Croydex HENDERSON MM8300 E Series Manual

MIR 038 R06

MM8300##E

HENDERSON LED

ILLUMINATED MIRROR

500 X 700 X 37mm

ALL PRODUCT DIMENSIONS DETAILED IN THIS INSTALLATION AND MAINTENANCE

MANUAL ARE APPROXIMATE

ALL ILLUSTRATIONS OF THE PRODUCT ARE FOR REFERENCE ONLY. COMPONENTS

SUPPLIED WITH INDIVIDUAL PRODUCTS MAY DIFFER

CONTACT DETAILS (UK)

Croydex

Central Way

Andover

Hampshire

SP10 5AW

Tel: +44 (0)1264 365881

Email: info@croydex.co.uk

www.croydex.com

CONTACT DETAILS (EU)

MIL

Unit 8 Purcellsinch Ind Est

Dublin Road

Kilkenny

R95 HP71

Ireland

ALWAYS CHECK THE PACKAGING FOR FIXINGS AND PARTS BEFORE RECYCLING OR

DISPOSAL.

PLEASE READ THROUGH AND FULLY UNDERSTAND THE INSTRUCTION LEAFLET BEFORE

STARTING THE INSTALLATION OF THIS MIRROR.

ENSURE YOU HAVE ALL THE FIXINGS AND PARTS BEFORE ATTEMPTING TO ASSEMBLE OR FIT

THIS PRODUCT.

MIR 038 R06

SECTION 1 - INTRODUCTION

Thank you for purchasing this Croydex product. Please follow the ﬁxing and care instructions to

ensure that your product is ﬁtted safely and that it retains its high quality ﬁnish. PLEASE RETAIN

THIS MANUAL FOR FUTURE REFERENCE.

SAFETY & PRODUCT CARE

1. ALWAYS take care when using power

tools, particularly if there is any water in the

working area.

2. ALWAYS wear eye protection when using

power tools.

3. ALWAYS check for pipes and cables

before drilling into walls.

4. ALWAYS use a ceramic drill bit when

drilling into tiled surfaces.

5. ALWAYS use a drill bit that is suitable for

the surface that is being drilled.

6. The wall plugs supplied are for use

on solid walls only. For cavity walls or

plasterboard ALWAYS use specialist ﬁxings

that are suitable for the type of wall

construction.

7. DO NOT use abrasive or chemical

cleaners as these may damage the product.

8. DO NOT strike the mirror with hard or

sharp objects.

9. DO NOT drill on the grout line of tiles.

10. ALWAYS use masking tape on tiles

surfaces.

IMPORTANT INSTALLATION

INFORMATION

THIS IS A CLASS 1 APPLIANCE AND MUST BE

CONNECTED TO EARTH

HAZARDOUS VOLTAGES INSIDE – DO NOT OPEN

SEALED UNITS

THERE ARE NO USER REPLACEABLE PARTS IN

THE MIRROR

In accordance with Statutory Instrument 2004

No. 3210 - The Building (Amendment) (No.3)

Regulations 2004, any work, other than repair/

replacements, in a room where there is water

(e.g. kitchen, bathroom, etc.) must be either:

• Carried out by an electrician who is a

member of a competent person self

certiﬁcation scheme who will certify the

work complies with the Building Regulations

and you do not need to notify your local

authority.

• Carried out after prior notiﬁcation to the

Local Authority Building Control Department,

which has responsibility for ensuring that the

work is inspected and tested.

TOOLS REQUIRED

MIR 038 R06

IMPORTANT WARRANTY INFORMATION

In accordance with Statutory Instrument 2004 No. 3210 - The Building (Amendment) (No.3)

Regulations 2004, the installer must give the occupier of the premises in which this product has

been installed a certiﬁcate to conﬁrm that the requirements of regulations 4 and 7 have been

satisﬁed, or the installation of this product must be inspected and tested by the Local Authority

Building Control Department who will issue a compliance certiﬁcate.

A copy of this certiﬁcate may be required for certain warranty claims. Failure to provide a copy of

the certiﬁcate may invalidate the warranty.

This does not aect your statutory rights

We recommend that you make yourself aware of the Regulations before you undertake any

work and if you require clariﬁcation you should contact your Local Authority Building Control

Department.

POSITIONING THE MIRROR

1. The mirror is rated IP44 and must only be installed with the connection to the domestic

mains electrical supply in the Outside Zones, as shown in Fig. 1.

2. Ensure that the access to the domestic mains electrical supply is located behind the

intended mounting position for the mirror and unobstructed by the mounting brackets.

ﬁg. 1

WALL FIXING PACK

x2 Countersink

Screw

x2 Hang n Lock

Wall Plug

x1 Hang N Lock

Bracket - Left x2 Cam

x2 Toggle Bolts

x1 Wall Plugs

x1 L-Bracket

x1 Pan-Head

Screw

BRACKET

ﬁg.5

MIR 038 R06

SECTION 2 - MOUNTING USING HANG N LOCK

1. Place the Hang ‘N’ Lock bracket onto the

support slot on the back of the mirror. Make a

note of the distance from the bottom edge of

the bracket to the top edge of the mirror - this

will help you when mounting your mirror.

(See Fig. 2)

ﬁg. 2

2. Carefully hold your mirror in the desired

location on the wall. Using a pencil, draw a

reference line along the top edge of the mirror.

Use the bracket distance you measured earlier

to create a reference line where the bottom of

your Hang ‘N’ Lock bracket will be.

(See Fig. 3)

ﬁg. 3

3. Place the bottom edge of the Hang ’N’ Lock

bracket onto the lower reference line. Mark the

hole centres with a pencil.

(See Fig. 4)

Note: Check the cams are oriented

correctly with the countersink holes

positioned at the top.

ﬁg. 4

4. Drill the marked holes to a depth of 45mm.

Insert the wall plugs level with the surface of

the wall. If you are ﬁtting to a tiled surface,

insert the wall plugs below the surface of the

tile to avoid cracking the tiles. Wall plugs

supplied are for use on solid walls only. (See

Fig. 5)

NOTE:

For CAVITY WALLS or PLASTERBOARD

use toggle bolts provided. See SECTION 3 -

Toggle Bolt Installation. Continue to Step

COUNTERSINK

HOLE

Dim. Y

MIR 038 R06

5. Insert the countersink screws through the

Hang ‘N’ Lock cams and loosely secure the

Hang ‘N’ Lock bracket to the wall.

(See Fig. 6)

Note: Check the cams are oriented

correctly with the countersink holes

positioned at the top.

ﬁg. 6

6. With the Hang ’N’ Lock bracket loosely

attached to the wall, adjust for height and

level by rotating the cams with a ﬂat head

screwdriver. Use the attached spirit level as

a guide. Once complete, fully tighten the

mounting screws to securely ﬁx the bracket into

position.

(See Fig. 7)

ﬁg. 7

7. Hang the mirror onto the Hang ‘N’ Lock

bracket. Ensure the mirror has securely located

onto the bracket before letting go.

(See Fig. 8)

Note: If the mirror is not vertical, remove

the mirror, loosen bracket screws and

repeat Step 6.

ﬁg. 8

COUNTERSINK

SCREWS

BRACKET

Note: The position of the

mirror can be adjusted

by sliding left or right

along the bracket.

8. Place the L bracket over the threaded

rivet located at the bottom of the mirror.

Using a pencil mark the position of the L

bracket onto the wall.

(See Fig. 10)

ﬁg. 9

MIR 038 R06

9. Gently remove the mirror, place the L

bracket on the mark and drill a hole in the

centre of the slot on the wall. Insert the wall

plug and lightly screw the bracket to the

wall, allowing the bracket to be moved up

and down the slot.

(See Fig. 10)

ﬁg. 10

10. With the mirror in place, secure the

L bracket to the mirror using the bolt

provided. (See Fig. 12)

ﬁg. 10

* Refer to SECTION 4 - CONNECTING THE ELECTRICAL SUPPLY before proceeding to

step 10 and fastening the mirror. *

SECTION 3 - TOGGLE BOLT INSTALLATION

TOGGLE BOLT INSTALLATION

During Step 4 & 5, if toggle bolts are used, follow the steps bellow:

ﬁg. 11

ﬁg.9

ﬁg.10

i) Drill marked holes with an 11mm drill bit.

ﬁg.11

ii) Dismantle the toggle bolt. (See Fig. 9)

iii) Insert the threaded bolt through

the Hang ‘N’ Lock cams and reattach

the plugs and spring.

(See Fig. 10)

Note: Ensure the screws go

through the holes with the

counter-bore holes.

iv) Push the spring loaded wall braces

on the toggle bolts through the drilled

holes and loosely secure the Hang ‘N’

Lock bracket to the wall. (See Fig. 11)

1. 2.

*Continue from STEP 6 on the

main instruction leaﬂet*

COUNTERSINK

SCREWS

MIR 038 R06

SECTION 4 - CONNECTING THE ELECTRICAL SUPPLY

REMOVE THE MIRROR FROM THE WALL.

ENSURE THAT THE DOMESTIC ELECTRICAL MAINS SUPPLY TO WHICH THE

CABINET IS TO BE CONNECTED IS TURNED OFF.

Connect the ﬂexible mains supply cable on the mirror to the domestic electrical mains

supply ensuring that:

• The Live (Brown) conductor is connected to the Live on the domestic electrical mains

supply.

• The Neutral (Blue) conductor is connected to the Neutral on the domestic electrical

mains supply.

• The Earth (Green/Yellow) conductor is connected to the Earth/Ground on the domestic

electrical mains supply.

Note: Connection of the product to the domestic electrical mains supply must only be

carried out by a Building Regulations Part P certiﬁed electrician or must be checked by

your Local Authority Building Control Department.

Hang the mirror and secure the L bracket to the mirror using the bolt provided. (Step 10)

SECTION 5 - OPERATING THE MIRROR

FOLLOW THESE INSTRUCTIONS TO OPERATE THE MIRROR

FROM OFF:

1. Single SHORT TOUCH AND RELEASE to turn ON light and activate anti-fog function.

2. Single SHORT TOUCH AND RELEASE to turn OFF light and de-activate anti-fog

function.

Colour temperature: 6400K

SECTION 6 - DECLARATION OF CONFORMITY

THIS PRODUCT COMPLIES WITH THE REQUIREMENTS OF

The UK Electrical Equipment (Safety) Regulations 2016

The UK Electromagnetic Compatibility Regulations 2016

The UK Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment

Regulations 2012

The EU Low Voltage Directive (LVD) 2014/35/EU

The EU Electromagnetic Compatibility (EMC) Directive 2014/30/EU

The EU Restriction of Hazardous Substances (RoHS) Directive 2011/65/EU

The following UKCA and CE Declarations of Conformity can be requested from info@croydex.co.uk or

downloaded from www.croydex.com:

UKCA electrical safety and EMC (UKCA-DoC-00001-Safety-EMC.pdf)

UKCA RoHS (UKCA-DoC-00001-RoHS.pdf)

EU CE LVD and EMC (CE-DoC-00001-LVD-EMC.pdf)

EU CE RoHS (CE-DoC-00001-RoHS.pdf)

Tabla de contenidos

Otros manuales de Producto de cuidado personal de Croydex

Croydex

Croydex HANG 'N' LOCK MADISON WC147369E Manual de usuario

Croydex

Croydex Halington MM720500E Manual de usuario

Croydex

Croydex CHAUMONT MM8301 E Series Manual de usuario

Croydex

Croydex Danby Beauty Station White Manual de usuario

Croydex

Croydex Houston WC147169E Manual de usuario

Croydex

Croydex Carra WC450622 Manual de usuario

Croydex

Croydex FLEXI-FIX WC147669E Manual de usuario

Croydex

Croydex MEDWAY WC871405 Manual de usuario

Manuales populares de Producto de cuidado personal de otras marcas

Pretika

Pretika ST102 Manual de instrucciones

Beurer

Beurer FC 76 Manual de usuario

Pebble Grey

Pebble Grey 500.40.70-75 Manual de usuario

PUSH

PUSH ortho Manual de usuario

Dermlite

Dermlite DL3N Manual de usuario

DERMAPEN

DERMAPEN SEMI Manual de usuario

HiB

HiB Spectre 50 Manual de usuario

Carex

Carex SunLite Manual de usuario

Roper Rhodes

Roper Rhodes Intense Manual de lista de piezas

Interacoustics

Interacoustics Titan IMP440 Instrucciones de funcionamiento y seguridad

ReTrak

ReTrak VS001 Manual de usuario

LED Technologies

LED Technologies dpl PAIN RELIEF Joint Wrap Manual de usuario

Casa Lusso

Casa Lusso MVL1000x450PR Manual de usuario

Quoizel

Quoizel QR3326 Instrucciones de montaje

Beurer

Beurer EM 37 Manual de usuario

BERTSCHAT

BERTSCHAT HEATED HOODIE PRO - DUAL HEATING Manual de usuario

ACP

ACP OMNISTAND Manual de usuario

Scarlett

Scarlett VitaSpa SC-CA304PS11 Manual de usuario