1. Hardware Installation
3
RMCARD400/401
CyberPower
Universal
Tx/Rx
RMCARD400
sal Tx/Rx
CyberPower
CARD400
Tx/Rx
Link
Universal
RMCARD400
CyberPower
4. Select the Remote Management Card you are setting up. Click
on the Tools menu and select the Remote Management Card
you want to configure. Then, click the "Connection" button on
the top tools list to set up.
5. You will need to enter a User
Name and Password for the
Remote Management Card in
the authentication window, as
shown in Figure 2.
- Default user name: cyber
- Default password: cyber
4
Step 2. Configure the IP Address for the CyberPower
Remote Management Card
Method 1: Using the Power Device Network Utility 2
1. Install the Power Device Network Utility 2 available for
download at www.CyberPower.com.
2. After installation completes, run the “Power Device Network
Utility 2”.
3. The main window of the Power Device Network Utility 2
program is shown in Figure 1. The configuration tool will
display all CyberPower Remote Management devices present
on the local network subnet. The "Refresh" button is used to
search the local network subnet again.
Figure 2. Authentication window
Figure 1. The main window of the “Power Device Network Utility 2” program
5
7. Modify the IP, subnet mask or gateway address. Enter the new
addresses into the corresponding fields and then click “Save”.
6. You can modify the IP Address,
Subnet Mask, and Gateway
address for the Device MAC
Address listed in the Device
Network Settings window, as
shown in Figure 3.
The factory default IP Address
is 192.168.20.177 and the
default Subnet Mask is
255.255.255.0.
Figure 3. The Device Network setting window
WEB INTERFACE
Login User Account
You will need to enter a User Name and Password to login to the
interface, and can select a preferred language after login. There are
two user account types.
1. Administrator
- Default username: cyber
- Default password: cyber
2. View only
- Default username: device
- Default password: cyber
You will be asked to reset a username and password upon the first
login. The administrator can access all functions, including
enable/disable the view only account. The viewer can access read
only features but cannot change any settings. For detailed
descriptions and explanations of the Web UI, please refer to
RMCARD User’s Manual.
FIRMWARE UPGRADE
By upgrading the firmware, you can obtain both the new features
and updates/improvements to existing functionality. To ensure the
RMCARD firmware is kept up to date, please visit our website
every 3 months to see if there is any updated firmware version
available. You can check the “Firmware version” on the
[System->About] page on the web user interface of the RMCARD.
There is one file to update in order to upgrade the firmware version.
- cpsrm4safw_XXX
NOTE: Please do not turn the UPS o when processing the Firmware upgrade.
6
7
Using Power Device Network Utility
Install the CyberPower Power Device Network Utility 2 available for
download at www.CyberPower.com.
1 . After installation completes, run the “Power Device Network Utility 2”.
2 . The main window of the Power Device Network Utility 2 program
is shown in Figure 4. The configuration tool will display all
CyberPower Remote Management devices present on the local
network subnet. The "Scan" button is used to search the local
network subnet again.
NOTE: You can click “Scan” and select the items you want to view.
3 . Check the boxes to select the devices you wish to upgrade, and
select “Connection” on to connect the device user account and
password. Once the connection is confirmed the status icon next
to the IP Address will change from grey to green.
Note: You must connect to the device by entering user account
and password credentials before firmware upgrade.
4 . Select the devices you wish to upgrade by checking their
respective checkbox and select “Upload Firmware”.
NOTE: You can upload the firmware of multiple devices that use the same
firmware files
Figure 4. The main window of the “Power Device Network Utility 2” program.
6 . Select the Firmware and click “OK” to implement firmware
upgrade, as shown in Figure 5.
7 . If the firmware upgrade is implemented, you will see the Result in
the main window, as shown in Figure 6.
Figure 6. Firmware upgrade success in the main window.
Figure 5. The File Locations of Firmware & Data window.
8
Otros manuales para RMCARD400
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Unión Postal Universal de CyberPower
CyberPower
CyberPower Value600EI-AU Manual de usuario
CyberPower
CyberPower CSN30C12V-E Manual de usuario
CyberPower
CyberPower Professional Rack Mount UPS 2200VA Manual de usuario
CyberPower
CyberPower CST135UC2 Manual de usuario
CyberPower
CyberPower BPSE36V45A Manual de usuario
CyberPower
CyberPower Paragon OL3000RMXL2U Manual de usuario
CyberPower
CyberPower OR1500LCDRM1U Manual de usuario
CyberPower
CyberPower AVR CP850PFCLCD Manual de usuario
CyberPower
CyberPower Paragon OL1000RMXL2U Manual de usuario
CyberPower
CyberPower SE450G1 Manual de usuario
CyberPower
CyberPower 649532830022 Manual de usuario
CyberPower
CyberPower BU600E Manual
CyberPower
CyberPower PR1000LCD Manual de usuario
CyberPower
CyberPower PR750ELCD Manual de usuario
CyberPower
CyberPower CP900AVR Manual de usuario
CyberPower
CyberPower BR700ELCD Manual de usuario
CyberPower
CyberPower Professional Tower UPS PP1500E Manual de usuario
CyberPower
CyberPower UT400EG Manual de usuario
CyberPower
CyberPower STANDBY UPS Series Manual de usuario
CyberPower
CyberPower 649532215003 Manual de usuario
Manuales populares de Unión Postal Universal de otras marcas
Pylontech
Pylontech Victron & Pylontech US5000 Manual de usuario
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario
Mecer
Mecer ME-1000-WTU Manual de usuario
Mustek
Mustek PowerMust 530(B) Plus Manual de instalación y operación
Emerson
Emerson Liebert NXL series Manual de usuario
MAKELSAN
MAKELSAN BOXER SERIES Manual de usuario
