Crestron FlipTop FT2 Series Manual de usuario

The Crestron® FT2-700-ELEC-PTL FlipTop™ cable management system

installs into a table or other horizontal surface to provide modular

connectivity. It features a retracting lid that disappears within the

enclosure. When the lid is retracted, 12 module slots are arranged in two

rows of six. The flexible modular design may also be customized with an

assortment of Crestron accessories, and the pass-through lid style

allows cables to be fully extended while the lid is closed.

For more information about the accessories, please visit

www.crestron.com/Crestron-FlipTops. To configure your FlipTop, launch

the FlipTop Configuration Tool.

In the Box

1FT2-700-ELEC-PTL

Additional Items

3 Locking Bars with screws and gaskets (4532479)

1 Cable, DC Power Splitter (2050094)

1 Connector, Plug (2003575)

1 Holder, Power Supply (2048887)

1 Power Cord, 5 ft 10 in. (1.78 m) (2042043)

1 Power Pack, 24VDC, 2.5 A, 100-240VAC (2045873)

1Cutout Template (4527491)

FT2-700-ELEC-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Electrical, Pass-Through Lid

Mount the FlipTop Assembly

A mounting hole is required for an FT2-700-ELEC-PTL installation. Use

the included template to cut a mounting hole for new installations. The

FT2-700-ELEC-PTL may also replace an FT-600 FlipTop or Extron®

Cable Cubby® 700 Cable Access Enclosure using the existing mounting

hole.

When determining the location for the FT2 assembly, consider where

users will be seated and their proximity to the FT2 assembly's modules

and retractors. Refer to the FT2A-CBLR-1T and FT2A-CBLR-GR series

cable retractors for above-the-table cable pull-out lengths.

For a new mounting, follow sections Cut the Mounting Hole and Secure

the FlipTop Assembly. To use the mounting hole of an existing FT-600

FlipTop assembly, follow sections Replace the FT-600 FlipTop Assembly

and Secure the FlipTop Assembly.

Cut the Mounting Hole

A saw and the included cutout template are required to cut the

mounting hole.

1. Check the table surface and the area beneath the table. Clear any

obstructions that may impede the installation or functionality of the

FT2 assembly, retractors, and accessories.

2. Using the included cutout template, trace an outline of the mounting

hole onto the table.

3. Cut the mounting hole in the table with an appropriate saw.

Replace the FT-600 FlipTop Assembly

The FT-600 FlipTop assembly mounting hole is larger than the mounting

hole required for the FT2 assembly. FT2A-SPCR-MNT-10 plastic spacers

(sold separately) are used to help fill the gap between the mounting hole

and the FT2 assembly.

1. Loosen the four socket screws that secure the two mounting plates

and the FT-600 FlipTop assembly to the surface.

2. Remove the FT-600 FlipTop assembly.

3. Attach the four plastic spacers to each corner of the

FT2-700-ELEC-PTL.

4. Continue to prepare the FT2-700-ELEC-PTL by attaching the DC

power splitter cable. Refer to Secure the FlipTop Assembly.

FT2-700-ELEC-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Electrical, Pass-Through Lid

Secure the FlipTop Assembly

To prepare the FT2-700-ELEC-PTL and secure it to the table surface:

1. Gently remove the bezel before securing the FT2 assembly to the

table. It is held in place with magnets.

2. Locate the included DC power splitter cable.

3. On the underside of the FT2 assembly, locate the power bus and

connect the dual-connector ends of the DC power splitter cable to

the two barrel jacks of the power bus. The cable will be accessed later

in Connect the FlipTop Assembly.

4. Ensure that all four swiveling dogs are tucked inside of the FT2

assembly, and then insert the FT2 assembly into the mounting hole

until the top lip is flush with the table surface.

FT2-700-ELEC-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Electrical, Pass-Through Lid

5. Carefully tighten the four swiveling dogs in each corner of the FlipTop

assembly clockwise until the FT2 assembly is secured in place against

the table. Do not overtighten the swiveling dogs.

CAUTION: A screwdriver or manual torque screwdriver at its lowest

setting may be used to tighten the swiveling dogs. Avoid stripping

the swiveling dogs and damaging the table.

If removing the FT2-700-ELEC-PTL from the table, ensure that the

screwdriver rotation is set correctly before loosening the swiveling

dogs.

Connect the FlipTop Assembly

Access the two network connectors and two power bus barrel jacks on

the underside of the FT2 assembly.

FT2-700-ELEC-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Electrical, Pass-Through Lid

Connect the Network

Automate the one-touch retractors by connecting all retractors in an

FT2 assembly to a control system and a switch, or to a DMPS via a single

Cresnet® cable. Custom programming can trigger the retractors after

five minutes of no video detected.

Connect the FT2 assembly to a Crestron control system or DMPS3 via

the 3-pin connector using standard Cresnet cable. The red power lead is

not connected and should be terminated.

Connect and Place the Power Supply

The FT2-700-ELEC-PTL ships with one 24VDC power supply that is used

to supply power to the power bus in the FT2 assembly. There are six

possible locations to attach the power supply. Connect the power supply

prior to installing any modules.

NOTE: Two power supplies are required if installing two rapid charging

modules in the FT2-700-ELEC-PTL. For more information, refer to the

FT2A-CHGR-USBA-BASICQuick Start Guide (Doc.8423) or

FT2A-CHGR-USBA/CInstallation Guide (Doc.8219).

To connect the power supply to the power bus:

1. Underneath the FT2-700-ELEC-PTL, connect the power supply to the

bottom of the power bus.

lIf connecting one power supply, connect the power supply’s power

cord to the single connector end of the DC power splitter cable.

Refer to step 1 in Secure the FlipTop Assembly.

lIf connecting two power supplies, connect each power supply’s

power cord to a barrel jack in the power bus.

2. Use the two included tie wraps to dress the power cord.

3. Slide the power supply into the power supply holder until it is secured

in place.

FT2-700-ELEC-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Electrical, Pass-Through Lid

4. Align the four keyed tabs on the power supply holder with four keyed

slots on the FT2 assembly. Then, push the power supply holder up and

into the slots so that the keyed tabs engage the wide end of the slots.

5. Slide the holder downward until it is secured to the FT2 assembly.

6. Connect the included 5ft 10in. (1.78m) power cord to the power jack

on top of the power supply.

7. Connect the other end of the power supply to a power source only

after all other modules have been installed and all connections have

been made to the FlipTop assembly.

FT2-700-ELEC-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Electrical, Pass-Through Lid

Install the Modules

All modules are sold separately and not included with the

FT2-700-ELEC-PTL FlipTop assembly. Installation procedures for most

modules are available in separate product documentation. For more

information, refer to the specific product manual located at

www.crestron.com/manuals.

The following sections provide best practices and installation procedures

for pass-through cable modules and blank plate modules.

Module Best Practices

Follow the best practices below when performing module installation.

lPerform module installation in the following order:

1. AC Power Outlet Modules (FT2A-PWR-US,FT2A-PWR-EU,

FT2A-PWR-AU,FT2A-PWR-FR,FT2A-PWR-IS,FT2A-PWR-IT,

FT2A-PWR-SW,FT2A-PWR-UK, and FT2A-PWR-UN)

2. Retractor modules (FT2A-CBLR-1T series and FT2A-CBLR-GR

series)

3. All other modules (FT2A-CP series, FT2A-CHGR series,

FT2A-PLT-PT, and FT2A-PLT-BLANK)

lPlace the FT2A-CBLR-GR modules only at the ends of a module row.

lDress all cables after installing each module.

Pass-Through Cable Module

The FT2A-PLT-PT pass-through modules (sold separately) enable

FT2-CBL-PT pass-through cables (sold separately) and other types of

interface cables to be installed within the FT2-700-ELEC-PTL. Each

FT2A-PLT-PT cable module is packaged with a nylon grommet and a

cable plate. An empty module slot in the FT2-700-ELEC-PTL and an

FT2-CBL-PT series or other interface cable are required for installation.

Installing the Pass-Through Cable Module with 4K Cables

The included grommet is not needed when installing most 4K cables. If

the cable is 10 mm or thinner, the grommet may be used.

1. Push the connector end of the cable through the hole in the cable

plate.

2. Insert the cable plate into one of the three slots in the pass-through

module. Choose the appropriate slot based on the length of the cable

connector. The top of the connector must sit flush with the top of the

module.

NOTES:

lIf the connector extends past the top of the pass-through

module, the lid cannot close.

lEnsure that the cable moves freely in the module prior to

attaching the side plate. The plate is difficult to remove once it is

attached.

FT2-700-ELEC-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Electrical, Pass-Through Lid

3. Attach the side plate to the module by snapping the plastic clips on

the plate into the two slots on the module.

NOTE: When removing the side plate, use a flat-head screwdriver to

carefully pry the plastic clips off of the module near the two slots.

4. Feed the other end of the cable through an empty module slot in the

FT2 assembly.

5. Slide the pass-through cable module into the same module slot as

mentioned in the previous step. Use the guide ribs on the front and

rear of each module to help position the module in the FT2 assembly.

Installing the Pass-Through Cable Module with Non-4K

Cables

The grommet is recommended to use with cables that are 10 mm or

thinner.

1. Open the grommet.

2. Insert a cable into the grommet with the connector facing up toward

the user.

3. Press the grommet back together to secure the cable inside.

4. Push the grommet and cable through the hole in the cable plate.

5. Insert the cable plate into one of the three slots in the pass-through

module. Choose the appropriate slot based on the length of the cable

connector. The top of the connector must sit flush with the top of the

module.

NOTES:

lIf the connector extends past the top of the pass-through

module, the lid cannot close.

lEnsure that the cable moves freely in the module prior to

attaching the side plate. The plate is difficult to remove once it is

attached.

FT2-700-ELEC-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Electrical, Pass-Through Lid

6. Attach the side plate to the module by snapping the plastic clips on

the plate into the two slots on the module.

NOTE: When removing the side plate, use a flat-head screwdriver to

carefully pry the plastic clips off of the module near the two slots.

7. Feed the other end of the cable through an empty module slot in the

FT2 assembly.

8. Slide the pass-through cable module into the same module slot as

mentioned in the previous step. Use the guide ribs on the front and

rear of each module to help position the module in the FT2 assembly.

Install the Blank and Keystone Plate Module

Blank plate modules (sold separately) fill empty slots in module rows,

and keystone plate modules (sold separately) allow for cables

terminated with standard keystone jacks to be installed in the FT2

assembly. The blank and keystone modules each require one empty

module slot for installation.

To install a blank or keystone plate module into the FT2-700-ELEC-PTL:

lSlide the blank plate module down into the appropriate module slot.

Use the guide ribs on the front and rear of each module to help

position it in the FT2 assembly.

lFor the keystone plate module, complete the following steps.

1. Snap the cable’s keystone jack into the keystone opening in the

keystone plate module.

2. Feed the cable down through the empty module slot.

3. Slide the attached keystone plate module down into the same

module slot using the front and rear guide ribs to assist with

positioning.

FT2-700-ELEC-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Electrical, Pass-Through Lid

Install the Locking Bars

To install the locking bars:

1. Position the locking bars so that the gasket and screws attached to

the locking bars engage the screw holes in the FT2 assembly.

2. Use a screwdriver to secure the locking bar screws to the FT2

assembly.

CAUTION: Do not overtighten the locking bar screws.

Install the Bezel

Place the bezel onto the FT2 assembly so that the retractable lid fits

inside the bezel opening. The bezel is held in place using magnets.

FT2-700-ELEC-PTL QuickStart

FlipTop™ FT2 Series Cable Management System, 700 Size, Electrical, Pass-Through Lid

Otros manuales para FlipTop FT2 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cables y conectores de Crestron

Crestron

Crestron Four-Way Amplified Splitter SRD-SPL-4 Manual de usuario

Crestron

Crestron SP-CBL Manual de instrucciones

Crestron

Crestron DM-8G-CONN-100 Manual de usuario

Crestron

Crestron FT2A-CP-USBA Manual de usuario

Crestron

Crestron SR9600 Guía de configuración

Crestron

Crestron SmartPresenter SPC-124 Manual de usuario

Crestron

Crestron CBL-MULTI-HD-6 Manual de usuario

Crestron

Crestron DigitalMedia Connectors DM-CONN-20 Manual del propietario

Crestron

Crestron TPSBLOCK-10 Manual de usuario

Crestron

Crestron QM-FTCMK Manual de usuario

Crestron

Crestron FlipTop CBLR2 Series Manual de usuario

Crestron

Crestron TPS-CBL-T Manual de usuario

Crestron

Crestron TPMC-CBL-T Manual de usuario

Crestron

Crestron ST-SPL Manual de usuario

Crestron

Crestron FT2-700-ELEC Series Manual de usuario

Crestron

Crestron FlipTop CBLR2 Series Dibujo dimensional

Crestron

Crestron UC-B-ACCY Manual de usuario

Crestron

Crestron TPS-CBL Manual de usuario

Crestron

Crestron SmartPresenter SPC-122 Manual de usuario

Crestron

Crestron ST-CBL Instrucciones de funcionamiento e instalación

Crestron

Crestron SmartPresenter SPC-550 Manual de usuario

Crestron

Crestron C2N-TXM-C50 Manual de usuario

Crestron

Crestron FlipTop FT2A-CBLR-1T Series Manual de usuario

Crestron

Crestron FT-PWR Cómo utilizar

Manuales populares de Cables y conectores de otras marcas

Philips

Philips SWA6310 Manual de usuario

StarTech.com

StarTech.com CRJ4550PK Manual de usuario

Nohau

Nohau EMUL-IP2K-PC Manual de usuario

Foxun

Foxun SX-SP144E-HD4K2K Manual de usuario

Philips

Philips SWA3305W Manual de usuario

opticis

opticis Stretch DVIM1-1P0x Manual de usuario

Volkswagen

Volkswagen VAS 6558A Manual de usuario

NEXIBO

NEXIBO N-13 Manual de usuario

CYP

CYP PU-1H3HBTL Manual de usuario

Allen-Bradley

Allen-Bradley 1784-u2dhp Manual de usuario

Global Caché

Global Caché Flex Link Blaster Manual de usuario

Hauppauge

Hauppauge USB-Live2 Manual de usuario

Fenix

Fenix MPSV 15 Manual de usuario

BEGA

BEGA 71 085 Manual de usuario

Tesla

Tesla HPWC Manual de usuario

GAMERON

GAMERON LUXURY TV CABLE Manual de usuario

molex

molex Milli-Grid Dual row 87568 Series Manual de usuario

Burndy

Burndy Continental Industries thermOweld CRE-7 Manual de usuario