Cortelco 1201 Guía de configuración
O
IM
WNER'S
NSTRUCTION ANUAL
MODEL 1201
Carefully read the instructions in this manual.
Follow all warnings and instructions marked on the unit.
When cleaning, unplug the telephone jack from the wall outlet. Use
a damp cloth. use liquid or aerosol cleaners.
Do not use this equipment near water, eg: near a kitchen sink,
bathtub, washbowl, laundry rub, swimming pool or in a wet
basement.
Install in a protected location. Ensure all lines and cords are away
from foot traffic. place objects on the line cord that may
cause damage or abrasion.
Avoid spilling any liquid on the unit. This may cause internal
shorting, fire or shock and is not covered under your warranty.
Do not overload wall outlets and extension cords as this can result
in the risk of fire or electrical shock.
Never push objects of any kind into this telephone as they can
touch dangerous voltage points or short out parts that could result
in a risk of fire or electrical shock.
Take the phone to a qualified technician when it requires repair
work or service. To reduce the risk of electrical shock, do not
disassemble the telephone. Opening or removing covers can
expose you to dangerous voltages or other risks. Incorrect re-
assembly can cause electrical shock during subsequent use.
Avoid using the telephone during an electrical storm. There can be
a slight risk of electrical shock from lightning.
use the telephone to report a gas leak, if in the vicinity of
the leak.
Unplug this telephone from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
If liquid is spilled into the unit.
If the unit is exposed to rain or water.
If the unit does not operate normally by following the
operating Instructions.
If the unit is dropped or the casing is damaged.
If the unit exhibits a distinct change in performance.
DO NOT
DO NOT
DO NOT
l
l
l
l
l
1.
To reduce the risk of fire, electrical shock, and injury, please follow
these basic safety precautions before you use this equipment.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
7
SAFETY INSTRUCTIONS
4
LOCATION OF CONTROLS
1
6
1
Hook Switch Message lamp
AUTO
MUTE
HOLD
Handset
FLASH
PAUSE
STORE/SET
Volume
LCD display Memory
(M1~M3)
REDIAL
RING
VOL.
VOL.
M1
M2
M3
PAUSE
FLASH
STORE/SET
AUTO
MUTE
HOLD
REDIAL
WALL INSTALLATION
3
Desk tab
position
Wall mount
tab position
diagram 1
Slide the handset tab out and rotate it 180 degrees so that the hook
points up. This will hold the handset in the cradle when the phone is
mounted on the wall.
Remove the desk stand from the phone base (see diagram 2).
Mount the phone on a standard telephone wall jack.
1.
2.
3.
diagram 2
52
10. Hold button
Pause button
To place a call on hold, press and hang up the handset. To retrieve the
call lift the handset or go off hook on any other phone connected to the line.
HOLD
11.
12. Phone resetting
1. Lift the handset.
2. Dial *#0000*#.
3. Hang up the handset.
Pressing this button will insert a 3 second pause in the dialing sequence. This
is intended to be used with memory dialing.
Resetting the phone will erase all memory dial numbers and the redial
memory.
Ringer volume
switch
Flash time
switch
Dialing mode
switch
This switch is located on the bottom of the telephone. For Tone Dialing, set
the switch to the T position. For Pulse Dialing, set the switch to the P position.
This feature allows you to redial the last phone number dialed.
a. Lift handset.
b. Press .
Ringer Volume Switch - There are 3 ringer levels ( , , and ). These may
be selected by this switch on the bottom of the telephone.
1. Dial mode switch
Redial function
3. Mute function
4. Flash button
Flash time switch
6. Ringer volume switch
REDIAL
HI LO OFF
2.
5.
This feature allows you to turn off your telephone's microphone so that the
other party cannot hear you.
Press FLASH instead of pressing the hook switch to activate services such as
Call Waiting or 3-Way Calling, or to activate certain PBX or Centrex features.
You may be required to press other buttons before or after you press .
Refer to the custom calling instructions provided by your local telephone
company or to the operating instructions provided with your PBX.
The initial factory-set flash length is 600 milliseconds, which is appropriate for
most installations. However, two other Flash times are available. Use this
switch on the bottom of the phone to select 100, 300 or 600 mSec.
FLASH
3
OPERATIONS
2
Press the or buttons to adjust the receive volume during a
conversation. There are 4 levels.
There are 3 memory locations ( ~ ).
1. Lift the handset.
2. Press .
3. Dial the number to be stored (Press to insert a pause).
4. Press .
5. Press the desired Memory Button ( ~ ).
1. Lift the handset.
2. Press the desired Memory Button ( ~ ).
1. Lift the handset.
2. Press .
3. Dial the number to be stored (Press to insert a pause).
4. Press .
5. Press the desired Memory Button ( ).
1. Lift the handset.
2. Press .
3. Press the desired Memory Button ( ).
7.
8. One-touch memory
9. Two-touch memory
VOL.+ VOL.-
M1 M3
A. To store a number to memory
STORE/SET
PAUSE
STORE/SET
M1 M3
B.
M1 M3
A. To store a number to memory
STORE/SET
PAUSE
STORE/SET
0~9
B. To dial the number in memory
AUTO
0~9
Volume setting
To dial a number stored in memory
There are 10 two-touch memory locations.
4
Tabla de contenidos
Otros manuales de Teléfono de Cortelco
Cortelco
Cortelco Patriot Guía de configuración
Cortelco
Cortelco Tel-Flash 2554 Manual de usuario
Cortelco
Cortelco 2740 Manual de usuario
Cortelco
Cortelco 3693 Guía de configuración
Cortelco
Cortelco CENTURION Guía de configuración
Cortelco
Cortelco 2720 Guía de configuración
Cortelco
Cortelco Select 3719 Guía de configuración
Cortelco
Cortelco 2750 Guía de configuración
Cortelco
Cortelco Tel-Flash 2500 Guía de configuración
Cortelco
Cortelco Colleague 2201 Guía de configuración
Cortelco
Cortelco 2500XX-VBA-20MD Manual de usuario
Cortelco
Cortelco 3691 Guía de configuración
Cortelco
Cortelco COLLEAGUE 2220 Guía de configuración
Cortelco
Cortelco 915044V0E21J Manual de usuario
Cortelco
Cortelco Patriot 2190 Guía de configuración
Cortelco
Cortelco Colleague 2203 Guía de configuración
Cortelco
Cortelco Tel-Flash 2500 Guía de configuración
Cortelco
Cortelco 2750 Guía de configuración
Cortelco
Cortelco Patriot II 2192 Guía de configuración
Cortelco
Cortelco Patriot II Guía de configuración
