Crestron ST-4T Manual de usuario
CRESTRON
Operations Guide - DOC. 5703 Contents •• i
Contents
Hand-Held Wireless Transmitter 1
Description ..........................................................................................................................1
Functional Description ...........................................................................................1
Physical Description...............................................................................................1
Leading Specifications.........................................................................................................3
Setup....................................................................................................................................4
Identity Code..........................................................................................................4
Programming .........................................................................................................5
Problem Solving...................................................................................................................9
Troubleshooting .....................................................................................................9
Further Inquiries .................................................................................................. 10
CRESTRON
Operations Guide - DOC. 5703 Hand-Held Wireless Transmitter •• 1
Hand-Held Wireless Transmitter
Description
Functional Description
The ST-4T and ST-8T are hand-held radio-frequency (RF) transmitters. The units
are designed to operate with the SmarTouch STS via the ST-CP, control processor.
The hand-held transmitter is available with four (ST-4T) or eight (ST-8T) button
controls. Depression of any fixed button on the button panel initiates a RF signal
transmission to the ST-CP.
Both hand-held transmitters have a power-saving mode, known as sleep mode, to
extend battery life. Units are continually in sleep mode until a button is depressed.
The unit activates immediately. It is not necessary to hold down a button.
Physical Description
ST-4T and ST-8T electronic hardware is housed in a slim, high-impact molded
ABS black plastic enclosure,as shown on the next page. A button array on the
printed circuit board is covered by a button panel. All button panels include custom
engraving with large light gray button caps and black finish. Refer to the latest
version of the CRESNET II Engraving Worksheet for the ST-4T and ST-8T (Doc.
5704 and 5705, respectively) for engraving directions.
A red Transmit LED is located above the button panel cover. The Transmit LED
indicates RF transmission and illuminates when a button is depressed. It also has
the auxilliary function of illuminating when a new transmitter RF ID code is
programmed into the unit.
CRESTRON
2•• Hand-Held Wireless Transmitter Operations Guide - DOC. 5703
ST-4T Physical Views
SIDE VIEW FRONT VIEW
ST-8T Physical Views
FRONT VIEWSIDE VIEW
CRESTRON
Operations Guide - DOC. 5703 Hand-Held Wireless Transmitter •• 3
A standard nine-volt battery is included with all units. Access to the battery is
permitted after the battery cover, located on the underside of the unit, is removed. A
sensor (photo transistor) used to program an identity code is also located in the
battery compartment, as shown below.
Battery Compartment (Rear View)
Leading Specifications
The table below provides a summary of leading specifications for the hand-held
transmitters. Dimensions and weight are approximations rounded to the nearest
thousandth unit.
Leading Specifications of the ST-4T and ST-8T
SPECIFICATION DETAILS
Battery 9V DC
CRESNET II Workshop Version 5.0 or later
CRESNET II Operating System SR30222.OPS or later
SmarTouch Operating System Any
STS VisionTools for Windows Version 10.4 or later
Compiler 3.09.17 or later
Dimensions & Weight
Height: 6.500 in (16.510 cm)
Width: 2.750 in (6.985 cm)
Depth: 0.800 in (2.032 cm)
Weight: 0.300 lb (0.200 kg)
CRESTRON
4•• Hand-Held Wireless Transmitter Operations Guide - DOC. 5703
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. The equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
n Reorient or relocate the receiving antenna.
n Increase the separation between the equipment and receiver.
n Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
n Consult the dealer or an experienced radio/TV technician for help.
As of the date of manufacture, the unit has been tested and found to comply with
specifications for CE marking.
Setup
Identity Code
Every hand-held wireless transmitter communicating with either the ST-CP
requires a unique RF identity code (ID CODE). There are 254 possible two-digit
hexadecimal alphanumeric codes ranging from 01 to FE. To maintain code diversity
within SmarTouch STS, use codes between 10 and FE for the transmitters.
NOTES: The RF ID CODE on the hand-held transmitters is factory set to 11.
Do not use 00 or FF as an RF ID.
Do not confuse RF ID with network (NET) ID.
Use STS VisionTools for Windows to set an RF ID CODE. Select ViewPort from
the Tools menu; the “Crestron Performance Viewport” dialog box appears.
CRESTRON
Operations Guide - DOC. 5703 Hand-Held Wireless Transmitter •• 5
Crestron Performance Viewport Dialog Box
From the Options menu in the dialog box, select Set Transmitter ID to open the “Set
Transmitter ID” dialog box. Enter a two-digit hexadecimal number ranging from 03
to FE. Click OK to confirm.
Set Transmitter ID Dialog Box
Programming
STS VisionTools for Windows contains sample projects, ST4T.prj and ST8T.prj,
that can be used when programming the hand-held wireless transmitters. Simply
copy the respective sample project by selecting Copy Project from the File menu of
an open project. The “Copy Project” dialog box is displayed.
CRESTRON
6•• Hand-Held Wireless Transmitter Operations Guide - DOC. 5703
Copy Project Dialog Box
NOTE: The illustration above shows what the “Copy Project” dialog box would
look like if the programmer were to copy the ST-4T sample project with the new
project name, remote-1.
As illustrated, a "From" and "To" field is provided. If the desired project is not
present in the field, directly key in the path name (at the From: box) or select
Browse to display the "Open" dialog box and scroll through directories to establish
the correct path of a desired source for the copy. The destination path is entered in
the same manner. Once source and destination paths have been chosen, select Copy
to initiate project copying. By default, all copied graphic files are copied to the same
directory as the project or touchpanel.
The sample projects for the hand-held transmitters have one page each. The ST-4T
page and ST-8T page have four and eight momentary-type buttons, respectively.
Each large button has two join numbers associated with it, one for each half of the
button. Commands such as VOLUME UP and VOLUME DOWN are usually
assigned to the separate button halves; operation of each half is achieved by
pressing down on that side of the button. Refer to the following illustration of the
sample ST-4T page. Notice the join number assignments for each button.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Transmisor de Crestron
Crestron
Crestron DM-TX-200-C-2G Manual de usuario
Crestron
Crestron CNIRHT-MM Manual técnico
Crestron
Crestron DM-TX-4KZ-202-C Manual de usuario
Crestron
Crestron IM-WCVP Guía de inicio rápido
Crestron
Crestron HD-TXA-4KZ-101 Manual de usuario
Crestron
Crestron 4K DigitalMedia 8G+ DM-RX-4K-202-C Manual del propietario
Crestron
Crestron DM-TX-4K-202-C Dibujo dimensional
Crestron
Crestron HD-TXCA-4KZ-101 Manual de usuario
Crestron
Crestron HD-TXA-4KZ-101-1G Manual de usuario
Crestron
Crestron DM-TX-4KZ-202-C Dibujo dimensional
Crestron
Crestron DM-TX-4K-202-C Manual del propietario
Crestron
Crestron CNLCDRFHT-A Manual de usuario
Crestron
Crestron DigitalMedia HD-TX-4KZ-421-CHGR Manual de usuario
Crestron
Crestron DigitalMedia DM-TX-100F Manual de usuario
Crestron
Crestron DM-TX-200 Cómo utilizar
Crestron
Crestron QM-TX Manual de usuario
Crestron
Crestron DM-TX1-4K-C-1G Manual de usuario
Crestron
Crestron DigitalMedia DMF-TX-4K-SFP Dibujo dimensional
Crestron
Crestron HD-TXC-4KZ-101 Manual de usuario
Crestron
Crestron IM-TCC Cómo utilizar
Manuales populares de Transmisor de otras marcas
Dejero
Dejero EnGo 3x Manual de usuario
Rosemount
Rosemount 4600 Manual de usuario
Speaka Professional
Speaka Professional 2342740 Manual de usuario
trubomat
trubomat GAB 1000 Manual de usuario
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manual de usuario
Rondish
Rondish UT-11 Manual de usuario
