Crono APO-go Instrucciones de funcionamiento

apomorphine hydrochloride

PUMP

APO-go PUMP

PROGRAMMING GUIDE

Locking/unlocking the APO-go PUMP

Switching between APo1 and APo3 modes

Setting bolus/priming dose and syringe volume

a. Bolus/priming conversion chart

Switching the APO-go PUMP on

Setting the ﬂow rate in APo1 mode

a. Dosage to ﬂow rate conversion table

Programming variable ﬂow rate in APo3 mode

Priming the line in APo1 mode

Priming the line in APo3 mode

Administering the bolus dose

Pausing the infusion

Retracting the plunger to the start position

Error codes

Contents

apomorphine hydrochloride

PUMP

Introduction

The following guide provides guidance to help you when programming the APO-go MARK III PUMP, including helpful

diagrams of what the screen should show at each step.

The APO-go MARK III PUMP has two available programming modes: APo1 and APo3. The APo1 mode is used for a single

ﬂow rate, whereas APo3 allows the programming of four different ﬂow rates, for variable ﬂow rate. The different

functionalities and a brief explanation of these is included below.

APo1 mode APo3 mode

Locking/unlocking feature Locking/unlocking feature

10ml or 20ml volume setting 10ml or 20ml volume setting

Bolus dose function Bolus dose function

Stop/start/pause infusions on demand Stop/start/pause infusions on demand

Single ﬂow rate Clock setting with variable ﬂow rate

Bolus dose lockout time

Functionality

Locking/unlocking

The APO-go PUMP can be locked and unlocked by a healthcare professional (HCP) or carer, preventing a patient from

changing their dose, against their prescriber’s advice. Whilst locked the patient can start/stop/pause an infusion whenever

they need to and also administer the set bolus dose.

Bolus dose function

The APO-go PUMP has a bolus dose function, which allows HCPs to programme a dose for patients to administer whenever

they require.

Variable flow rate

The variable flow rate function on the APO-go PUMP allows four separate flow rates to be programmed and assigned to each

hour of the day. One of the four flow rates is 0.00 for times when a break in infusion is required.

Bolus dose lockout time

Once the bolus dose has been set, the HCP may specify a time limit between bolus doses, locking the bolus dose feature

during this timeframe and avoiding multiple bolus doses being administered in short periods of time.

Pump set to OFF and unlocked (L0)

Press and hold until you hear a long beep - then release. The priming dose/bolus dose will flash with a dsymbol

Press or to decrease or increase the dose in ml

NOTE: Make any changes within 5 seconds otherwise the PUMP will return to the

OFF

state

Press again to move display to syringe volume - CC is displayed 1ml = 1cc

NOTE: This next setting is only modifiable if the piston is at the start of infusion position

Press or to decrease or increase the volume to 10 or 20 and leave for a few seconds for the change to be stored

If a change is made a beep will sound as the plunger extends to the desired position, P.cc flashes and the display counts to

the new position. There is no beep if the plunger retracts

A final beep will sound when the desired position is reached as the display returns to OFF

Solution used = 5mg/ml strength. The bolus/priming volume has a setting range of 0.02ml to 0.99ml, e.g. to give 3mg dose, 3 x 2/10 = 0.6, there-

fore you will require a setting of 0.61 ml, since the volume increases in increments which will not allow a setting of precisely 0.6ml.

Bolus/priming dose in mg Bolus/priming volume in ml (setting on PUMP)

0.5 0.11

1 0.22

2 0.41

3 0.61

4 0.81

5 0.99

Locking/unlocking

This task requires the pressing of two buttons simultaneously Display screen

L1 = locked. Padlock symbol on display

L0 = unlocked. No padlock

PUMP set to OFF or S oP

Press and hold until you hear a long beep and display shows PCXXXX -

Do not release button

Whilst still pressing immediately press too - display will flash either:

- ‘LO’ (unlocked) or

- ‘L1’ (locked)

Release the buttons and press or to switch between locked and unlocked

Press or leave the PUMP for a few seconds to confirm selection - display returns to OFF

Locking/unlocking the APO-go PUMP Setting the bolus/priming dose and syringe volume

Bolus/priming conversion chart to show typical settings

Pump set to OFF and unlocked (LO)

Press and hold until PC 0000 is displayed

Continue to hold the button down until the display shows SET

Press

once then use or to switch between

APo1 or APo3 modes

Press again to set the desired mode

NOTES: If there is an arrow visible in the bottom right-hand corner of the screen the PUMP is in APo1 mode

(this will be visible even when the PUMP is

OFF

)

APo1 MODE

Switching between APo1 and APo3 modes

P( 0000 SE

APo1 APo3

APo3 MODE

APo1 MODE APo3 MODE

Pump set to OFF

The ON/OFF button is the red button, press and hold until you hear a beep - then release

Display will scroll through the bolus/priming dose (and beep), flow rate (and beep), length of infusion in hours (and beep)

EITHER

If no further action taken - a final beep sounds as the infusion starts - the ‘drop’ icon will start flashing and the display

shows time of infusion remaining

See “Setting the flow rate” to programme the infusion flow rate

Pump set to ‘ON’ (Press ) and unlocked (L0)

With the display showing duration of infusion (hours and minutes), press and hold until you hear a long beep - then

release. Flow rate flashes with Fsymbol

Press or to decrease or increase the flow rate to the desired level

NOTE: Make any changes within 5 seconds otherwise the infusion will start

When desired rate is entered, wait 5 seconds - a beep will sound as the display returns to show revised time of infusion

remaining. The ‘drop’ icon will start flashing

Settings between 0.05ml/hr to 5.00ml/hr are available.

Values shown here are 0.4ml/hr to 2.0ml/hr. Solution used = 5mg/ml strength (i.e. APO-go Pre-filled syringe).

20ml syringe 20ml syringe with spacer

Flow rate value to set on PUMP 20ml setting (i.e. 100mg APO-go) 10ml setting (i.e. 50mg APO-go)

mg per hour ml per hour Hours/minutes running time Hours/minutes running time

2.0 0.40 25.00

2.5 0.50 20.00

3.0 0.60 16.41

3.5 0.70 14.17

4.0 0.80 24.59 12.30

4.5 0.90 22.13 11.07

5.0 1.00 20.00 10.00

5.5 1.10 18.10 9.05

6.0 1.20 16.40 8.20

6.5 1.30 15.22 7.41

7.0 1.40 14.17 7.09

7.5 1.50 13.20 6.40

8.0 1.60 12.30 6.15

8.5 1.70 11.46 5.53

9.0 1.80 11.07 5.34

9.5 1.90 10.31 5.16

10.0 2.00 10.00 5.00

Step 1: Entering set up mode

Ensure the PUMP says OFF, is unlocked and on the 20ml setting. 20 OFF

Press and hold (for up to 10 seconds) until the screen says SE .SE

Press until the screen shows APo1.APo1

Press until the screen shows APo3.

Leave the PUMP to revert to the original OFF position. APo3

Step 2: Setting the time

Press and hold until the screen displays the time.

To set the time, press and hold until the hours begin to flash. Adjust the hour by

pressing the and buttons.

Adjust the minutes by pressing the button until the minutes begin to flash,

use and to adjust appropriately.

When you have reached the correct time press .

Note: Ensure time is set to current time and ensure to change the time when the clocks go forward or back

13:27

Step 3: Setting the bolus dose

Once the correct time has been set on the PUMP, the screen will display the bolus dose.

Use the and buttons to adjust the prime dose to the desired dose.

When finished setting the bolus dose press .

Note: Refer to Bolus/priming conversion chart on Page 2

0.15

Step 4: Setting the bolus dose lockout time

Once the bolus dose has been set the screen will display no.L , this setting controls the bolus dose.

Pressing the locks the bolus dose for a set time.

For example, setting this figure to 5 minutes means that once bolus dose has been

pressed, there is a 5 minute delay before it can be pressed again.

Press to progress.

Note: If this setting is not required, leave it saying

no.L

Switching the APO-go PUMP on

Setting the ﬂow rate in APo1 mode

Dosage to flow rate conversion table

Programming variable ﬂow rate in APo3 mode

APo1 MODE

APo3 MODE

The screen will show F1 with a number next to it. This is your first flow rate.

Referring to your flow rate record set the flow rate for F1 using and buttons.

Press to progress.

0.60

The screen will show F2 with a number next to it. This is your second flow rate.

Referring to your flow rate record set the flow rate for F2 using and buttons.

Press to progress.

0.75

The screen will now show F3 with a number next to it. This is your third flow rate.

Referring to your flow rate record set the flow rate for F3 using and buttons.

Press to progress.

Note: If a third flow rate is not required skip to the next step

Refer to Dosage to flow rate conversion table on page 3

0.80

Step 6: Setting the flow rate per hour

The screen will now display , hF, 0.F (1, 2 or 3).

Use to control the hours and to select the flow rate.

Starting at 0(midnight), use to select the correct flow rate correlating to your flow rate record sheet.

Press to change the hour to 1am and use to select the flow rate.

Repeat until all flow rates are set (e.g. 2am, 3am, 4am...)

Press when all hours and flow rates have been set.

Note: If you go past the correct flow rate continue pressing

until it appears again

If you miss a time then keep pressing

until the time appears again

0.F1

1.F0

2.F2

Step 7: Altering the volume

The screen will say cc20, this is your ml setting.

Press and to adjust the pump to the 10ml setting (if required).

Press to progress.

The screen will display OFF and set up is complete. OFF

Step 5: Setting the flow rate

Pump set to ‘ON’

Press and hold until you hear a long beep - then release

Display will show the bolus dose being infused into the line, with dflashing. Beeps will sound at every 0.11ml with a long

beep when the full dose had been administered. Display shows revised time of infusion remaining

NOTES:

- This function can also be used to deliver a bolus dose

- The priming/bolus dose can be stopped by pressing the button

Priming the line in APo1 mode

Press and hold to turn the PUMP ON the screen will display Pr

Press and hold

until the liquid has reached the needle tip

Then press and hold , the PUMP will display On then show the remaining infusion time

Once the line is primed if the pump is left for a few seconds the

PUMP will switch to OFF with Pr flashing in the bottom right hand corner

Note: If this is the case, repeat steps 1 to 3

APo3 MODE

Priming the line in APo3 mode

APo1 MODE

Error functions for MARK III PUMP in APo1 mode only

Error Message Description Action

Err Unfeasible operation No action required

Er 2 Safety system error Press button

Er 3 Irregularity of motor circuit Press button

Er 4 Obstruction of plunger during retraction Remove obstruction. Restart PUMP by removing battery and reinserting after 15 seconds

Er 5 Irregularity of plunger mechanism Press button

Er 6 Motor irregularity Restart PUMP by removing battery and reinserting after 15 seconds

Er 7 Internal communication error Press button

Er 8 Reading memory error Restart PUMP by removing battery and reinserting after 15 seconds

Er 9 Motor circuit error Restart PUMP by removing battery and reinserting after 15 seconds

OCCL Occlusion of infusion line Clear occlusion and press button

Er,d Bolus dose set to 0.00ml Function not available

Error functions

Error functions for MARK I PUMP only

Error Message Description Action

Err Unfeasible operation No action required

Err 1 Occurs when battery is inserted, some

initial setting may be wrong Remove and reinsert battery after 15 seconds

Err 2 The motor has stopped in order to avoid

overrunning Press button to restart

Err 3 Irregularity of motor circuit Press button to restart

Err 4 Obstruction of plunger during END

phase of retraction Remove the obstruction. Restart PUMP by removing battery and reinserting after 15 seconds

Err 5 Irregularity of plunger during retraction.

Plunger may be damaged Press button. Alternatively, remove battery and re-insert after 15 seconds

Err 7 Mechanical/motor block during backwards

movement Restart PUMP by removing battery and reinserting after 15 seconds

Err 8 Reading memory error Restart PUMP by removing battery and reinserting after 15 seconds

Err 9 Motor circuit error Restart PUMP by removing battery and reinserting after 15 seconds

Err 11 Flow rate is above maximum setting Restart PUMP by removing battery and reinserting after 15 seconds

OCCL Occlusion of infusion line Clear occlusion and press button

7 8

Administering the bolus dose

While the pump is on, press and hold until you hear a long beep - then release

The screen will show the bolus dose being infused with dflashing. Beeps will sound at every 0.11ml with a long beep when

the full dose has been administered. If required, the bolus dose can be stopped pressing the button

Note: If a lock out time has been set (APo3 mode only) this will limit the time between bolus doses

Refer to Setting the bolus dose lockout time on page 4 for more details

PAUSING THE INFUSION While the infusion is running press and hold ,

the display will now show S oP

The PUMP can be restarted by pressing and holding

Pausing the infusion

Retracting the plunger to the start position

NOTE: The infusion line must always be DISCONNECTED from the patient before the plunger is retracted

The syringe should not be removed until the plunger is fully retracted

RETRACTING IF THE INFUSION HAS NOT ENDED:

Stop by pressing and holding - display shows S oP, press to stop beeping

Disconnect the infusion line

End infusion by pressing and together - a long beep will sound and display will show End

then I---- as the plunger withdraws.

A beep will sound when completed and the display returns to OFF

RETRACTING AT THE END OF THE INFUSION:

NB - An intermittent beep will sound at 10 minutes and at 5 minutes before the end of infusion.

At the end of infusion an on-going beep will sound and the display will show

End

PUMP display shows End

Disconnect infusion line

Press and hold to stop beeping and retract plunger - display will show I----

Plunger retracts and beeps when it has reached the start position - display shows OFF

APo1 MODE APo3 MODE

Date of preparation: December 2017

AP01-1117-9084

Britannia Pharmaceuticals Limited,

200 Longwater Avenue, Green Park, Reading, RG2 6GP

apomorphine hydrochloride

Adverse events should be reported. Reporting forms and information can be found at www.mhra.gov.uk/yellowcard

Adverse events should also be reported to Medical Information on 0870 851 0207 or [email protected]

APO-go Technical Helpline 0844 880 1327

24 hours a day, 365 days a year

Part of the Package of Care provided by Britannia Pharmaceuticals

Tabla de contenidos

Manuales populares de Equipo médico de otras marcas

TekTone

TekTone Tek-CARE160 Manual de usuario

NeuroMetrix

NeuroMetrix Quell 2.0 Manual de usuario

AMT

AMT XLR8 Manual de usuario

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 Manual de usuario

EDAN

EDAN SONOTRAX Pro Manual de usuario

Restorative Therapies

Restorative Therapies RT300 Manual de usuario

Gendex

Gendex Expert DC Manual de usuario

Dexcowin

Dexcowin ADX4000W Manual de usuario

Libelium

Libelium MySignals Manual de usuario

Acelity

Acelity V.A.C.ULTA 4 Manual de usuario

Caputron

Caputron ActivaDose II tDCS Manual de usuario

FujiFilm

FujiFilm Sonart Manual del propietario

Plinth 2000

Plinth 2000 93CDT Manual de usuario

GE SENOGRAPHE 800T Manual de usuario

GE Definium 5000 Manual de usuario

Kanmed

Kanmed GE-1380 Manual de usuario

Huntleigh

Huntleigh FD1 Manual de usuario

Stryker

Stryker SPR Plus Manual de usuario