Craftsman 486.248471 Manual de usuario

Operator's lVianual

Model No, 486,248471

FRONT SCOOP TRACTOR ATTACHMENT

CAUTION:

Before using this product, read

this manuaU and follow aH Safety

RuUes and Operating Instructions.

mMPORTANT: For Missing Parts or

AssembUy Questions Call 1-866-576-8388

• Safety

• Assembly

• Operation

• Maintenance

• Parts

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www=sears=com/c raftsman

PRINTED iN U.S.A, FORM NO. 40089 (11/05)

WARRANTY .................................................................... 2

SAFETY RULES .............................................................. 3

FULL SiZE HARDWARE CHART .................................... 4

CARTON CONTENTS ..................................................... 6

ASSEMBLY ...................................................................... 7

OPERATION .................................................................. 17

MAINTENANCE ............................................................ 18

TROUBLESHOOTING ................................................... 18

REPAIR PARTS iLLUSTRATiON .................................. 20

REPAIR PARTS LiST .................................................... 21

SLOPE GUIDE .............................................................. 23

PARTS ORDERING/SERVICE ......................... Back Page

ONE YEAR FULL WARRANTY

When operated and maintained according to the instructions supplied with it, if this Front Scoop Tractor Attachment fails

due to a defect in material or workmanship within one year from the date of purchase, call 1-800-4=MY=HOME® to arrange

for free repair (or replacement if repair proves impossible).

If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., D817WA, Hoffman Estates, tL 60179

The model number and seria! number will be found on a

decal attached to the bucket.

You should record both the serial number and the date of

purchase and keep in a safe place for future reference.

MODEL NUMBER:

SERIAL NUMBER:

DATE OF PURCHASE:

486.248471

Anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperatetheequipment,

Exercisecautionata!ltimeswhenusingpowerequipment,

® Readthisoperator'smanua!beforeattemptingto

assembleoroperatethescoopattachment,

® Readthevehicleowner'smanua!andknowhow

tooperateyourvehiclebeforeusingthescoop

attachment,

o Nevercarrypassengersinthescoopbucket,Ithas

notbeendesignedtocarrypassengers,

o Neverallowchildrentooperatethevehicleorthe

scoopattachment,

o Donotallowadultstooperatethevehicleorscoop

attachmentwithoutproperinstructions,

® Alwaysbeginwiththetransmissioninfirst(low)and

graduallyincreasespeedasconditionspermit,

® Drivethetractoratreducedspeedoverroughterrain

andhillsidesornearcreeksandditchestoprevent

tippingoverandlossofcontrol,Donotdrivetooclose

toacreekorditch,

® Neverramthescoopintomaterialathighspeed,

® Vehiclebrakingandstabilitymaybeaffectedwith

theattachmentofthisscoop,Donotfillthescoop

tomaximumweightcapacitywithoutcheckingthe

capabilityofthevehicletosafelydriveandstopwith

thescoopattached,

o Beforeoperatingvehicleonanygrade(hill)refer

tothesafetyrulesinthevehicleowner'smanual

concerningsafeoperationonslopes,Referalsotothe

slopeguideonpage23ofthismanual,Stayoff steep

stopes!

® Followmaintenanceandlubricationinstructionsas

outlinedinthismanual,

Lookforthissymboltopointoutimportantsafetyprecautions,Itmeans--Attention?!Become

alert!!Yoursafetyis involved.

Theseaccessorieswereavailablewhentheunitwaspurchased,TheyarealsoavailableatmostSearsretailoutletsand

servicecenters,MostSearsstorescanorderrepairpartsforyouwhenyouprovidethemodelnumbersofyourtractorand

scoop,

WHEEL WEIGHT

JHH

PARTS NOT SHOWN FULL SIZE

LL MM

oo PP

PARTS BAG CONTENTS

Not a!l parts will be needed for fit-up to any one tractor=

Discard unneeded parts after assembly is finished.

RER QT_

A 2

B 2

C 3

D 2

E 6

F 5

G 5

H 3

I 6

J 2

K 2

L 1

M 2

N 2

O 3

P 2

Q 8

R 12

S 5

T 1

U 1

DESCRIPTION

Hex Bolt, 5/8" x 1-1/2"

Hex Bolt, 1/2" x 1-3/4"

Hex Bolt, 1/2" x 1"

Hex Bolt, 3/8" x 1-1/4"

Hex Bolt, 3/8" x 1"

Hex Bolt, 5/16" x 1"

Hex Bolt, 5/16" x 1-3/4"

Hex Bolt, 1/4" x 1-3/4"

Carriage Bolt, 3/8" x 1"

Carriage Bolt, 5/16" x 1"

Carriage Bolt, 1/4" x 3/4"

Slotted Truss Head Bolt, 10-32 x 5/8"

Nylock Nut, 5/8"

Ny!ock Nut, 1/2"

Nylock Jam Nut, 1/2"

Hex Nut, 3/8"

Nylock Nut, 3/8"

Ny!ock Nut, 5/16"

Nylock Nut 1/4"

Hex Nut, 1/4"

Nylock Nut, #10-32

RER

QTY.

DESCRIPTION

Lock Washer, 3/8"

Washer, 1/4"

Washer, 5/16"

Washer, 3/8" (Small)

Washer, 1/2" (Small)

Washer, 3/8" (Large)

Washer, 5/8"

Washer, 1/2" (Large)

Washer, 3/4"

Washer, 1"

Hairpin Cotter, Long

Hairpin Cotter, Short

Cotter Pin, 1/8" 1-1/2"

Cotter Pin, 1/8" x 1-1/4"

Spacer, 1/2"

Spacer, 3/8" Small

Clevis Pin

Compression Spring

Cable Tie

Tilt Stop Bracket

Hose Clip

1, BucketAssembly

2, PinStopBracket

3, LiftFrameAssembly

4, LiftBracketAssembly

5, TiltAnchorAssembly

6, Right(Long)SidePlate

7, Left(Long)SidePlate

8, Right(Short)SidePlate

9, Left(Short)SidePlate

10,DumpControlRod

11,LiftStrapAssembly(2)

12,TiltBracketAssembly

13,AttachmentRod

14,DumpHandleTube

15,LiftHandleTube

16,DumpHandleTubeExtension

17,DumpPivotBracket

18,LiftHandleTubeExtension

19,DumpControlPin

20,LiftCable(Short)

21,DumpCable(Long)

4 5

/13

TOOLS REQUIRED FOR ASSEMBLY

(1)

(2)

(1)

#2 Phillips Screwdriver

Standard Screwdriver

15/16" Wrenches (one should be box-end)

3/4" Wrenches

9/16" Wrenches

7/16" Wrenches

1/2" Wrenches

3/8" Wrench

ADDiTiONAL ITEMS NEEDED

Ruler or Tape Measure

Grease

REMOVE PARTS FROM CARTON

,, Remove the hardware pack and all loose parts from

the carton.

Lay cardboard on floor to help prevent scratching of

painted parts.

Lay out and identify all the parts and hardware as

shown on pages 4 through 6.

5/15" WASHERS (X)

5/16"'

NYLOCK NUT (F 78"x 1ol/4"

/ REX BOLT(D)

3/8" NYLOCK NUT (Q) 3/8" REX NUT(P)

FIGURE 1

ASSEMBLE SCOOP

STEP 1: INSTALL TWO BOLTS

(SEE FIGURE 1)

. Assemble two 3/8" x 1-1/4" hex bolts (D) and 3/8" hex

nuts (P), threading the nut a!l the way onto the bolt

until it is tight against the head of the bolt.

Install a nut/bolt assembly into the bucket assembly

and fasten using a 3/8" nyiock nut (Q). Tighten.

Repeat for the other side.

STEP 2: iNSTALL PIN STOP BRACKET

(SEE FIGURE 1)

, Instal! the pin stop bracket to the top of the bucket

assembly using four 5/16" x 1" hex bolts (F), eight

5/16" washers (X) and four 5/16" nylock nuts (R).

Center the bolts in the slots of the pin stop bracket

and the slots of the bucket. Tighten the bracket so that

it is square with the bucket.

STEP 3: iNSTALL UFT FRAME ASSEMBLY

(SEE FIGURE 2)

,, Apply grease to the mounting surface of the bucket

assembly and the inside of the lift frame arms.

Assemble the lift frame assembly to the bucket

assembly using two 5/8" x 1-1/2" hex bolts (A) and

5/8" nylock nuts (M). Tighten, then !oosen the nuts

1/4 turn, or until the lift frame pivots freely.

5/8" x 1ol/2"

REX BOLT (A)

APPLY

GREASE /"'- ...

APPLY LUFT FRAME

GREASE ASSEMBLY

5/8" NYLOCK

NUTS (M) APPLY GREASE

5/8" x 1ol/2"

REX BOLT (A)

FIGURE 2

STEP 4: iNSTALL LIFT BRACKET ASSEMBLY

(SEE FIGURE 3)

o Assemble the lift bracket assembly to the lift frame

assembly using two 5/8" washers (BB) and 1/8" x

1ol/4" cotter pins (ll).

FIGURE 3

STEP 5: INSTALL TILT ANCHOR ASSEMBLY

(SEE FIGURE 4)

,Assemble the tilt anchor assembly to the lift bracket

assembly using two 1/2" x 1" hex bolts (C) and 1/2"

nyiock jam nuts (O). Tighten.

STEP 6: INSTALL LiFT STRAP ASSEMBLIES

(SEE FIGURE 5)

Loosen the bolts and nuts on the lift strap

assemblies 1/4 turn or until the straps will slide back

and forth. You will retighten them later in step 27.

Turn the lift strap assemblies as shown. Install each lift

strap assembly to an arm of the lift bracket assembly

and then secure with a small 1/2" washer (Z) and a

short hairpin cotter (GG).

Position the lower end of each lift strap assembly to

the outside of the lift frame. Fasten to the upper front

holes in the lift frame using a 1/2" x 1" clevis pin (LL),

1/2" spacer (JJ) and short hairpin cotter (GG) for each

assembly.

NOTE: The lift strap assemblies may be installed in the

rear mounting holes of the lift frame to increase the lift

height, but this will also increase the lifting effort. The

front holes give a lift height of about 6-1/2" and require 28

Ibs. of force to lift a 150 Ib load. The rear holes will give a

lift height of about 8ol/2" and require 35 Ibs. of force.

TILT ANCHOR

ASSEMBLY

1/2" ×1"

HEX BOLT (C)

L{FT

BRACKET

FIGURE 4

1/2" NYLOCK

JAM NUTS (O)

I 112" xl"

I HEX BOLT (C)

LIFT STRAP

SHORT ASSEMBLY

HA_RPUN /-....

COTTER (GG) ""-_

1/2" SPACER (JJ) "\\

UPPER FRONT 1/2" x 1"

MOUNTING HOLE CLEWS PiN (LL)

FIGURE 5 Bucket removed for clarity

STEP 7: INSTALL TILT BRACKET ASSEMBLY

(SEE FIGURE 6 ON NEXT PAGE)

, If you mounted the lift strap assemblies in step 6

to the rear holes instead of the front hoies in the lift

frame, replace the spacer on the tilt bracket assembly

with the smaller 3/8" spacer (KK) from the parts bag

at this time,

Loosen the bolts and nuts on the tilt bracket

assembly 1/4 turn or until the two plates of the

assembly will slide back and forth. You wil! retighten

them later in step 26.

Lightlyapplygreasetotheendofthearmonthetilt

anchorassemblyandinstallthetiltbracketassembly

tothearmusinga1/2"x1"hexbolt(C)and1/2"

nylockjamnut(O),Tighten.Loosenthenut1/4turn,

oruntilthetiltbracketassemblypivotsfreely,

Installa 1/4"x 1-3/4"hexbolt(H)througha1/4"

washer(W)andthenthroughtheendoftheextension

springonthetiltbracketassembly,Next,insta!la1/4"

hexnut(T)allthewayontothethreadsofthebolt,

Finallyinstalltheendoftheboltintotheholeinthe

armofthetiltanchorassemblyandsecureusinga

1/4"nylocknut(S).Tighten.

1/4" NYLOCK NUT (S)

TULTANCHOR

ASSEMBLY_

1/4" HEX NUT (T)

1/2" x 1"

REX BOLT (C)

1/4"'WASHER

APPLY

1/4"'x 1-3/4" GREASE

HEX HOLT (H) 1/2" NYLOCK

JAM NUT (O} T{LT BRACKET

ASSEMBLY

FIGURE 6

STEP 9: iNSTALL DUMP CONTROL ROD

(SEE FIGURE 8)

, Install a 1/8" x 1-1/4" cotter pin (ll) into the inside hole

in each end of the dump control rod. Spread the ends

of the cotter pins and wrap around the rod. Instal! a

5/8" washer (BB) onto each end of the control rod.

Install the dump control rod to the dump pivot bracket

and bucket, Fasten using two 5/8" washers (BB) and

1/8" x 1-1/4" cotter pins (ll), Spread the ends of the

cotter pins and wrap around the rod,

1/8" x 1-114"

COTTER PiN (ii)

5/8" WASHERS (BE)

x 1°1/4"

COTTER

PiNS (H)

118" × 1-1/4"

COTTER PiN (H) DUMP

CONTROL

5/8" WASHERS (BE) ROD

FIGURE 8

STEP 8: iNSTALL DUMP PtVOT BRACKET

(SEE FIGURE 7)

" Install a 1/8" x 1-1/2" cotter pin (HH) to the inside hole

in the shaft shown in figure 7, and then install a 1"

washer (EE) onto the shaft. Apply grease to the end of

the shaft and install the dump pivot bracket assembly

onto the shaft. Install a 1" washer (EE) onto the shaft

and secure it using a 1/8" x 1-1/2" cotter pin (HH).

1/8" x 1ol/2"

COTTER PRN(HH)

/_/' 1" WASHERS (EE)

118" × 1-1/2"

COTTER PmN(HH)

DUMP PUVOT

BRACKET

STEP 10: INSTALL TILT STOP BRACKETS

(SEE FIGURE 9)

, Install a tilt stop bracket (OO) to each side of the

bucket using a 1/4" x 3/4" carriage bolt (K), 1/4"

washer (W) and 1/4" nylock nut (S). Do not tighten

the nuts until step 28.

TULTSTOP

BRACKET

1/4" NYLOCK _--.

NUT (S) 1/4" x 3/4" .j.l*_

114"WASHER (W) CARRmAGEBOLT(K)

FIGURE 9

FIGURE 7

STEP11: iNSTALLLIFTHANDLETUBE

(BEEFIGURE10)

installthelifthandletubeintotheindexbracketusing

two5/16"x1-3/4"hexbolts(G)and5/16"nylocknuts

(R).

FIGURE10

STEP12:iNSTALLLIFTHANDLETUBEEXTENSION

(SEEFIGURE11)

, installthelifthandletubeextensiononthelifthandle

tubeusinga1/4"x 1o3/4"hexbolt(H)and1/4"nylock

nut(S),

LiFT HANDLE

TUBE EXTENSUON

1/4" x 1-314"

HEX BOLT (B)

\%\

FIGURE 11

1/4" NYLOCK NUT(S)

UFT HANDLE

TUBE

STEP 13: iNSTALL LIFT CABLE

(SEE FIGURE 12)

Squeeze the lift trigger and slide the anchor end of the

lift cable (short) into the hole in the trigger, Release

the trigger and guide the cable through the slot in

the bottom of the trigger and trigger housing, Insert

the end of the plastic cable covering into the trigger

housing,

Connect the hooked end of the lift cable into the index

rod, and install the threaded cable adjuster into the

notch in the top of the index bracket, placing a nut on

each side of the notch,

Adjust the cable adjustment nuts so that when the

trigger is squeezed, the bottom of the index rod raises

enough to release from the latched position, The index

rod should also lower far enough to lock in the latched

position when the trigger is released,

Attach the lift cable to the lift handle using three cable

ties (NN),

LiFT TRUGGER

LIFT CABLE (SHORT)

CABLE

ANCHOR

FIGURE 12

Tabla de contenidos

Otros manuales de Accesorios para cortadoras de césped de Craftsman

Craftsman

Craftsman 61102 Manual de usuario

Craftsman

Craftsman 917.249890 Manual de usuario

Craftsman

Craftsman 917.249790 Manual de usuario

Craftsman

Craftsman 247.25000 Manual de usuario

Craftsman

Craftsman 292670 Manual de usuario

Craftsman

Craftsman 917.249662 Manual de usuario

Craftsman

Craftsman 917.248920 Manual de usuario

Craftsman

Craftsman 358.792404 Manual de usuario

Craftsman

Craftsman 486.243152 Manual de usuario

Craftsman

Craftsman 536.330600 Manual de usuario

Craftsman

Craftsman 917.249121 Manual de usuario

Craftsman

Craftsman 917.330772 Manual de usuario

Craftsman

Craftsman 536.249810 Manual de usuario

Craftsman

Craftsman 917.249791 Manual de usuario

Craftsman

Craftsman 486.24226 Manual de usuario

Craftsman

Craftsman Sun Shade 486.24226 Manual de usuario

Craftsman

Craftsman 45-04371 Manual de usuario

Craftsman

Craftsman 917.242450 Manual de usuario

Craftsman

Craftsman 917.248940 Manual de usuario

Craftsman

Craftsman GRASS CATCHER 917.24898 Manual de usuario

Craftsman

Craftsman 917.248900 Manual de usuario

Craftsman

Craftsman 917.249781 Manual de usuario

Craftsman

Craftsman 28906 Manual de usuario

Craftsman

Craftsman 48"MOWER 917.24985 Manual de usuario

Manuales populares de Accesorios para cortadoras de césped de otras marcas

Ariens

Ariens 891008 Manual de usuario

Rover

Rover 108 - 109 Manual de usuario

Toro

Toro 112-5803 Manual de usuario

Snapper

Snapper 1690047 Manual de usuario

Scag Power Equipment

Scag Power Equipment GC-F4 Manual de usuario

RHINO

RHINO 800 Manual de usuario

Exmark

Exmark Quest 126-7506 Manual de usuario

Snapper

Snapper 1685167 Manual de usuario

Cub Cadet

Cub Cadet 19B70029100 Manual de usuario

Stihl

Stihl AMK 043.1 Manual de usuario

MTD

MTD 753-0873 Manual

Toro

Toro 30810 Manual de usuario

Bush Hog

Bush Hog RG60 Manual de usuario

Land Pride

Land Pride RCF2760 Manual de usuario

Simplicity

Simplicity 211 Manual de usuario

Toro

Toro Z Master 116-0231 Manual de usuario

Exmark

Exmark ULTRAVAC QUICK DUMP SYSTEM Manual de usuario

Excel

Excel Two Bag Catcher Manual de usuario