CyberData 011394 SERIES Manual de usuario
Quick Start Guide 931182A
The IP Endpoint Company
1.0 Out-of-Box and Prior to Final Installation
1.1. Verify that you have received all of the parts listed on the Installation Quick
Reference placemat.
1.2. Download the current manual, otherwise known as an Operation Guide,
which is available in the Downloads tab at the following webpage:
http://www.cyberdata.net/voip/011393/
Note You can also navigate to the Downloads tab by going to
www.CyberData.net and following the steps that are indicated by
the following figures:
2.0 Select Power Source
PoE Switch PoE Injector
Set PoE power type to Class 0 = 15.4W CAT6 cable recommended—
for longer distances
Be sure you are using a non-PoE switch or port
Make sure port is not in trunk mode
Set port to full duplex/ 100mbps
Spanning Tree Protocol (STP) must be disabled or Portfast enabled
1
34
2
SIP Speaker
Part Numbers: 011393 (RAL 9002, Gray White)
011394 (RAL 9003, Signal White)
SIP Speaker
Quick Start Guide
Quick Start Guide 931182A
3.0 Power Test
3.1. Plug in the CyberData device and monitor the LED activity on the front of
the device. See the following figure:
3.2. The GREEN power/status LED and the YELLOW network LED come on
immediately. The YELLOW network LED will blink to indicate network traffic.
After about 27 seconds, the GREEN power/status LED will blink twice to
indicate that the board is fully booted.
If there is no DHCP server available on the network, it will try 12 times with a
three second delay between tries and eventually fall back to the
programmed static IP address (by default 10.10.10.10). This process will
take approximately 80 seconds.
3.3. When the device has completed the initialization process, press and hold
the RTFM switch for 3 seconds to announce the IP address.
This concludes the power test. Go to Section 4.0, "Connecting to a Network
in a Test Environment".
Speaker
Status
(Green LED)
Network
Link/Activity
(Yellow LED)
Quick Start Guide 931182A
4.0 Connecting to a Network in a Test Environment
Note The following connections are usually needed for this procedure:
• Computer
• PoE switch or injector
• CyberData device
4.1. In a test environment, use a computer that is connected to the same switch
as a single CyberData device. Note the subnet of the test computer.
4.2. Use the CyberData Discovery Utility program to locate the device on the
network. You can download the Discovery Utility program from the following
link:
http://www.cyberdata.net/assets/common/discovery.zip
4.3. Wait for initialization to complete before using the Discovery Utility program
to scan for a device. The device will show the current IP address, MAC
address, and serial number.
4.4. Select the device.
4.5. Click Launch Browser. If the IP address is in a reachable subnet from the
computer that you are using to access the device, the Discovery Utility
program should be able to launch a browser window pointing to the device’s
IP address.
4.6. Log on to the web interface by using the default username (admin) and
password (admin) to configure the device.
4.7. Perform an audio test by pressing the Test Audio button that is located at
the bottom of the Device Configuration page. If the audio test message is
clearly audible, then your CyberData device is functioning properly.
4.8. The device is now ready to be set for your desired network configuration.
You may search the Compatible IP-PBX Servers index for available
sample VoIP phone system configurations and set up guides at the following
website address:
http://www.cyberdata.net/connecting-to-ip-pbx-servers/
Quick Start Guide 931182A
5.0 Contacting CyberData VoIP Technical Support
We encourage you to access our Technical Support help desk at the following
address:
http://support.cyberdata.net/
Note You can also access the Technical Support help desk by navigating through
menus on the CyberData website (www.CyberData.net) as shown in the
following figure:
The Technical Support help desk provides the options of accessing
documentation for your CyberData product, browsing the knowledge base, and
submitting a troubleshooting ticket.
Please be advised requests for Returned Materials Authorization (RMA) numbers
require an active VoIP Technical Support ticket number. A product will not be
accepted for return without an approved RMA number.
Otros manuales para 011394 SERIES
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Oradores de CyberData
CyberData
CyberData 011505 Manual
CyberData
CyberData 011523 Manual
CyberData
CyberData 011487 Manual
CyberData
CyberData 11180 Manual de usuario
CyberData
CyberData 010844D Manual de usuario
CyberData
CyberData 011399 Manual de usuario
CyberData
CyberData 011098A Manual de usuario
CyberData
CyberData 11180 Manual
CyberData
CyberData 011396 Manual de usuario
CyberData
CyberData 011487 Manual de usuario
CyberData
CyberData 011402 Manual
CyberData
CyberData 10844 Manual de usuario
CyberData
CyberData 011402 Manual
CyberData
CyberData VoIP V2 Manual de usuario
CyberData
CyberData 011458 Manual
CyberData
CyberData 10844 Manual de usuario
CyberData
CyberData 011401 Manual
CyberData
CyberData InformaCast 011521 Manual
CyberData
CyberData 11098 Manual de usuario
CyberData
CyberData 011504 Manual
