Craftsman 82003 Manual de usuario

Owner's Manual

True RMS

Multimeter

Model No.

82003

www.craftsman.com 042508

Safety

Operation

Maintenance

Español

CAUTION: Read, understand and

follow Safety Rules and Operating

Instructions in this manual before

using this product.

TABLE OF CONTENTS

Warranty Page 3

Safety Instructions 4

Safety Symbols 5

Control and Jacks 6

Symbols and Annunciators 6

Specifications 7

Battery Installation 11

Operating Instructions 12

DC Voltage Measurements 12

AC Voltage Measurements 13

DC Current Measurements 14

AC Current Measurements 15

Resistance Measurements 16

Continuity Check 17

Diode Test 17

Capacitance Measurements 18

Frequency (Duty Cycle) Measurements 18

Temperature Measurements 19

Autoranging/Manual range selection 20

Relative Mode 20

Display Backlight 21

Hold 21

Auto Power Off 21

Low Battery Indication 21

Maintenance 22

Battery Replacement 23

Fuse Replacement 24

Troubleshooting 25

Service and Parts 25

ONE YEAR FULL WARRANTY

CRAFTSMAN PROFESSIONAL ONE YEAR FULL

WARRANTY. If this product fails due to a defect in materials or

workmanship within one year from the date of purchase,

RETURN IT TO ANY SEARS STORE OR OTHER

CRAFTSMAN OUTLET IN THE UNITED STATES for free

replacement. This warranty gives you specific legal rights, and

you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

For Customer Assistance Call 9am - 5pm (ET)

Monday through Friday 1-888-326-1006

WARNING: USE EXTREME CAUTION IN THE USE OF THIS

DEVICE. Improper use of this device can result in injury or

death. Follow all safeguards suggested in this manual in addition

to the normal safety precautions used in working with electrical

circuits. DO NOT service this device if you are not qualified to do

so.

SAFETY INSTRUCTIONS

This meter has been designed for safe use, but must be operated

with caution. The rules listed below must be carefully followed for

safe operation.

1. NEVER apply voltage or current to the meter that exceeds the

specified maximum:

Input Limits

Function Maximum Input

V DC or V AC 1000VDC/AC rms

mA AC/DC 400mA AC/DC

A AC/DC 10A AC/DC (20A for 30 seconds

max every 15 minutes)

Resistance, Diode Test,

Continuity, Capacitance,

Frequency, Temperature

1000VDC/AC rms

2. USE EXTREME CAUTION when working with high voltages

3. DO NOT measure voltage if the voltage on the "COM" input

jack exceeds 1000V above earth ground

4. DO NOT measure current of circuits whose voltage is greater

than 600V above earth ground

5. NEVER connect the meter leads across a voltage source

while the function switch is in the resistance or diode mode.

Doing so can damage the meter

6. ALWAYS turn off the power and disconnect the test leads

before opening the cover to replace the fuse or battery

7. NEVER operate the meter unless the back cover is in place

and fastened securely

SAFETY SYMBOLS

This symbol adjacent to another symbol,

terminal or operating device indicates that the

operator must refer to an explanation in the

Operating Instructions to avoid personal injury

or damage to the meter.

This WARNING symbol indicates a potentially

hazardous situation, which if not avoided,

could result in death or serious injury.

This CAUTION symbol indicates a potentially

hazardous situation, which if not avoided, may

result damage to the product.

This symbol advises the user that the

terminal(s) so marked must not be connected

to a circuit point at which the voltage with

respect to earth ground exceeds (in this case)

1000 VAC or VDC.

This symbol adjacent to one or more terminals

identifies them as being associated with

ranges that may, in normal use, be subjected

to particularly hazardous voltages. For

maximum safety, the meter and its test leads

should not be handled when these terminals

are energized.

This symbol indicates that a device is

protected throughout by double insulation or

reinforced insulation.

WARNING

CAUTION

MAX

1000V

CONTROLS AND JACKS

1. 4,000 count LCD display

2. RANGE button

3. Hz and % button

4. Mode button

5. Function switch

6. mA, µA and 10A input jacks

7. COM input jack

8. Positive input jack

9. Backlight button

10. REL button

11. HOLD button

Note: Tilt stand and battery compartment are on rear of unit.

SYMBOLS AND ANNUNCIATORS

•))) Continuity

Diode test

Battery status

n nano (10-9) (capacitance)

µ micro (10-6) (amps)

m milli (10-3) (volts, amps)

A Amps

k kilo (103) (ohms)

F Farads (capacitance)

M mega (106) (ohms)

 Ohms

Hz Hertz (frequency) V Volts

% Percent (duty ratio) REL Relative

AC Alternating current Auto Autoranging

DC Direct current HOLD Display hold

ºF Degrees Fahrenheit ºC Degrees Centigrade

SPECIFICATIONS

Function Range Resolution Accuracy

400mV 0.1mV (0.5% reading + 2 digits)

4V 0.001V

40V 0.01V

400V 0.1V

(1.2% reading + 2 digits)

DC Voltage

1000V 1V (1.5% reading + 2 digits)

400mV 0.1mV (2.0% reading + 10 digits)

4V 0.001V

40V 0.01V

400V 0.1V

(2.0% reading + 5 digits)

AC Voltage

1000V 1V (2.5% reading + 5 digits)

400A 0.1A (1.0% reading + 3 digits)

4000A 1A

40mA 0.01mA

400mA 0.1mA

(1.5% reading + 3 digits)

DC Current

10A 0.01A (2.5% reading + 5 digits)

400A 0.1A (2.5% reading + 10 digits)

4000A 1A

40mA 0.01mA

400mA 0.1mA

(2.5% reading + 5 digits)

AC Current

10A 0.01A (3.0% reading + 7 digits)

4000.1(1.2% reading + 4 digits)

4k0.001k(1.0% reading + 2 digits)

40k0.01k

400k0.1k

4M0.001M

(1.2% reading + 2 digits)

Resistance

40M0.01M(2.0% reading + 3 digits)

Function Range Resolution Accuracy

40nF 0.01nF (5.0% reading + 7 digits)

400nF 0.1nF

4F 0.001F

40F 0.01F

(3.0% reading + 5 digits)

Capacitance

100F 0.1F (5% reading + 5 digits)

5.999Hz 0.001Hz

59.99Hz 0.01Hz (1.5% reading + 1 digits)

599.9Hz 0.1Hz

5.999kHz 0.001kHz

59.99kHz 0.01kHz

599.9kHz 0.1kHz

(1.2% reading + 3 digits)

5.999MHz 0.001MHz

9.999MHz 0.001MHz (1.5% reading + 4 digits)

Frequency

Sensitivity: 0.5V rms <500kHz; 3V rms >500kHz

0.1 to 99.9% 0.1% (1.2% reading + 2 digits)

Duty Cycle

Pulse width: 100µs - 100ms, Frequency: 5Hz to 150kHz

-4 to 1382F

-20 to 750C

0.1<400

1≥400

(3.0% reading + 5C /9F )

(probe accuracy not included)

Temp

(type-K)

Supplied Probe range: -58.0 to 482oF (-50.0 to 250oC)

Note: An optional probe that is rated to the full range of the meter

is available from the www.craftsman.com website.

Note: Accuracy is stated at 65oF to 83oF (18oC to 28oC) and less

than 75% RH.

Note: Accuracy specifications consist of two elements:

(% reading) – This is the accuracy of the measurement circuit.

(+ digits) – This is the accuracy of the analog to digital converter.

Enclosure Double molded, waterproof (IP67)

Shock (Drop Test) 6.5 feet (2 meters)

Diode Test Test current of 0.3mA typical, open

circuit voltage 1.5V DC typical

Continuity Check Audible signal will sound if the

resistance is less than 100(approx.),

test current <0.3mA

Temperature Sensor Requires type K thermocouple

Input Impedance 7.8MΩ

AC Response True rms

ACV Bandwidth 50Hz to 400Hz

Crest Factor ≤3 at full scale up to 500V, decreasing

linearly to ≤1.5 at 1000V

Display 4,000 count backlit liquid crystal

Overrange indication “OL” is displayed

Auto Power Off 30 minutes (approximately)

Polarity Automatic (no indication for positive);

Minus (-) sign for negative

Measurement Rate 2 times per second, nominal

Low Battery Indication “ ” is displayed if battery voltage

drops below operating voltage

Battery One 9 volt (NEDA 1604) battery

Fuses mA, µA ranges; 0.5A/1000V ceramic

fast blow

A range; 10A/1000V ceramic fast blow

Operating Temperature 41F to 104F (5C to 40C)

Storage Temperature -4F to 140F (-20C to 60C)

Operating Humidity Max 80% up to 87F (31C) decreasing

linearly to 50% at 104F (40C)

Storage Humidity <80%

Operating Altitude 7000ft. (2000meters) maximum.

Weight 0.908lb (412g) (includes holster).

Size 7.2” x 3.2” x 2.2” (182 x 82 x 55mm)

Safety This meter is intended for origin of installation use

and protected, against the users, by double

insulation per EN61010-1 and IEC61010-1 2nd

Edition (2001) to Category IV 600V and Category III

1000V; Pollution Degree 2. The meter also meets

UL 61010-1, 2nd Edition (2004), CAN/CSA C22.2

No. 61010-1 2nd Edition (2004), and UL 61010B-2-

031, 1st Edition (2003)

Approvals UL CE

UL Listed The UL mark does not indicate that this product has

been evaluated for the accuracy of its readings.

Otros manuales para 82003

Tabla de contenidos

Otros manuales de Multímetro de Craftsman

Craftsman

Craftsman 82351 Manual de usuario

Craftsman

Craftsman 82354 Manual de usuario

Craftsman

Craftsman 82024 Manual de usuario

Craftsman

Craftsman 82362 Manual de usuario

Craftsman

Craftsman 82337 Manual de usuario

Craftsman

Craftsman 82351 Manual de usuario

Craftsman

Craftsman 82315 Manual de usuario

Craftsman

Craftsman 82312 Manual de usuario

Craftsman

Craftsman 82345 Manual de usuario

Craftsman

Craftsman 82344 Manual de usuario

Craftsman

Craftsman 81079 Manual de usuario

Craftsman

Craftsman 82345 Manual de usuario

Craftsman

Craftsman 82170 Manual de usuario

Craftsman

Craftsman 82141 Manual de usuario

Craftsman

Craftsman 82354 Manual de usuario

Craftsman

Craftsman 82141 Manual de usuario

Craftsman

Craftsman 81079 Manual de usuario

Craftsman

Craftsman 82339 Manual de usuario

Craftsman

Craftsman 82003 Manual de usuario

Craftsman

Craftsman 82005 Manual de usuario

Craftsman

Craftsman 82362 Manual de usuario

Craftsman

Craftsman 82011 Manual de usuario

Craftsman

Craftsman 82139 Manual de usuario

Manuales populares de Multímetro de otras marcas

Agilent Technologies

Agilent Technologies 34420A Manual de usuario

Fluke

Fluke 83 Manual de usuario

Hameg

Hameg HM 8012 Manual de usuario

Mastech

Mastech MY70 Manual de usuario

Steren

Steren MUL-300 Manual de usuario

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manual de usuario

PeakTech

PeakTech 4000 Manual de uso y cuidado

YOKOGAWA

YOKOGAWA 90050B Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manual de usuario

Fluke

Fluke 8846A Manual de operación y mantenimiento

Tempo Communications

Tempo Communications MM200 Manual de usuario

Elenco Electronics

Elenco Electronics CM-1555 Manual de usuario

Mastech

Mastech MS8238C Manual de usuario

SDAR

SDAR 830A, 830B, 830D, 830C Manual de usuario

RS PRO

RS PRO RS-9519BT Manual de usuario

BGS technic

BGS technic 8890 Manual de usuario

Amprobe

Amprobe Hexagon 60 Manual de usuario