Craftsman 320 Series Manual de usuario

Owner’s Manual

Green Rotary Laser Level

Model No.

320. XXXXX

CAUTION: Before using this product, read this

manual and follow all its Safety Rules and

Operating Instructions.

•Safety

•Operation

•Maintenance

•Trouble shooting

Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA

www.craftsman.com

TABLE OF CONTENTS

Warranty………………………………………………........….....…….....

Safety Instructions……………………………………….….……..…......

Description……………………………………………………..................

Operation………………………………………………….............………

Application...........................................................................................

Maintenance…………………………………………………...................

Trouble Shooting…………………………………………….........………

Service Numbers…………………………………………….........………

Page 2

Page 3-4

Page 4-6

Page 6-16

Page 16-17

Page 17-18

Page 18-19

Back Cove

FULL ONE YEAR WARRANTY ON CRAFTSMAN GREEN ROTARY LASER

LEVEL If this CRAFTSMAN digital laser level fails to give complete satisfaction

within one year from the date of purchase, RETURN IT TO ANY SEARS STORE

OR PARTS & REPAIR CENTRE OR OTHER CRAFTSMAN OUTLET IN THE

UNITED STATES FOR FREE REPAIR(or replacement if repair proves

impossible)

If this CRAFTSMAN green rotary laser level is used for commercial or rental

purposes, this warranty applies for only 90 days from the date of purchase.

This warranty gives you specific legal rights, and you may also have other rights

which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Contents

Green rotary laser level, Detector, Remote control, Wall mount base, Detector

mounting base, AC/DC adapter, Green laser enhancing safety glasses.

SAVE THESE INSTRUCTIONS!

READ ALL INSTRUCTIONS!

SAFETY INSRUCTION

WARNING: BE SURE to read and understand all instruction in this manual

before using this green rotary laser level. Failure to follow all instructions may result in

hazardous radiation exposure, electric shock, and/or bodily injury.

CAUTION: Use of controls or adjustments or performance of procedures other

than those specified herein, may result in hazardous radiation exposure.

CAUTION: The use of optical instrument with this product will increase eye

hazard.

IMPORTANT: The following labels are on your tool. They indicate where the laser

light is emitted.

ALWAYS BE AWARE of the

emission point locations when using

the green rotary laser level.

ALWAYS MAKE SURE that any

bystanders in the vicinity of use are made aware of the

dangers of looking directly into the laser.

WARNING! LASER LIGHT. LASER RADIATION.

Avoid Direct Eye Exposure. Do Not Stare into beam.

1. DO NOT remove or deface any product labels. Removing

product labels increases the risk of exposure to laser

radiation.

2. DO NOT stare directly at the laser beam or project the laser beam directly into the

eyes of others. Serious eye injury could result.

3. DO NOT place the digital laser level in a position that may cause anyone to stare

into the laser beam intentionally or unintentionally. Serious eye injury could result.

4. DO NOT use any magnifying optical tools such as, but not limited to telescopes or

transits to view the laser beam. Serious eye injury could result.

5. DO NOT operate the green rotary laser level around children or allow children to

operate the tool. Serious eye injury could result.

6. ALWAYS turn the green rotary laser level “OFF” when not in use. Leaving the tool

“ON” increases the risk of someone inadvertently staring into the laser beam.

7. DO NOT operate the green rotary laser level in combustible areas such as in the

presence of flammable liquids, gases or dust.

8. When using any of the base plates, ALWAYS check to be sure that the tool is

SAFETY INSTRUCTION cont.

securely mounted on the base. Damage to the tool and/or serious injury to the

user could result if the tool falls.

9. ALWAYS use only the accessories that are recommended by Sears for use with

this product. Use of accessories that have been designed for use with other laser

tools could result in serious injury.

10. DO NOT use this green rotary laser level for any purpose other than those

outlined in this manual. This could result in serious injury.

11. DO NOT leave the green rotary laser level “ON” unattended.

12. DO NOT attempt to repair or disassemble the green rotary laser level. If

unqualified persons attempt to repair this laser product, serious injury may result.

Any repair required on this laser product should be performed by authorized

service center personnel.

13. Before plugging in the tool, BE SURE that the outlet voltage supplied is same as

the voltage marked on the tool's power adapter.

14. DO NOT expose power adapter to rain or wet conditions. Water entering the

adapter will increase the risk of electric shock.

15. When operating the power adapter outside, ALWAYS use an outdoor extension

cord marked “W-A” or “W”. These cords are rated for outdoor use and reduce the

risk of electric shock.

16. CAUTION! to reduce the risk of electric shock, use the tool only in dry location.

DESCRIPTION

KNOW YOUR GREEN ROTARY LASER LEVEL (See Fig.1 & Fig.2)

This Craftsman green rotary laser level is a highly versatile tool. It can be hand-held,

wall-mounted (on the wall-mount base included) or leveled on a horizontal surface or

tripod stand (sold separately). It projects a bright pulse green laser ‘dot’ that forms a

line horizontally or vertical dimension in a 360°complete circle. As a 2-beam level, it

can be used to accurately determine square alignment such as when laying concrete

foundations, “squaring off” a deck or porch and when aligning fence and rail

constructions.

This green rotary laser level is easy to use in many applications from simple home

decorating projects to home construction. It will project a level horizontal or vertical

‘line’ that is accurate to ±1/4-inch at 100 feet. (Recommended usable range is 50 feet)

Use the remote control you can conveniently operate your rotary laser when you do

some layout far away within 100 feet. The green laser detector can help you easily

find the laser position within 200 feet even in bright surrounding.

Fig.1

Fig. 2

Wall mount base

Detector mounting base

Laser enhancing

safety glasses

Laser Detector Remote

control

AC/DC

adapter

Side base

4.5V AC/DC

adapter hole

5/8” mounting

hole

Battery

com

artment

Push button

Laser aperture

Y vial

X vial

Z vial

Operation

panel

Level base

Y&Z wheel

“X” wheel

Power bar

indicator

Soft handle

TECHNICAL SPECIFICATIONS

Recommended Use Indoors

Laser Diode Type Green Laser Diode 522-542nm

Laser Class Class IIIa, power output <5mW

Battery

3pcs1.5V “D” batteries for rotary laser level, 1pc 12V

“23A” battery for remote control and 1pc 9V “6LR61”

battery for detector. (all the batteries are not

included)

Working range of laser Maximum 100ft. (30m) without detector, depending

upon light conditions

Maximum 200ft. (60m) with detector

Working range of remote control 100 ft. (30m)

Optimum Operating

Temperature Range 32°F to 104°F (0°C to +40°C)

Accuracy +/-1/4-inch at 100 feet

weight ???

OPERATION

To install batteries for the green rotary laser level (See fig.3)

This green rotary laser level uses three”D” 1.5V batteries. (Sold separately)

Fig.3

1. Press the “Push” button to take out

the battery compartment.

2. Install three new “D” size alkaline

batteries according to the polarity

indicators inside the battery

compartment.

3. Fix the battery compartment into the

tool and push it securely in place.

CAUTION! When fix the battery

compartment into the tool, always MAKE

SURE it has been locked securely.

Damage to the case and/or serious injury

to the user could result if it drops out.

Push to

open

To connect AC/DC adapter to the tool

Fig. 4

The laser level can also be power supplied with

AC/DC adapter besides batteries.

1. Insert the connecting plug into the adapter

hole which locates in the rear of the level as

Fig.4 shown.

2. Plug the AC/DC adapter into the correct

mains supply (120V, 60Hz)

CAUTION! Whenever connect the adapter to

the mains supply, always check if the voltage is

120V, 60Hz. Damage to the adapter or the tool

and/or serious injury to the user could result if

connecting to the other voltage of mains supply.

To turn on/off the rotary laser (see Fig. 5)

Press the Power button to turn on the level; the bright green laser beam will light. The

backlights of the vials will also be light up for easier visibility when leveling or

calibrating the laser tool. To turn off the level, press the button again, the backlights of

the vials will wink twice quickly before shutting off.

If the laser is not operated for rotating or chalk line for one hour after it is turned on, it

will automatically turn to the “Sleeping mode” to save the electricity. The laser will be

shut off temporarily, and the backlights of the vials will flash once each two seconds to

remind you that the tool has not been fully shut off. You can wake up the level within

two hours by pressing any of the buttons on the tool except “the power button” or

using remote control. After two hours of time, the tool will automatically shut off totally.

You can press the power button on the tool to turn on the rotary laser again.

WARNING: When turning ON the Rotary Laser Level, ALWAYS be aware of

protecting the eyes of yourself and those around you. NEVER point the green laser at

anyone’s face, including your own.

Power bar indicator:

The indictor has three LEDs for indicating battery capacity; press the “POWER BAR”

button, the LEDs will be light. It will extinguish automatically in about five seconds. All

the LEDs light up showing the battery has full capacity. The rightest LED begins to

wink showing low battery; it reminds you of replacing batteries or powering it with

AC/DC adapter.

Using the Laser-Enhancing Glasses Provided

This green laser level includes a pair of standard safety glasses that are made of a

laser-light enhancing material. The purpose of these glasses is to improve the viewing

of the tool’s laser line.

WARNING: These glasses WILL NOT protect the eyes from damage that

could result from looking directly into the laser projection.

Adjustment of X&Y wheels to center the bubbles

To level the green rotary laser level, operate as

following instructions:

1. If the Green rotary laser Level is in horizontal

position, adjust the “X”&”Y” wheels. The “X” wheel

controls the X bubble vial, and “Y” wheel control Y

bubble vial. Adjust the two wheels to make sure the

Fig.5

1. Power button: turn on/off the tool.

2. Rotation button: adjust the

rotation speed.

3. Chalk line button: adjust the

length of chalk line.

4. Left button: move chalk line or

laser dot to left position.

5. Right button: move chalk line or

laser dot to right position.

6. Power bar indicator: show battery

capacity.

7. Power bar button: turn on/off the

Power bar indicator

Fig.6

eration

anel

X and Y bubbles are in the centre of each vial. (Fig6)

2. If the Green rotary laser level is in vertical position, adjust the “Y” wheel. The “Y”

wheel controls the Z bubble vial. Adjust the “Y” wheel to make sure the bubble of Z

vial is in the centre of the vial.

NOTE: The Green rotary laser level can be mounted on a tripod (sold separately) or

mounted on the wall mount base by using thread holes located on level base plate or

side base plate.

Level the mounting plate on the tripod base as closely as possible before mounting

the Green rotary laser level. After mounting and securing the level to the tripod base

plate, perform steps 1 and 2 above to level the tool to its new position.

Marking a series of level points

1. Adjust the X&Y wheels to center the bubble of the vials.

2. Turn on the laser

3. Align the laser beam to your target by pressing the left arrow button or right arrow

button.

The tool can be used of marking a series of points either in the horizontal or vertical

directions.

Adjusting the laser rotating speed

1. Place the Green rotary laser level on a horizontal surface or vertical position or on

a tripod stand (sold separately).

2. Level the tool.

3. Press the power button to turn on the level.

4. Press the rotation button once for “fast” speed; twice for” medium” speed; third

time for “slow” speed; or fourth time to stop rotation.

You can choose different speeds depending on different work surroundings. Selecting

the best scan speed for your working

conditions and job requirements gives you a

highly visible level reference line.

Making a chalk line (see Fig.7)

1. Place the Green rotary laser level on a

horizontal surface or on a tripod stand (sold

separately).

2. Level the tool.

Fig.7

3. Press the power button to turn on the level.

4. Press the chalk line button to project a chalk line. Press once to project a longest

chalk line; twice to project a medium chalk line and three times to project a shortest

chalk line.

5. Align the laser beam to your target by pressing the left or right button.

You can get the chalk line either in the horizontal or vertical directions. Press the left

or right button to remove the projecting direction of the chalk line- you do not need to

move the tool and re-level it.

Using the remote control (see fig.8)

Description

The wireless remote control can operate your rotary level within a maximum distance

of 100 feet; the function of buttons on remote control is same as the buttons in

operation panel of the level except for the power button.

Fig.8

1. LED indicator

2. Power button.

3. Rotation button

4. Chalk line button

5. Left button

6. Right button

Power button of the rotary laser level: when the level is power on, push it to turn off

the level; the backlights of the vials will flash twice quickly showing all the circuits are

shut off wholly. Now the remote can not control the tool. To operate the remote control,

turn on the tool first.

Power button of the remote control: when the green rotary laser level is powered on,

push it to make the level enter sleeping mode, at this time the backlights of the vials

will flash once each two seconds to remind you that the tool has not been fully shut off.

You can wake up the level within two hours with remote control after you select “Sleep

mode”. After two hours of time, the tool will automatically shut off totally. Then the

remote can not control the tool. To operate the remote control, turn on the tool with the

power button of the level first.

Tabla de contenidos

Otros manuales de Instrumento de medición de Craftsman

Craftsman

Craftsman 82017 Manual de usuario

Craftsman

Craftsman 320.29939 Manual de usuario

Craftsman

Craftsman 82140 Manual de usuario

Craftsman

Craftsman 82140 Manual de usuario

Craftsman

Craftsman 320.48298 Manual de usuario

Craftsman

Craftsman 82028 Manual de usuario

Craftsman

Craftsman 19741 Manual de usuario

Craftsman

Craftsman CMHT77638 Manual de usuario

Craftsman

Craftsman 82369 Manual de usuario

Craftsman

Craftsman 25466 Manual de usuario

Craftsman

Craftsman CMHT77637 Manual de usuario

Craftsman

Craftsman CMHT77639 Manual de usuario

Craftsman

Craftsman 320.48277 Manual de usuario

Craftsman

Craftsman CMHT77621 Manual de usuario

Craftsman

Craftsman 161.210400 Manual de usuario

Craftsman

Craftsman 73756 Manual de usuario

Craftsman

Craftsman CMHT77620 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario