CyberPower CST1500SUC Manual de usuario

PFC SINEWAVE UPS SERIES

CST1500SUC

USER MANUAL

YOUR ULTIMATE ALLY IN POWER

Cyber Power Systems (USA), Inc.

4241 12th Avenue East, Suite 400 | Shakopee, MN 55379 | CyberPowerSystems.com

FEATURES

1. Power Switch

2. Power On Indicator

3. LCD module display

4. Down/Display button

5. Up/Mute button

6. Enter/Setup Button

7. USB Charging Ports

8. Battery and Surge Protected Outlets

9. Full-Time Surge Protected Outlets

10. Circuit Breaker

11. Serial/USB Ports to PC

12. Communication Protection Ports (RJ45)

13. Wiring Fault Indicator (red)

14. Coax/Cable/DSS Surge Protection

Thank you for purchasing a CyberPower product. Please take a few minutes to register your

product at www.cyberpowersystems.com/registration/.

Registration certiﬁes your product’s warranty, conﬁrms your ownership in the event of a product

loss or theft and entitles you to free technical support. Register your product now to receive the

beneﬁts of CyberPower ownership.

CAUTION! To prevent the risk of ﬁre or

electric shock, install in a temperature

and humidity controlled indoor area free

of conductive contaminants. (Please see

speciﬁcations for acceptable temperature and

humidity range).

CAUTION! To reduce the risk of electric

shock, do not remove the cover except to

service the battery. Turn o and unplug the

unit before servicing the batteries. There are

no user serviceable parts inside except for the

battery.

CAUTION! Hazardous live parts inside can be

energized by the battery even when the AC

input power is disconnected.

CAUTION! The UPS must be connected to an

AC power outlet with fuse or circuit breaker

protection. Do not plug into an outlet that is

not grounded. If you need to de-energize this

equipment, turn o and unplug the unit.

CAUTION! To avoid electric shock, turn o

the unit and unplug it from the AC power

source before servicing the battery or

installing a computer component.

CAUTION! Not for use in a computer room

as deﬁned in the Standard for the Protection

of Electronic Computer/Data Processing

Equipment, ANSI/NFPA 75.

CAUTION! To reduce the risk of ﬁre, connect

only to a circuit provided with 20 amperes

maximum branch circuit over current

protection in accordance with the National

Electric Code, ANSI/NFPA 70.

CAUTION! DO NOT USE FOR MEDICAL

OR LIFE SUPPORT EQUIPMENT! DO NOT

use in any circumstance that would aect

the operation and safety of life support

equipment, medical applications, or patient

care.

CAUTION! DO NOT USE WITH OR NEAR

AQUARIUMS! To reduce the risk of ﬁre or

electric shock, do not use with or near an

aquarium. Condensation from the aquarium

can cause the unit to short out.

CAUTION! DO NOT USE THE UPS ON ANY

TRANSPORTATION! To reduce the risk of ﬁre

or electric shock, do not use the unit on any

transportation such as airplanes or ships. The

eect of shock or vibration caused during

transit and the damp environment can cause

the unit to short out.

PRODUCT REGISTRATION

IMPORTANT SAFETY WARNINGS (SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions

carefully during installation and operation of the unit. Read this manual thoroughly before

attempting to unpack, install, or operate your UPS.

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt.

The box should contain the following:

(a) UPS unit

(b) User’s manual

(d) Function Setup Guide

SUPPORTS ACTIVE PFC POWER SUPPLIES

This CyberPower UPS system delivers sine wave

output, which is ideal for seamless operation

of computers using high eciency switching

power supplies with Active Power Factor

Correction (Active PFC), home entertainment

systems, and other sensitive electronics.

OVERVIEW

The CST1500SUC provides complete power

protection from utility power that is not always

consistent. The CST1500SUC features 1445

Joules of surge protection. The unit provides

long lasting battery backup during power

outages with maintenance free batteries. The

CST1500SUC ensures consistent power to

your computer system and includes software

that will automatically save your open ﬁles

and shutdown your computer system during a

utility power loss.

AUTOMATIC VOLTAGE REGULATOR

The CST1500SUC uses

Automatic Voltage

Regulation (AVR) to

stabilize inconsistent utility

power voltage to levels

that are safe for connected

equipment. AVR safeguards

hardware and important

data ﬁles by automatically increasing low utility

power to a consistent and safe output voltage

while preserving battery power for outages.

DETERMINE THE POWER REQUIREMENTS

OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into

the outlet does not exceed the UPS unit’s

rated capacity. If the rated capacities of the

unit are exceeded, an overload condition

may occur and cause the UPS unit to shut

down or the circuit breaker to trip.

2. There are many factors that can aect

the amount of power that your computer

system will require. It is suggested that

the load placed on the battery outlets not

exceed 80% of the unit’s capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately

upon receipt. However, after receiving a

new UPS, to ensure the battery’s maximum

charge capacity, it is recommended that

you charge the battery for at least 8 hours.

Your UPS is equipped with an auto-charge

feature. When the UPS is plugged into an

AC outlet, the battery will automatically

charge whether the UPS is turned on or o.

Note: This UPS is designed with a safety

feature to keep the system from being

turned on during shipment. The ﬁrst time

you turn the UPS on, you will need to have

it connected to AC power or it will not

power up.

2. With the UPS unit turned o and

unplugged, connect your computer,

monitor, and any other peripherals

requiring battery backup into the battery

power supplied outlets. DO NOT plug a

laser printer, paper shredder, copier, space

heater, vacuum, sump pump or other

large electrical devices into the “Battery

and Surge Protected Outlets”. The power

demands of these devices may overload

and damage the unit.

- continued

PLUG IN

INSTALLING YOUR UPS SYSTEM - continued

3. Plug the UPS

into a 2 pole, 3

wire grounded

receptacle (wall

outlet). Make sure

the wall branch

outlet is protected

by a fuse or circuit breaker and does not

service equipment with large electrical

demands (e.g. air conditioner, copier, etc…).

The warranty prohibits the use of extension

cords, outlet strips, and surge strips.

4. Press the power switch to turn the unit on.

The Power On indicator light will illuminate

and the unit will “beep”. If an overload is

detected, an audible alarm will sound and

the unit will emit one long beep. To correct

this, turn the UPS o and unplug at least one

piece of equipment from the battery power

supplied outlets. Make sure the circuit breaker

is depressed and then turn the UPS on.

5. To maintain optimal battery charge, leave

the UPS plugged into an AC outlet at all

times.

6. To store the UPS for an extended period,

cover it and store with the battery fully

charged. While in storage, recharge the

battery every three months to ensure

battery life.

7. Ensure the wall outlet and UPS are located

near the equipment being attached for

proper accessibility.

SYSTEM FUNCTION BLOCK DIAGRAM

Advanced Energy-Saving Patented Bypass Technology

The GreenPower UPS™ has a high-eciency charger, which makes it the most energy-

ecient UPS in its class. The advanced high-frequency charging system signiﬁcantly

improves charging eciency and conserves energy. As a result of this advanced design,

the GreenPower UPS™ uses less energy compared to competitive models. The GreenPower

UPS™ is manufactured in accordance with the Restriction on Hazardous Substances (RoHS)

directive making it one of the most environmentally-friendly UPS on the market today.

CYBERPOWER GREENPOWER UPS™ TECHNOLOGY

REEN

POWER UPS™

Energy-Saving Technology

Input Output

EMI Fllter Surge

Suppressor AVR

Charger

AC / DC Battery Inverter

Normal Mode

Battery Mode

BASIC OPERATION

1. Power Switch

Used as the master on/o switch for

equipment connected to the battery power

supplied outlets.

2. Power On Indicator

This LED is illuminated when the utility

power is normal and the UPS outlets are

providing power, free of surges and spikes.

3. LCD Module Display

High resolution and intelligent LCD display

shows all the UPS information using icons

and messages. For more information

please review the “Deﬁnitions for

Illuminated LCD Indicators” section below.

4. Down/Display Button

The button can be used to select the LCD

display contents including Input Voltage,

Output Voltage, and Estimated Run Time.

Short press the button to scroll down the

function menu. Pressing the button for 2

seconds will keep the LCD display always

on or turn the LCD display o while in AC/

Utility power mode. For more information

about the Down/Display Button, please

refer to the Function Setup Guide.

5. Up/Mute Button

Short press the button to scroll up the

function menu. Holding the button for

more than 2 seconds will silence the alarm.

For more information about the Up/Mute

Button, please refer to the Function Setup

Guide.

6. Enter/Setup Button

Press the button for 2 seconds to enter the

setup menu and then select the functions

for conﬁguration. For more information

about the Enter/Setup Button, please refer

to the Function Setup Guide.

7. USB Charging Ports

The USB charging ports (Type A and Type

C) provide 30W PD power output with

battery backup.

8. Battery and Surge Protected Outlets

The unit has 6 battery powered/surge

suppression outlets for connected

equipment to ensure temporary

uninterrupted operation of your equipment

during a power failure. (DO NOT plug a

laser printer, paper shredder, copier, space

heater, vacuum, sump pump or other

large electrical devices into the “Battery

and Surge Protected Outlets”. The power

demands of these devices may overload

and damage the unit.)

9. Full-Time Surge Protected Outlets

The unit has 6 surge suppression outlets.

10.Circuit Breaker

Located on the back of the UPS, the circuit

breaker serves to provide overload and

fault protection.

11. Serial/USB Ports to PC

The USB port allows connection and

communication between the USB port on

the computer and the UPS unit.

12. Communication Protection Ports (RJ45)

Bi-directional communication ports provide

surge protection to a 10/100/1000 Ethernet

connection.

13. Wiring Fault Indicator (red)

This LED indicator will illuminate to warn

the user that a wiring problem exists, such

as bad ground, missing ground or reversed

wiring. If this is illuminated, disconnect

all electrical equipment from the outlet

and have an electrician verify the outlet is

properly wired. The unit will not provide

surge protection without being plugged

into a grounded and properly wired wall

outlet.

14.Coax/Cable/DSS Surge Protection

The Coax/Cable/DSS protection ports will

protect any cable modem, CATV converter,

or DSS receiver.

Replacement of batteries located in an

OPERATOR ACCESS AREA.

1. When replacing batteries, replace with

the same number of the following battery:

CyberPower / RB1290X2.

2. CAUTION! RISK OF EXPLOSION

IF BATTERY IS REPLACED BY AN

INCORRECT TYPE. DISPOSE OF USED

BATTERIES ACCORDING TO LOCAL

REGULATIONS.

3. CAUTION! Risk of Energy Hazard, 24 V,

maximum 9 Ampere-hour battery. Before

replacing batteries, remove conductive

jewelry such as chains, wrist watches, and

rings. High energy conducted through

these materials could cause severe burns.

4. CAUTION! Do not dispose of batteries in a

ﬁre. The batteries may explode.

5. CAUTION! Do not open or mutilate

batteries. Released material is harmful to

the skin and eyes. It may be toxic.

6. CAUTION! A battery can present a risk

of electrical shock and high short circuit

current. The following precautions should

be observed when working on batteries:

(1) Remove watches rings, or other metal

objects.

(2) Use tools with insulated handles.

REPLACING THE BATTERY

BATTERY REPLACEMENT PROCEDURE: CST1500SUC

1. Turn the UPS on its side.

2. Remove the front panel retaining screws located on the bottom of the UPS.

3. Slide the front panel completely o of the unit.

4. Remove the ﬁxed stand from the upper battery.

5. Remove the batteries from the compartment.

6. Disconnect the battery wires from the batteries.

7. Install the replacement batteries by connecting the red wire (+) and black wire (-) to the

same color connectors from both the upper and lower battery pack. Note: Only use new

batteries for replacement and both batteries should be replaced at the same time to ensure

maximum life span.

8. Put the batteries back into the compartment and reattached the ﬁxed stand.

9. Slide back the battery compartment cover and tighten the retaining screws.

10. Recharge the UPS for 8-16 hours to fully charge the battery.

REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly. Most retailers that sell lead-acid

batteries collect used batteries for recycling, as required by local regulations.

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

1. ONLINE:

The UPS is supplying utility power to

connected equipment.

2. BATTERY:

During a severe brownout or blackout,

this icon appears and an alarm sounds

(two short beeps followed by a pause)

to indicate the UPS is operating from its

internal batteries. During a prolonged

brownout or blackout, the alarm will beep

rapidly every 1/2 second to indicate the

UPS’s batteries are nearly out of power.

You should save ﬁles and turn o your

equipment immediately or allow the

software to shut the system down.

3. ENERGY-SAVING:

The UPS in energy-saving bypass mode.

See “CyberPower GreenPower UPSTM

Technology” section for more information.

4. LOAD CAPACITY/SENSITIVITY SETUP:

LOAD capacity: This meter displays the

approximate output load level (in 20%

increments) of the UPS battery outlets.

Sensitivity setup: This meter is also used to

setup the UPS sensitivity when you are in

the programming mode. If the connected

equipment can tolerate more power

events (example: unstable power often

associated with stormy weather), select

Low Sensitivity and the UPS will go to

Battery Mode less often. If the connected

equipment is more sensitive to power

events, select High Sensitivity and the UPS

will go to Battery Mode more often.

5. BATTERY CAPACITY:

This meter displays the approximate

charge level (in 20% increments) of the

UPS’s internal battery. During a blackout

or severe brownout, the UPS switches to

battery power, the BATTERY icon appears,

and the charge level decreases.

6. FAULT:

This icon appears if there is a problem with

the UPS. Press the POWER button to turn

the UPS o.

F01: Battery Mode or AC/Utility Power

Mode Overload fault (Unplug at least one

piece of equipment from battery outlets

and turn the UPS on again.)

F02: Battery Output Short fault (Unplug at

least one piece of equipment from battery

outlets and turn the UPS on again.)

F03: Charger Fault (Contact CyberPower

Systems for support.)

F04: Internal Fault (Contact CyberPower

Systems for support.)

7. OVERLOAD:

This icon appears and an alarm sounds to

indicate the battery-supplied outlets are

overloaded. To clear the overload, unplug

one piece of equipment from the battery-

supplied outlets at a time until the icon

turns o and the alarm stops.

8. SCHEDULE:

Users can setup the schedule to turn on

and shut down the computer and UPS

through PowerPanel® Personal software.

The LCD display will show how much time

is left before the UPS will turn back on or

shut down.

9. ESTIMATED RUNTIME:

This displays the run time estimate of the

UPS with current battery capacity and load.

10.OUTPUT METER:

This meter measure, in real time, the AC

voltage that the UPS system is providing

to the computer, such as normal AC line

mode, AVR mode, and battery backup

mode. (Note: The OUTPUT meter shows

the status of the battery backup outlets in

terms of load, frequency, and voltage.)

1 3

1314

52 15

For more information about functions setup, please refer to the Function Setup Guide.

DEFINITIONS FOR ILLUMINATED LCD INDICATORS - continued

TROUBLESHOOTING

Problem Possible Cause Solution

Circuit breaker button is

projecting from the back of the

unit.

Circuit breaker has tripped due to

an overload.

Turn the UPS o and unplug at

least one piece of equipment.

Wait 10 seconds, reset the circuit

breaker by depressing the button,

and then turn the UPS on.

The UPS does not perform

expected runtime.

Battery not fully charged. Recharge the battery by leaving

the UPS plugged in.

Battery is worn out. Contact CyberPower about

replacement batteries.

The UPS will not turn on.

The on/o switch is designed

to prevent damage from rapidly

turning it o and on.

Turn the UPS o. Wait 10 seconds

and then turn the UPS on.

The unit is not connected to an AC

outlet.

The unit must be connected to a

110/120V 60Hz outlet.

The battery is worn out. Contact CyberPower about

replacement batteries.

Mechanical problem. Contact CyberPower.

PowerPanel® Personal/Business

software is inactive

(all icons are gray)

The USB / serial cable is not

connected.

Connect the USB / serial cable

to the UPS unit and an open USB

/ serial port on the back of the

computer.

The USB / serial cable is

connected to the wrong port.

Check the back of the computer

for an additional USB / serial port.

Move the cable to this port.

11. INPUT Meter:

This meter measures the AC voltage that

the UPS system is receiving from the utility

wall outlet. The UPS is designed, through

the use of automatic voltage regulation,

to continuously correct output voltage to

connected equipment to a safe 110/120

voltage output range. In the event of a

complete power loss, severe brownout, or

over-voltage, the UPS relies on its internal

battery to supply consistent 110/120 output

voltage. The INPUT voltage meter can

be used as a diagnostic tool to identify

poor-quality input power.

12. EVENT: This meter records the number of

power outages.

13. MUTE:

This icon appears whenever the UPS is

in silent mode. However, when there is a

problem with the UPS, the alarm will still

beep even in silent mode.

14.AVR (Automatic Voltage Regulation):

This icon appears whenever your UPS is

automatically correcting low or high AC

line voltage without using battery power.

This is a normal, automatic operation of

your UPS, and no action is required on your

part.

15. REPLACE BATTERY:

This icon illuminates when the batteries are

not connected well or the batteries were

worn out.

TROUBLESHOOTING - continued

TECHNICAL SPECIFICATIONS

Problem Possible Cause Solution

PowerPanel® Personal/Business

software is inactive

(all icons are gray).

The unit is not providing battery

power.

Shutdown your computer and turn

the UPS o. Wait 10 seconds and

turn the UPS back on. This should

reset the unit.

The USB charging ports are

not providing power to the

connected devices.

The USB power port has Over

Current Protection design.

When the total current of

connected devices is over

speciﬁcation, the USB power ports

will stop providing power to the

connected devices.

Turn the UPS o and unplug

at least one piece of device

connected to the USB charging

port and then turn the UPS on.

Additional troubleshooting information can be found under “Support” at www.CyberPowerSystems.com.

Model CST1500SUC

Capacity 1500VA / 900W

Nominal Input Voltage 120V

Input Frequency 60 Hz +/- 3 Hz

On-Battery Output Voltage 120Vac +/- 5%

On-Battery Output Wave Form Sinewave

Operating Temperature + 32°F to 104°F / 0°C to 40°C

Operating Relative Humidity 0 to 95% non-condensing

Size (L x W x H) 3.9" x 11" x 14" (100 x 280 x 355 mm)

Net Weight 24.91lbs / 10.6kg

Battery Type Sealed Maintenance Free Lead Acid Battery

Typical Battery Recharge Time 8 hours to 90% (from full load discharge)

Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles

Safety Approvals UL1778, CSA C22.2 No 107.3, FCC Class B

Recommended Battery CyberPower / RB1290X2

Please visit www.CyberPowerSystems.com for a copy of the Limited Warranty and Connected

Equipment Guarantee.

Where Can I Get More Information?

The application of the United Nations Convention of Contracts for the International Sale of

Goods is expressly excluded. CyberPower is the warrantor under this Limited Warranty.

For further information please feel free to contact CyberPower at:

Cyber Power Systems (USA), Inc. 4241 12th Ave E., STE 400, Shakopee, MN 55379;

call us at (877) 297-6937; or submit a web ticket online at cyberpowersystems.com/support.

Cyber Power Systems (USA), Inc. encourages environmentally sound methods for disposal

and recycling of its UPS products. Please dispose and/or recycle your UPS and batteries in

accordance to the local regulations of your state.

WARNING: This product can expose you to chemicals including bisphenol A (BPA) and styrene, which is known to the

State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.

LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE

FCC COMPLIANCE STATEMENT

FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment to an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Important: Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Canadian Compliance Statement

CAN ICES-3 (B)/NMB-3(B)

K01-00001009-00

Tabla de contenidos

Otros manuales de Unión Postal Universal de CyberPower

CyberPower

CyberPower UT850E-FR/UPS Manual de usuario

CyberPower

CyberPower PR1000LCD Manual de usuario

CyberPower

CyberPower UP425 Manual de usuario

CyberPower

CyberPower DL450ELCD Manual de usuario

CyberPower

CyberPower Value800EI Manual de usuario

CyberPower

CyberPower PR750LCDRM1U Manual de usuario

CyberPower

CyberPower PR750ELCD Manual de usuario

CyberPower

CyberPower UPS BR850ELCD Manual de usuario

CyberPower

CyberPower Value1200ELCD Manual de usuario

CyberPower

CyberPower SM20KPM Manual de usuario

CyberPower

CyberPower UT650E-FR/UPS Manual de usuario

CyberPower

CyberPower OL6000RT3UPDU Manual de usuario

CyberPower

CyberPower 649532005024 Manual de usuario

CyberPower

CyberPower DX650E Manual de usuario

CyberPower

CyberPower PR1000ELCDRT2U Manual de usuario

CyberPower

CyberPower PR1500LCDRTXL2U Manual de usuario

CyberPower

CyberPower OL8KRT Manual de usuario

CyberPower

CyberPower AVRG750LCD Manual de usuario

CyberPower

CyberPower OL6KRT Manual de usuario

CyberPower

CyberPower 649532715039 Manual de usuario

CyberPower

CyberPower CP1000AVRL Manual de usuario

CyberPower

CyberPower PR5000ELCDRTXL5U Manual de usuario

CyberPower

CyberPower BU600E Manual de usuario

CyberPower

CyberPower OL6000ERT3UD Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario

ZincFive

ZincFive BC Series Manual de usuario

BPC

BPC 1.5K SMART Manual de usuario

IBM

IBM 5595-1AX Manual de usuario