Crowcon CellarSafe Manual de usuario

Issue 505/2006

Issue 5

The CellarSafe is designed for easy installation using mains power supply. It is pre-calibrated and

has been designed for one man installation. The alarm levels are factory set and the relays are ‘fail

safe’ so in event of power failure the alarms will activate.

Issue 5

Issue 5

Contact Crowcon

Contact Crowcon

Contact Crowcon

Contact Crowcon

Issue 5

CellarSafe is fitted with an AC plug for convenience, however if permanent installation is required, it

should be wired to a dedicated AC spur fed from a circuit breaker, marked as the disconnecting

device for the CellarSafe.

The circuit breaker must comply with the relevant requirements of IEC 947-1and IEC 947-3. These

procedures ensure that the installation complies with the requirements EN 61010-1 (Low Voltage

Directive).

The repeater unit supplied with CellarSafe does not need specialist cabling. Each additional

repeater unit is supplied with a 9m cable as standard.

Issue 5

3.0%

Issue 5

115v ac option available

Note: CO2 alarms are Subject to a 25 second time delay to prevent false alarms when exchanging

gas cylinders. Oxygen alarms are instantaneous.

6 CALIBRATION AND TESTING

6.1 Introduction

It is necessary to test this product at least every twelve months to ensure that the sensors and

alarms are operational. Periodic testing may be performed simply by using exhaled breath to

generate high CO2and low oxygen alarms on units with an oxygen sensor fitted. Exhaled breath

contains approximately 4% CO2and 16% oxygen, and therefore contains sufficient levels of each

gas to cause alarms on the CellarSafe monitor.

To test the alarms, blow into a plastic bag and hold the open end of the inflated bag tightly over

the sensor(s) until the alarms activate. The CellarSafe display will show increased levels of CO2

and decreased levels of oxygen (on units with an oxygen sensor fitted), and the alarms should

activate after approximately 10-15 seconds for oxygen and 25 seconds for CO2.

Alternatively, Crowcon can provide a calibration unit and calibration gas for checking and

calibrating the sensors. The following sections describe the calibration procedure.

Issue 5

6.2 Calibration

7

Issue 5

6.3

Issue 5

2 Adjust the gas flow to 750 ml/min for the carbon dioxide only monitoring system and

1.5 l/min for the dual gas monitoring system.

9

Tabla de contenidos

Otros manuales de Instrumento de medición de Crowcon

Crowcon

Crowcon Tetra 3 Manual de usuario

Crowcon

Crowcon Sprint Pro 1 Manual de usuario

Crowcon

Crowcon Gas-Pro Manual de usuario

Crowcon

Crowcon Clip Manual de usuario

Crowcon

Crowcon Tetra Manual de usuario

Crowcon

Crowcon Xgard ESU C01987 Manual

Crowcon

Crowcon Gasman Manual de usuario

Crowcon

Crowcon APM 155 Manual de usuario

Crowcon

Crowcon Triple Plus+ Manual de usuario

Crowcon

Crowcon APM 145 Manual de usuario

Crowcon

Crowcon Gas-Pro Manual de usuario

Crowcon

Crowcon SprintPro 3 Manual de usuario

Crowcon

Crowcon Gas-Pro Manual de usuario

Crowcon

Crowcon Gas-Tec Manual de usuario

Crowcon

Crowcon M07630 Manual de usuario

Crowcon

Crowcon APM 135 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario