Crestron HD-DA-2-QUAD Manual de usuario
The Crestron® HD-DA-2-QUAD is a single rack space unit containing four
independent 1-to-2 HDMI® distribution amplifiers. It is designed for
splitting up to four HDMI, DVI, or DisplayPort™ Multimode signals to feed
separate displays or processors, and is ideal for adding “loop-through”
capability to the inputs of a Crestron DVPHD Digital Video Processor. The
HD-DA-2-QUAD supports HDMI with Deep Color and HDCP, handling
1080p60 HDTV and WUXGA computer resolutions, and multichannel HD
lossless audio.
In the Box
1 HD-DA-2-QUAD, Quad 1-to-2 HDMI Distribution Amplifier
Additional Items
2 Bracket, Rack Ear, 1U (2004208)
1 Connector, 2-Pin (2003574)
4 Foot, 0.5 in. x 0.5 in. x 0.23 in., Adhesive (2002389)
1 Cable, Power, 5 ft 10 in. (1.8 m) (2042043)
1 Power Pack, 24 VDC, 2.5 A, 100-240 VAC (2045873)
Install the Device
The HD-DA-2-QUAD can be mounted into a rack or placed on a flat
surface.
Mount into a Rack
The HD-DA-2-QUAD occupies 1U of rack space. Use the three screws
from the front part of each side panel, and a #1 or #2 Phillips screwdriver
to attach the two included rack ears to the device, as shown in the
following illustration. Then mount the device into the rack using four
mounting screws (not included).
Rack Mounting Safety Precautions
Elevated Operating Ambient Temperature: If installed in a closed or
multi-unit rack assembly, the operating ambient temperature of the rack
environment may be greater than room ambient temperature. Therefore,
consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma)
specified by the manufacturer.
Reduced Airflow: Installation of the equipment in a rack should be such
that the amount of airflow required for safe operation of the equipment
is not compromised.
1
HD-DA-2-QUAD QuickStart
Quad 1-to-2 HDMI® Distribution Amplifier
Mechanical Loading: Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Circuit Overloading: Consideration should be given to the connection of
the equipment to the supply circuit and the effect that overloading of the
circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be
used when addressing this concern.
Reliable Earthing: Reliable earthing of rack-mounted equipment should be
maintained. Particular attention should be given to supply connections
other than direct connections to the branch circuit (e.g., use of power
strips).
Place on a Flat Surface
Attach the included feet near the corners on the underside of the
HD-DA-2-QUAD before placing it onto a flat surface or stacking it with
other equipment.
2
HD-DA-2-QUAD QuickStart
Quad 1-to-2 HDMI® Distribution Amplifier
Connect the Device
Connect the HD-DA-2-QUAD as called out in the following illustration.
Connect power last.
* The device may be powered by the included 24 VDC power pack or Cresnet network
power, but not both.
3
HD-DA-2-QUAD QuickStart
Quad 1-to-2 HDMI® Distribution Amplifier
Visit the Product Page
Scan the QR code to visit the product page.
HD-DA-2-QUAD
www.crestron.com/model/6502439
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. HDMI and the
HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in
the United States and/or other countries. DisplayPort is either a trademark or
registered trademark of Video Electronics Standards Association in the United States
and/or other countries. Other trademarks, registered trademarks, and trade names
may be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the marks and
names of others. Crestron is not responsible for errors in typography or photography.
©2020 Crestron Electronics, Inc.
Doc. 6713C
05/08/20
4
HD-DA-2-QUAD QuickStart
Quad 1-to-2 HDMI® Distribution Amplifier
Otros manuales para HD-DA-2-QUAD
1
Otros manuales de Amplificador de Crestron
Crestron
Crestron C2-AUDIO-6PAK Manual de usuario
Crestron
Crestron C2N-IADS30X24 Manual de usuario
Crestron
Crestron High-Gain Line Amplifier SRD-AMP-1 Manual de usuario
Crestron
Crestron HD-DA-2 Manual de usuario
Crestron
Crestron DM-NAX-8ZSA Manual de usuario
Crestron
Crestron AMP-2800 Manual de usuario
Crestron
Crestron Avia AMPI-8075 Dibujo dimensional
Crestron
Crestron Adagio AADS Manual de usuario
Crestron
Crestron MP-AMP40-70/100V Cómo utilizar
Crestron
Crestron X Series Manual de usuario
Crestron
Crestron DigitalMedia DM-MD6X4 Instrucciones de funcionamiento y mantenimiento
Crestron
Crestron PROAMP(I)-7X250 Manual de usuario
Crestron
Crestron HD-DA-2 Dibujo dimensional
Crestron
Crestron AMP-2210S Cómo utilizar
Crestron
Crestron AMP-8075 Manual de usuario
Crestron
Crestron on wall speaker Manual de usuario
Crestron
Crestron AMP-150-70 Dibujo dimensional
Crestron
Crestron DM NAX DM-NAX-4ZSP Manual de usuario
Crestron
Crestron CNAMPX-12X60 Manual de usuario
Crestron
Crestron HD-DA-4KZ-E Series Dibujo dimensional
