CTS ESW-3128 Series Manual de usuario

ESW-3128 Series

24 PORTS 10/100/1000BASE-T RJ-45 WITH 4

COMBO PORTS (10/100/1000BASE-T,

100/1000BASE-X SFP) UPLINK MANAGEMENT

SWITCH

User’s Guide

Version 0.91

FCC Warning

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with this user’s guide, may cause harmful interference

to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to

correct the interference at their own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause

radio interference in which case the user may be required to take adequate

measures.

Trademarks

CTS is a registered trademark of Connection Technology Systems Inc

All trademarks belong to their respective proprietors.

Contents are subject to change without prior notice.

This publication may not be reproduced as a whole or in part, in any way

whatsoever unless prior consent has been obtained from Connection

Technology Systems Inc.

Revision History

Version

Date

Description

0.90

20150610

First release

0.91

20150720

Key Feature Rearrangement

Table of Contents

1. INTRODUCTION ...........................................................................................5

1.1 The Managed Switch................................................................................5

1.2 Key Features............................................................................................6

1.3 Front & Rear Panel...................................................................................7

1.4 Cable Specifications.................................................................................7

1.5 Network Management ..............................................................................8

2. INSTALLATION...........................................................................................10

2.1 Requirement...........................................................................................10

2.2 Checking the Package Contents ............................................................10

2.3 Install the Managed Switch..................................................................... 11

2.4 Power ON...............................................................................................12

2.5 Connect the Switch to network...............................................................14

3. OPERATION................................................................................................15

3.1 LED Definitions.......................................................................................15

4. MAINTENANCE ..........................................................................................16

4.1 Fault Identification ..................................................................................16

4.2 Hardware Replacement Procedures ......................................................18

4.3 Firmware Upgrade..................................................................................18

1. INTRODUCTION

The Managed Switch is designed to meet the emerging FTTX & Metro Ethernet

requirement. Its low profile appearance with 1U height and standard rack-

mount size achieves the highest density within a single rack. When massive

fiber ports need to be deployed, the Managed Switch provides the best

performance and price ratio.

1.1 The Managed Switch

This Managed Switch is compact 19-inch, rack mountable, has 24 ports

10/100/1000Base-T RJ-45 with 4 combo ports (10/100/1000Base-T,

100/1000Base-X SFP) in front panel. This Managed Switch provides high

performance store and forward switching capability plus other advanced

features such as QoS, VLAN, etc.

Clear, at-a-glance per-port LED indicators make users easier to control and

manage network status. Built-in management module also allows users to

configure, control and monitor the system locally via console or remotely via

SNMP based management system.

This Managed Switch is a typical suit for the Metro Ethernet application. Its

low profile appearance with 1U height achieves the highest density and can be

used in closet wiring or used as a desktop switch.

1.2 Key Features

19 inch, 1U high

24 x 10/100/1000Base-T ports

-IEEE 802.3/802.3u/802.3ab/802.3z compliance

-Support Auto-Sensing for fiber ports

-Support MDI/MDIX/Auto-Crossover

-RJ-45 Ports

4 x 10/100/1000Base-T ,100/1000Base-X Combo ports

-IEEE 802.3ab/802.3z

-Support Auto-Negotiation (RJ-45) and Auto-Sensing (SFP)

-Support MDI/MDIX/Auto-Crossover

-RJ-45 or SFP Slot

Switching Features

-Store & forward switching

-Non-blocking switching fabric : 56Gbps

-Mac address table:16K

-Memory buffer total 1536K bytes

-VLANs support up to 2K VLAN Groups

-Support jumbo frame on all ports up to 9K bytes size

-QoS classification based on IEEE802.1p, VID, TOS/DSCP, Ethertype

and L4 port.

-Q-in-Q VLAN double tag

-Rate limit control

-SNTP time server

-Static multicasting

-IGMP v1/v2 snooping

-IGMP fast leave

-IGMP filtering via filtering profile

-Multicast channel limitations per port

-Multicast VLAN Register (MVR) **

-DHCP snooping

-DHCP client and auto-provision

-DHCP relay agent with option 82

-Access Control List (ACL)

Management Functions

- Console

- Telnet

- Web

- RADIUS authentication

-SNMP v1/v2 and network management

-SNMP Power-Down Trap

-Private, RFC-1213, RMON MIBs

-Port mirroring

- FTP, TFTP, HTTP server and client firmware upgrade

**Coming Soon

1.3 Front & Rear Panel

Front Panel

The front panel is configured as follows:

1. 24 x 10/100/1000Base-T RJ-45 ports (Ports 1-24)

2. 4 x Gigabit combo ports (Ports 25-28) :

4 x 10/100/1000Base-T RJ-45 ports, or

4 x 100/1000Base-X SFP ports

3. Reset Button:

Pressing reset button for 2 seconds then release to restart the

system.

Pressing reset button for 10 seconds then release to reset the

Managed Switch back to factory settings and restart the system.

4. Console port:

An asynchronous serial console port supporting the RS-232

electrical specification. The console port can be used to

manage the device and the interface should be configured to

9600 , N , 8 ,1

5. LED:

Please refer to chapter 3.1 LED Definitions

Rear Panel

The Managed Switch provides one fixed power module or two power modules

for redundancy purpose. Depending on your physical environment

requirements, the type of power module is selectable and could be either AC

input or DC input.

The rear panel is configured as follows:

Power module and Connector:

AC power connection: 100-240V , 50/60Hz

DC power connection: 48VDC

Please refer to chapter 3.1 LED Definitions

1.4 Cable Specifications

The following table contains various cable specifications for the Managed

Switch. Please make sure that you use the proper cable when connecting the

Managed Switch.

Cable Type

Description

10Base-T

UTP Category 3, 4, 5 (100 meters max.)

EIA/TIA- 568 150-ohm STP (100 meters max.)

100Base-TX

UTP Cat. 5 (100 meters max.)

EIA/TIA-568 150-ohm STP (100 meters max.)

1000Base-T

UTP Cat. 5e (100 meters max.)

UTP Cat. 5 (100 meters max.)

EIA/TIA-568B 150-ohm STP (100 meters max.)

100BASE-FX

Multi-mode fiber module(2km) / Single-mode fiber module

1000BASE-SX

Multi-mode fiber module (550m)

1000BASE-LX

Single-mode fiber module (10km)

1000BASE-LH

Single-mode fiber module (30km/50km)

1000BASE-ZX

Single-mode fiber module (80km)

Mini-GBIC

SFP Transceiver for 1000BASE-SX Multi-mode fiber module (550m)

SFP Transceiver for 1000BASE-LX Single-mode fiber module (10km)

SFP Transceiver for 1000BASE-LH Single-mode fiber module

(30km/50km)

SFP Transceiver for 1000BASE-ZX Single-mode fiber module (80km)

1.5 Network Management

This Managed Switch is Plug & Play compliant. Real-time operational status

can be monitored through a set of LED indicators located in the front panel.

Built-in management module also allows users to configure, control and monitor

the system remotely.

Following is a list of management options available in this Managed Switch:

Local Console Management

Telnet Management

SNMP Management

Web Management

Local Console Management

Users may connect a Terminal or PC with Terminal Emulation program, to the

Managed Switch RJ-45 port directly via RS-232 cable to configure, control and

monitor the system. This is often referred as Out-Of-Band management.

Console management is useful when there is no network connection to the

Switch, for instance configuring the Managed Switch for the first time.

Telnet Management

Telnet is done through the network. Once there is a network connection to the

Managed Switch, users can use Telnet to configure, control and monitor the

system. Using network connection to manage is often referred to In-Band-

Management.

SNMP Management

SNMP is also In-Band-Management and requires a network connection to the

Managed Switch. The Managed Switch private Management Information Bases

(MIB) is provided for SNMP-based network management program to configure,

control and monitor the system.

Web Management

Web Management is done over the network. Once the Managed Switch is

available on the network, you can login and monitor the status of it through a

web browser remotely or locally. Local console-type Web management,

especially for the first time use of the Managed Switch to set up the needed IP,

can also be done through one of the 10/100/1000Base-T 8-pin RJ-45 ports

located on the front panel of the Managed Switch. Direct RJ-45 LAN cable

connection between a PC and the Managed Switch is required for this

management.

Please refer to the Network Management User’s Manual for the detailed

management functions and required installation and operation procedures.

2. INSTALLATION

To properly install the Managed Switch, please follow the procedures listed

below. These procedures are described below in separate sections.

Installation Requirements

Unpacking the Managed Switch

Installing the Managed Switch

Power on the Managed Switch

Connecting the Managed Switch to the network

2.1 Requirement

Basic requirements for installation are as follows:

Environmental conditions

-One power outlet

-Proper ventilation

-Proper isolation to electrical noise, radio, etc.

-UTP cables should not run in the same duct with power and

phone line cables

Required SFP Transceiver or UTP cables

Rack mounting tools

2.2 Checking the Package Contents

Unpack the package carefully and check the package contents. The package

should contain the following items:

Standard

-One Managed Switch

-Mounting kit: 2 mounting brackets and screws (Fixed in the

Managed Switch when shipped)

-Four rubber feet with adhesive backing

-Console RS-232 cable with RJ-45 connector

-Documentation CD

-AC power cord (For AC power module only)

Tabla de contenidos

Otros manuales de Cambiar de CTS

CTS

CTS EPS-3112 Manual de usuario

CTS

CTS FOS-3114 Series Manual de usuario

CTS

CTS IPS-3006 Series Manual de usuario

CTS

CTS HES-5106 Series Manual de usuario

CTS

CTS FOS-3126-PLUS SERIES Manual de usuario

CTS

CTS FOS-3124-BAT-II Series Manual de usuario

CTS

CTS SWH-2108 Manual de usuario

CTS

CTS ESW-5128 Series Manual de usuario

CTS

CTS FOS-3128 Series Manual de usuario

CTS

CTS HES-3106SFP-F2 Manual de usuario

CTS

CTS ESW-5112-2MG Series Manual de usuario

CTS

CTS IES-3106 Series Manual de usuario

CTS

CTS EPS-2006 Manual de usuario

CTS

CTS IES-3006 Series Manual de usuario

CTS

CTS IPS-3120-PoE++ Manual de usuario

CTS

CTS WPS-2006 Series Manual de usuario

CTS

CTS HES-3106-PLUS Series Manual de usuario

CTS

CTS SWH-2109FX Manual de usuario

CTS

CTS FOS-3110 Series Manual de usuario

CTS

CTS EPS-3128 Series Manual de usuario

CTS

CTS HES-3109 Series Manual de usuario

CTS

CTS FOS-5126 Series Manual de usuario

CTS

CTS FOS-5112 Manual de usuario

CTS

CTS WAS-2006 Series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario