curt 18087 Manual de usuario
Item# Qty Description
1 1 Main body rack arms
2 1 Extension rack arms
3 1 Hitch mounting shank
4 4 Support arm
5 4 Support arm
6 2 Locking arm, short (SL,SR)
7 2 Locking arm, long (LL, LR)
8 6 Pan head screw, M6 - 10mm
9 2 Spacer
10 1Clip
11 1Anti-rattle bolt set, 1/2" - 96mm
12 1Shank bolt set, 1/2" - 76mm
13 2Extension bolt set, 1/2" - 60mm
14 1Metric wrench
15 1Allen wrench, M8
16 2Key set
4 5
6
(SL, SR)
7
(LL, LR)
8 9 10 11 12 13 14 15
16
3
1
2
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
INSTALLATION INSTRUCTIONS
PARTS LIST
TRAY-STYLE BIKE RACK
WARNINGS
This product is not intended for
off-road use, tandems or recumbents.
Do not install on a trailer or other towed vehicle.
Check tightness of all bolts periodically.
Never use bike rack with a hitch extender.
The provided anti-rattle bolt must be threaded
completely through the vehicle's receiver tube and
tightened to 75 ft. lbs. If not completely tightened,
the bike rack can shake, rattle, rock and vibrate.
This could potentially cause damage to the bikes.
PAGE 1 • 18087-INS-RD • 1.800.798.0813 • NEED ASSISTANCE? • CURTMFG.COM
Step 1
Remove security pins from shank (#3). Insert spacers (#9) into the inside of hitch mounting shank (#3) as shown in Figure 1,
Detail A. After spacers are inserted, place the main body rack (#1) into shank (#3) and secure with the two security pins
(previously removed) and shank bolt (#12) as shown in Detail B. Tighten bolt using wrenches provided (#14, #15). See Detail C.
AS S E MB LY
Detail A
Detail B
Detail C
Figure 1
CURTMFG.COM • NEED ASSISTANCE? • 1.800.798.0813 • 18087-INS-RD • PAGE 2
Step 2
Remove the outer arm pins & clips from main body rack (#1). See Figure 2, Detail D. Drop the side arms
down to until they lay flat, see Figure 2. Re-insert the security pins & clips to secure in place, see Detail E.
AS S E MB LY
Figure 2
Detail D Detail E
PAGE 3 • 18087-INS-RD • 1.800.798.0813 • NEED ASSISTANCE? • CURTMFG.COM
Step 3
Slide on two of each support arm (#4, #5) onto the main body rack (#1) arms, making sure the tightening
knob is facing upward. See Figure 3. Tighten the knobs as shown in Figure 4, Detail F. After the supports are
tightened, insert pan head screw (#8) into the end of each arm as shown in Figure 4, Detail G.
Figure 3
Figure 4
Detail F
Detail G
AS S E MB LY
CURTMFG.COM • NEED ASSISTANCE? • 1.800.798.0813 • 18087-INS-RD • PAGE 4
Step 4
Slide the long locking arm (#7) onto the middle arm of the main body rack (#1), making sure the locking arm is facing
the mounting shank (#3). Repeat this process with the short locking arm (#6). See Figure 5, Details H. Press hooks
down onto bike frame until it makes contact and then press down firmly until you hear one to two additional clicks
from the ratchet system. After the locking arms are installed, insert pan head screw and lock washer (#8) into the
end of the center post as shown in Figure 5, Detail I.
Figure 5
Detail H
Detail H
Detail I
AS S E MB LY
PAGE 5 • 18087-INS-RD • 1.800.798.0813 • NEED ASSISTANCE? • CURTMFG.COM
INSTALLATION
To install your bike rack on your vehicle, slide the shank into your receiver hitch tube opening
(see Figure 6, Detail J) and secure with the anti-rattle bolt (#11) (see Detail K) and clip (#10) (see Detail L).
WARNING: Anti-rattle bolt must be threaded completely through the vehicle's receiver tube and tightened to 75 ft. lbs.
If not completely tightened, the bike rack can shake, rattle, rock and vibrate. This could potentially cause damage to the bikes.
Detail K Detail L
Figure 6
Detail J
CURTMFG.COM • NEED ASSISTANCE? • 1.800.798.0813 • 18087-INS-RD • PAGE 6
Figure 7
Detail M
ASSEMBLE AND INSTALL THE 2-BIKE EXTENSION
7 (SR)
6 (SL)
To assemble
Assemble the extension following steps 2 through 4 in the 'Assembly' section using the extension rack arms (#2).
To install
Insert shank of extension rack (#2) into the open shank of the main body rack (#1).
Secure using both extension bolt sets (#13). See Figure 7, Detail M.
PAGE 7 • 18087-INS-RD • 1.800.798.0813 • NEED ASSISTANCE? • CURTMFG.COM
USE
Figure 8
Load the heaviest bike onto rack set closest to the vehicle. Raise the long lock arm (#7) to get the bike cross beam
underneath it. Once bike is in place, lower the locking arm down onto the crossbar. See Figure 8, Detail N.
Detail N
CURTMFG.COM • NEED ASSISTANCE? • 1.800.798.0813 • 18087-INS-RD • PAGE 8
REAR VEHICLE ACCESS
Figure 9
Remove the security pins from the base of the bike rack and replace them in the top hole of the base plate so the carrier
does not tip too far down. See Figure 9, Detail O. Tilt the carrier down until it is supported by the security pins. See Figure 9.
Detail O
PAGE 9 • 18087-INS-RD • 1.800.798.0813 • NEED ASSISTANCE? • CURTMFG.COM
TRAVEL STORAGE: OPTION 1
Remove the outer arm pins & clips from the base's face plates. See Figure 10, Detail P.
Raise side arms up and replace the pins to secure into place. See Detail Q.
Figure 10
Detail P Detail Q
CURTMFG.COM • NEED ASSISTANCE? • 1.800.798.0813 • 18087-INS-RD • PAGE 10
Tabla de contenidos
Otros manuales de Accesorios para automóviles de curt
curt
curt Spectrum 51170 Manual de usuario
curt
curt 13490 Manual de usuario
curt
curt 60607 Manual de usuario
curt
curt CM 18031 Manual de usuario
curt
curt 45952 Manual de usuario
curt
curt 13454 Manual de usuario
curt
curt 58909 Manual de usuario
curt
curt 70130 Manual de usuario
curt
curt 18112 Manual de usuario
curt
curt 25470 Manual de usuario
curt
curt 11354 Manual de usuario
curt
curt CM-58967 Manual de usuario
curt
curt 12142 Manual de usuario
curt
curt 17510 Manual de usuario
curt
curt 45832 Manual de usuario
curt
curt 18410 Manual de usuario
curt
curt 13119 Manual de usuario
curt
curt R16 5TH Manual de usuario
curt
curt 16028 Manual de usuario
curt
curt 57009 Manual de usuario
