Curtis 906 Manual de usuario
MODEL 906
Battery “Fuel” Gauge
Read Instructions Carefully!
®
SAFETY INSTRUCTIONS
This instrument was manufactured and tested according to the
applicable technical standards. It complies with all the safety
regulations as shipped from the factory.
Installation and startup must be performed by skilled personnel.
Failure to install and operate the unit in accordance with these
instructions may result in damage or injury.
If safe operation of the instrument can no longer be ensured,
stop and secure it against accidental operation.
If instrument failure or malfunction may cause personal injury
or material damage, use additional safety measures such as
limit switches, guards, etc.
Read the Operating Instructions carefully before startup.
Note the safety instructions marked with this
warning symbol in this manual!
TABLE OF CONTENTS
1. Model Encodement 2
2. Technical Specifications
2.1 Electrical 6
2.2 Mechanical 6
2.3 Environmental 7
3. Installation 8
4. Operation
4.1 Display 9
4.2 Reset 10
5. Troubleshooting 11
6. Maintenance 12
7. Warranty 13
2
Example: Model 906 D 24 M C D A O
Case Style
Voltage
Reset
Discharge
Output
Special
Options
1 3 5
2 4 6
Artwork
7
Case Style Options
1
12
24
36
48
Voltage
Options
2
1. MODEL ENCODEMENT
D DIN case – rectangular
F Hex bezel w/1/4” spade terminals (enGage I)
J Hex bezel w/Packard connector (enGage I)
N DIN case - rectangular, snap-fit
P Pin mount (module)
R 52mm Round bezel & case (same as 700Q)
T Hex bezel w/3/16” spade terminals (enGage I)
TX Hex bezel w/3/16” spade terminals (old T case)
Y Rectangular bezel w/Packard connector (enGage I)
Z Rectangular bezel w/1/4” spade terminals (enGage I)
3
Reset Profile Options
3
Profile with
Memory Option
Profile without
Memory Option
Volts per Cell
OCR HVR CTR Full CTR
Empty
K 1.928 2.167 2.167 2.10
J N/A 2.167
Y 2.083 2.167 2.167 2.10
N 1.980 2.230 2.230 2.10
E N/A 2.230
T 2.028 2.280 2.28 2.10
L N/A 2.280
D 2.060 2.320 2.32 2.10
P N/A 2.320
B 2.090 2.350 2.35 2.10
H N/A 2.350
C 2.135 2.400 2.400 2.10
M N/A 2.400
F N/A 2.416
4
Discharge Profile Options
4
Note: This gauge is not intended to measure the state-of-charge of batteries
subject to extended periods of inactivity since it does not account for self-
discharge effects. Consult factory for details.
Letter Code Volts per Cell
Full Empty
G 1.97 1.75
H 1.97 1.70
J 1.97 1.63
K 2.01 1.65
L 2.10 1.92
M 2.00 1.83
N 2.04 1.73
P 2.08 1.98
Q 2.10 1.88
R 2.02 1.90
S 2.08 1.85
T 2.03 1.90
V 1.98 1.85
W 2.02 1.85
X 1.95 1.75
Y 2.00 1.90
5
Letter Code Logo
O Curtis
N None
Special Options
A = (TBD)
Output Options
5
6Artwork Options
7
Letter
Code Signal
ANo option
B1Both output & memory options
C1Both output & memory options and CTR reset instead of HVR
DOutput option only
MMemory option only
1 option is for micro versions only
6
2. TECHNICAL SPECIFICATIONS
2.1 Electrical Operating Voltage
Operating Range: ±25% of nominal voltage
Operating Current
2.2 Mechanical Display
10-digit
Red LED
Tri-color (5 green, 3 yellow, 2 red)
Voltage
(VDC)
Nominal Current
(mA)
Maximum Current
(mA @B++25%)
12 23 38
24 17 24
36 16 22
48 16 21
7
Recommended Panel Cutouts
F, J, T, TX, Y, Z Cases: 36.8 mm x 24.1 mm
+0.3/-.0mm
D, N Cases: 45.3 mm x 22.3 mm ±0.1
R Case: 52.4 mm
Terminals
D, N, T, TX: 3/16” blade
R, F, Z: 1/4” blade
J, Y: 4-pin Packard Connector equivilent to
Delphi PN 15336035
P: Solder pins
2.3 Environmental Temperature
Operating: –40 to +85°C
Storage: –50 to +90°C
Humidity: 95% RH non-condensing at 38°C
Shock and Vibration: Meets SAE J 1378
8
3. INSTALLATION
Connecting Model 906
Pin 1 = Battery +
Connects to the vehicle’s main positive (+) terminal.
Use as short a wire as practical.
Pin 2 = Battery –
Connects to the vehicle’s main negative (–) terminal
Use as short a wire as practical.
Note: Pins 1 & 2 are connected across the total
battery pack.
Pin 3 = Output Signal + or No Option
Output Signal option: 5 VDC ±0.5 VDC (90 µA
current source) above Empty, 0-0.1 VDC at Empty
1 VDC maximum (90 µA sink);
No Option: Pin 3 is left open.
Pin 4 = Keyswitch
Connects to Battery + through the switched terminal
of the keyswitch.
Tabla de contenidos
Otros manuales de Instrumento de medición de Curtis
Curtis
Curtis 803 Manual de usuario
Curtis
Curtis Acuity 1030 Manual de usuario
Curtis
Curtis 700 series Manual de usuario
Curtis
Curtis enGage II 3000 Series Manual de usuario
Curtis
Curtis 700 series Manual de usuario
Curtis
Curtis enGage III 3000 Series Manual de usuario
Curtis
Curtis enGage II 3000 Series Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario