CURRENT Luxury SilenTrac Manual de usuario
1
Installation Guide
www.currentluxury.com
1-844-307-7435
service@currentluxury.com
1
2
Drapery Track Installation
For additional help during installation of your drapery track, visit www.currentluxury.com or call 1-844-307-7435.
For proper installation of your track drapery, the following tools are required:
1/4” nut driver
5/64” hex screwdriver (spliced tracks only)
6” magnetic bit holder extension for drill
Tape measure
Drill
Level
Pencil
Ladder
7/64” drill bit for stud applications
1/4” drill bit for drywall applications with toggler anchors
#2 Phillips Screwdriver
Stud Finder (optional)
Flathead Screwdriver (optional)
Vacuum Cleaner
Safety Goggles
Track (Right draw shown) Carriers (installed)
Carrier Arm(s)
Return Clips
Primary Motor
Secondary Motor
Pendant
Brackets
Sensor Box
Fascia
Fascia Clips
Fascia Spacers (for ceiling mount)
Track Splice
Figure 3.1 - Slide the splice over and tighten.
Figure 2.2 - Insert Retaining Plate
I. Splicing the Track
If your track is UNSPLICED, proceed to Section 2: Drapery Track Installation
1. Unpack the Track
1.1 - Remove track from plastic and take out the foam block inside
the track that secures the belt.
NOTE: On any spliced track over 12’ in length, be sure to use two or more people to lift the track to prevent bending the splice.
Do not pick up any spliced track upside down or the splice will bend.
1.2 - With the track positioned upside down (carriers pointed up),
apply tension to the belt by gripping both pieces of the
master carrier and pulling them together as you straighten the
track sections. This will help prevent the belt from coming out of
the channels.
2. Install Master Carrier Retaining Plate
2.1 - With the straighten track remaining upside down,
continue moving the master carrier pieces towards each
other while unfolding the track sections.
2.2 - Insert the master carrier retaining plate into both
plastic sections. On center draw applications, do this for both
master carriers.
2.3 - On tracks with string carriers be sure the metal master
carrier retaining plate is oriented correctly to ensure a fit over the
inserted string end.
3. Secure Splice
3.1 - Flip the track on its side, so that the top of the track is
facing towards you. The metal track splice will be inserted into
one side of the track.
3.2 - Loosen the four set screws in the splice using the provided
tool, then slide the splice over the joint where the halves come
together. Maintain good alignment and tighten the four set screws.
Do not over tighten.
4. Assemble the Master Carrier and Arms
4.1 - Using the diagram inserted with this manual, assemble the master carrier by affixing the wheeled carrier attachment and
carrier arm to the master carrier. Use the provided screws to retain all pieces together.
cOn enter draw applications, be sure to do this for both master carriers.
On side draw applications, be sure the arm is facing the full close direction of the track.
Figure 1.1
Figure 1.2
3
4
Double check drapery height, drapery width, and track length before beginning your installation. Drapery track must be level
and all brackets must be vertically aligned for track to function properly.
NOTE: If your track is spliced, follow the splicing instructions for proper assembly.
1. INSTALL THE BRACKETS
1.1 - Install the outer brackets first. Locate the center of the outer brackets 6” from each end of the track. See Figure 2.1.1
(If the drapery is center draw, use the centerline of the window opening as a reference. For side draw applications, adjust track
position if necessary to accommodate for drapery stackback.)
Figure 2.1.1 - Bracket Placement
2. DRapery Track Installation
1.2 - Evenly space the remaining brackets every 16”-36” (for dual tracks, additional brackets will be required). See bracket chart
on page 3.
For wall mount applications, use the following formula to determine
bracket mounting height. Install brackets using “bottom side” as
reference point.
BH = TE + DH + BC
- BH = Bracket Height
- TE = Track Exposure
- DH = Drapery Height
- BC = Bottom Clearance
For ceiling mount applications with fascia, use the provided spacers.
BH
TE
DH
Figure 2.1.2 - Calculate bracket installation height
BH = TE + DH + BC
Bottom Side
Bottom
Side
6” Every 16” - 36”
Every
16”- 36”
6”
6” Every 16” - 36” 6”
6” 6”
6”
6”
6” 6”
BC
5
Figure 2.1.3- Be aware of pin setting differences
Be aware of the desired pin setting, as the track exposure may be
a negative number for front mount applications. See Figure 2.1.3. Front Mount
Pinch Pleat
Under Mount
Pinch Pleat
Pin Ripple
Ripplefold
Pro Tip: Use a laser level to make sure the brackets are installed in a straight line for both ceiling and wall mount applications.
Figure 2.1.4
Use the following guidelines when installing the drapery track to the wall or ceiling.
Brackets Included by Length
Track Length Number of Brackets
Up to 30"
31" - 60"
61" - 90"
91" - 120"
121" - 150"
151" - 180"
181" - 210"
211" - 240"
3
4
5
6
7
8
9
10
241" - 270"
271" - 300"
301" - 330"
11
12
13
331" - 360"
361" - 396"
14
15
397" - 432" 16
The brackets at each end must be located no more than 6 inches from either end of the drapery track, additional bracket
is required at motor end to accomodate additional pull force from Pendant.
If no structural member is present at each bracket location, an anchor suitable for the weight of the drapery, drapery
track, and motor must be used.
Each remaining bracket should be evenly spaced across the remainder of the drapery track.
Heavier drapery panels may require additional brackets.
On standard panels, use the center bracket to screw directly into the splice. On heavier drapery panels, mounts should
be placed 6 to 8 inches away from either side of the splice seam.
Refer to anchor manufacturers pull out forces recommendation.
Contact Current Products Corp. customer service for assistance in calculating pull out forces.
6
Figure 2.2.1 - Camlock in open position
Figure 2.2.2 - Push the track up and tighten camlock.
Figure 2.2.3 - Screw into splice or place brackets on either side
of splice.
2A. INSTALL THE TRACK
2.1 - Begin with the camlocks in the open position. See Figure 2.2.1.
If using fascia, install fascia clips before track installation.
For ceiling mount installations be sure the return clips are installed
prior to installation of the track to the camlocks.
2.2 - On unspliced tracks, starting in the middle, secure the track
onto each of the brackets using the camlock. For center draw
applications, align the centerline of the track with the centerline of
the window opening.
To lock, twist camlock arm clockwise. See Figure 2.2.2.
2.3 - If your track is spliced, either:
Screw the center bracket screw into the center hole in the splice,
loosening and retightening the set screws to adjust splice placement
if necessary.
Or if using heavy curtains, place one bracket 8 inches to the left, and
one bracket 8 inches to the right of the splice seam.
See Figure 2.2.3.
2.4 - For wall mount applications, once all the camlocks are closed,
use a Phillips Head screwdriver to tighten each camlock.
7
Figure 2.3.2 - Add or remove pin carriers
Figure 2.3.3 - Add or remove string carriers
3. ADJUST NUMBER OF CARRIERS
3.1 - It may be necessary to add or remove carriers based on the
curtain size, fullness, and pleat spacing. To add or remove carriers,
remove the motor if it is installed. Then, loosen the hardstop screw
and slide it out of the track. See Figure 2.3.1.
3.2 - For loose carriers, insert or remove carriers until the
correct amount remain in the track. Center draw applications
may require adding or subtracting carriers from each side.
See Figure 2.3.2.
3.3 - For carriers that are strung together, the entire string will
need to be changed if more or less carriers are desired (dictated
by carrier string spacing). Contact Current Products Corp.
customer support for details. See Figure 2.3.3.
Figure 2.3.1 - Remove hardstop
4. CONNECT THE MOTORS
4.1 - On a single drapery, insert the Primary motor shaft onto the
motor end of the drapery track and twist the motor into place.
Motor is not secure until you hear a click. See Figure 2.4.1.
Figure 2.4.1 - Attach motor
Figure 2.4.2 - Attach primary motor
Figure 2.4.3 - Attach secondary motor
4.2 - On a dual drapery, insert the Primary motor shaft onto the motor
end of the window side drapery track and twist the motor into place.
Motor is not secure until you hear a click. See Figure 2.4.2.
Insert the Secondary motor shaft onto the motor end of the room
side drapery track and twist the motor into place. Motor is not secure
until you hear a click. See Figure 2.4.3.
Figure 2.4.4 - Plug secondary motor into primary motor
Orienting the plug correctly, plug the cord from the Secondary
motor into the bottom of the Primary motor. If you have a Sensor
box, proceed to Step 5. See Figure 2.4.4.
8
On a single drapery, plug the Primary motor into the Motor 1 slot.
See Figure 2.5.2.
Figure 2.5.2 - Motor plugged into slot
Figure 2.5.3 - Two motors plugged into slots
On a dual drapery, plug the Primary motor into the Motor 1 slot
and Secondary motor into the Motor 2 slot. See Figure 2.5.3.
5. CONNECT THE SENSOR BOX (Optional)
Install the sensor box behind the drapery in a place where the Pendant is still accessible and the sensors will still detect light
coming in from the window.
Figure 2.5.1 - Attach sensor box to wall
Screw the wall plate into the desired location, using wall anchors
if necessary, then slide the sensor box over the plate until it sits
securely. See Figure 2.5.1.
9
6. ATTACH THE DRAPERY
6.1 - Snap or hook the drapery into each carrier starting with the
master carrier arm and ending with the hardstop and control end.
See Figure 2.6.1.
If using Pin Ripple, be sure the first carrier gets pinned away from
the carrier arm, then alternate pin directions on each carrier.
Figure 2.6.1 - Hook or snap drapery onto carriers
Figure 2.6.2 - Return Clip placement options
6.2 - If desired, snap in the return clips and pin return through the
openings. See Figure 2.6.2
Figure 2.6.3- Screw in eyelet then insert pin through the opening
6.3 - If desired, screw the provided eye hook into the wall where the
last pin will go, then insert the pin through the eyelet. See Figure
2.6.3.
You are now ready to start up the drapery track.
7. ATTACH THE BATON (Optional)
7.1 - If using the font baton, the plastic reinforcer must be sewn
into the drapery and the grommet punched in advance of drapery
installation.
For front mounted baton, slide the plastic wedge through the slat
in the carrier arm. Place the plastic baton hook over the grommet
and screw in the screw to secure. See Figure 2.7.1. Figure 2.7.1 - Front mount baton components and install order
Figure 2.7.2 - Hook back baton into carrier arm eyelet
7.2 - For a back mounted baton, locate the eyelet under the carrier
arms and connect the baton with a clip. See Figure 2.7.2.
1
2
3
4
10
Otros manuales para SilenTrac
1
Tabla de contenidos
Otros manuales de Persiana de ventana de CURRENT Luxury
Manuales populares de Persiana de ventana de otras marcas
Domondo
Domondo PureNight Manual de instrucciones de instalación
rollease acmeda
rollease acmeda Easy Spring Air Guía de configuración
IKEA
IKEA KADRILJ Manual de usuario
Hallis Hudson
Hallis Hudson Rolls Super glide Manual de usuario
Benthin
Benthin P1614 Manual de usuario
MV LINE
MV LINE CLARA 015 Manual de instrucciones
