Cornelius Flavor Fusion 620053922 Manual de usuario

Icemaker & Adaptor Hold-Down Kit Installation Instructions

INSTALLATION INSTRUCTIONS

ICEMAKER AND ADAPTER HOLD-DOWN KIT P/N 629096853

FOR FLAVOR FUSION / IDC UNITS ONLY

Instructions for Non-30 Inch Wide Icemaker – Flavor Fusion Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Instructions for 30 Inch Wide Icemakers – Flavor Fusion Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Instructions for Non-30 Inch Wide Icemaker – IDC Series Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Instructions for 30 Inch Wide Icemaker – IDC Series Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Parts Included in the Kit are Shown in Table 1:

Tools Needed:

• Power Drill

• 9/64 in. (.140 in.) Drill Bit

• #2 Phillips Head Screwdriver

INSTRUCTIONS FOR NON-30 INCH WIDE ICEMAKER – FLAVOR FUSION UNITS

WARNING: Failure to follow the installation instructions correctly may result in equipment damage

and/or personal injury.

The Parts shown in Table 2 are NOT Used for this Installation:

1. Remove the two top black side panel screws from both sides of the Flavor Fusion unit (See Figure 1) and

save the screws.

Table 1

Part No. Description Qty.

22127 Icemaker Rear Mounting Plate 2

50904 Silicone sealant 1 tube

620053922 Left Side Adapter Hold-Down Bracket 1

620053923 Right Side Adapter Hold-Down Bracket 1

620518916 Adaptor/Icemaker Side Hold-Down Plate (Flat) 2

620701601 #10-16 S.S. Sheetmetal Screws 12

Table 2

Part No. Description Qty.

620518916 Adaptor/Icemaker Side Hold-Down Plate (Flat) 2

Release Date: June 30, 2008 www.cornelius.com Revision: 1

Icemaker & Adaptor Hold-Down Kit Installation Instructions

Figure 1

2. Locate the two right and left side hold down brackets, shown in Figure 2. These are the brackets with the

bent flange on them.

Figure 2

3. There are two options for installing the brackets, outside of the side panels or behind the side panels, as

shown in Figure 3. Left side of unit is shown in Figure 3.

Figure 3

4. Place the bracket over the adapter lid then re-install the black screws that were removed in Step 1.

Side Panel

Screws

Left Side

Right Side

Straight Edge Goes

to the Rear of the

Dispenser

Icemaker & Adaptor Hold-Down Kit Installation Instructions

Figure 4

5. Repeat Steps 1 through 4 for the opposite side of the dispenser.

6. Using the supplied silicone tube, seal icemaker all around to the adapter top, as shown in Figure 5.

Figure 5

7. Locate the icemaker mounting plates at the rear of the icemaker and position as shown in Figure 6, if plates

are not already installed.

NOTE: Kit contains two plates, both mounting plates must be installed.

Figure 6

8. Using the plate as a template, drill 9/64 in. (0.140 in.) holes into the icemaker base and the dispenser, as

shown in Figure 7.

Flange on bracket

MUST Go Over the

Top of the Adapter

Lid as Shown.

Run a Continuous

Bead of Caulking

Around the Adapter

Top

Icemaker & Adaptor Hold-Down Kit Installation Instructions

CAUTION: Be careful not to drill too deep and/or too fast into the icemaker base and dispenser

wrapper as damage may occur to unseen parts.

Figure 7

9. Install the second mounting plate on the other side of the icemaker base. Using supplied sheetmetal

screws, screw four (4) screws per plate into the icemaker base and dispenser wrapper.

INSTRUCTIONS FOR 30 INCH WIDE ICEMAKERS – FLAVOR FUSION UNITS

CAUTION: Failure to follow the installation instructions correctly may result in equipment damage

and/or personal injury.

The Parts shown in Table 3 are NOT Used for this Installation:

1. Using the supplied silicone tube, seal icemaker all around to the adapter top, as shown in Figure 8.

Figure 8

2. Remove the two top black side panel screws from both sides of the Flavor Fusion unit (See Figure 1) and

save the screws.

Table 3

Part No. Description Qty.

22127 Icemaker Rear Mounting Plate 2

620053922 Left Side Adapter Hold-Down Bracket 1

620053923 Right Side Adapter Hold-Down Bracket 1

Icemaker & Adaptor Hold-Down Kit Installation Instructions

3. Locate the two flat, hold down brackets, shown in Figure 9.

Figure 9

4. There are two options for installing the brackets, outside of the side panels or behind the side panels, as

shown in Figure 10. Right side of unit is shown in Figure 10.

Figure 10

5. Place bracket as shown then re-install the black screws as shown in Figure 11, that were removed in Step 1.

Figure 11

6. Using the plate as a template, drill 9/64in. (0.140 in.) holes in the icemaker base, as shown in Figure 12.

CAUTION: Be careful not to drill too deep and/or too fast into the icemaker base and dispenser

wrapper as damage may occur to unseen parts.

Insert Screws

Icemaker & Adaptor Hold-Down Kit Installation Instructions

Figure 12

7. Using the supplied sheetmetal screws, screw four (4) screws per plate into the dispenser wrapper and

icemaker base.

8. Repeat Steps 2 through 7 on the other side of the dispenser.

INSTRUCTIONS FOR NON-30 INCH WIDE ICEMAKER – IDC SERIES UNITS

WARNING: Failure to follow the installation instructions correctly may result in equipment damage

and/or personal injury.

The Parts shown in Table 4 are NOT Used for this Installation:

1. Locate the two right and left side hold down brackets, shown in Figure 2. These are the brackets with the

bent flange on them.

2. Position bracket with the straight edge towards the rear of the unit, as shown in Figure 13. Also, the flange

of the bracket must be over the adapter lid, as shown in Figure 4.

Figure 13

3. Using the bracket as a template, drill two 9/64 in. (0.140 in.) holes in the dispenser wrapper.

CAUTION: Be careful not to drill too deep and/or too fast into the dispenser wrapper as damage may

occur to unseen parts.

Table 4

Part No. Description Qty.

620518916 Adaptor/Icemaker Side Hold-Down Plate (Flat) 2

Straight Edge of

Bracket Goes to

the Rear of the

Dispenser

Icemaker & Adaptor Hold-Down Kit Installation Instructions

4. Using supplied sheetmetal screws, screw two (2) screws per bracket into the dispenser wrapper, as shown

in Figure 14.

Figure 14

5. Repeat Steps 1 through 4 for the opposite side of the dispenser.

6. Using the supplied silicone tube, seal icemaker all around to the adapter top, as shown in Figure 5.

7. Locate the icemaker mounting plates at the rear of the icemaker and position as shown in Figure 6, if plates

are not already installed.

NOTE: Kit contains two plates, both mounting plates must be installed.

8. Using the plate as a template, drill 9/64 in. (0.140 in.) holes into the icemaker base and the dispenser, as

shown in Figure 7.

CAUTION: Be careful not to drill too deep and/or too fast into the icemaker base and dispenser

wrapper as damage may occur to unseen parts.

9. Using the supplied sheetmetal screws, screw four (4) screws per plate into the dispenser wrapper and

icemaker base.

10. Repeat Steps 7 through 9 on the other side of the dispenser.

INSTRUCTIONS FOR 30 INCH WIDE ICEMAKER – IDC SERIES UNITS

WARNING: Failure to follow the installation instructions correctly may result in equipment damage

and/or personal injury.

The Parts shown in Table 5 are NOT Used for this Installation:

1. Using the supplied silicone tube, seal icemaker all around to the adapter top, as shown in Figure 15.

Table 5

Part No. Description Qty.

22127 Icemaker Rear Mounting Plate 2

620053922 Left Side Adapter Hold-Down Bracket 1

620053923 Right Side Adapter Hold-Down Bracket 1

Icemaker & Adaptor Hold-Down Kit Installation Instructions

Figure 15

2. Locate the two flat hold down brackets, shown in Figure 9.

3. Position the plate as shown in Figure 16, with the straight edge towards the rear of the unit and the top of

the plate is about ¾ in. above the adapter lid.

Figure 16

4. Using the plate as a template, drill 9/64 in. (0.140 in.) holes into the icemaker base and the dispenser, as

shown in Figure 17.

CAUTION: Be careful not to drill too deep and/or too fast into the icemaker base and dispenser

wrapper as damage may occur to unseen parts.

Figure 17

3/4 in.

Icemaker & Adaptor Hold-Down Kit Installation Instructions

5. Using the supplied sheetmetal screws, screw four (4) screws per plate into the dispenser wrapper and

icemaker base.

6. Repeat Steps 1 through 5 on the other side of the dispenser.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Máquina de hielo de Cornelius

Cornelius

Cornelius I Series Guía de instalación

Cornelius

Cornelius UC150 ICE ONLY Manual de usuario

Cornelius

Cornelius Quantum 1000 Manual de usuario

Cornelius

Cornelius NORDIC ELITE Series Manual de usuario

Cornelius

Cornelius 2306 Manual de usuario

Cornelius

Cornelius Quantum 1000 Manual de usuario

Cornelius

Cornelius 500 - Series Manual

Cornelius

Cornelius IMD GLACIER 500-30 Manual de usuario

Cornelius

Cornelius Nordic CCM0830 1 Guía

Cornelius

Cornelius IMD300-15A Manual de usuario

Cornelius

Cornelius Nordic CCU0300 Series Manual de usuario

Cornelius

Cornelius Adapter Lid Manual de usuario

Cornelius

Cornelius D3030-1 Manual de usuario

Cornelius

Cornelius "I" Series 227 Manual de usuario

Cornelius

Cornelius DPT 230 Suplemento

Cornelius

Cornelius pmnice systems Manual de usuario

Cornelius

Cornelius P/N 629083202 Manual de usuario

Cornelius

Cornelius D100 Manual de usuario

Cornelius

Cornelius IACS224 Manual de usuario

Cornelius

Cornelius Nordic CCM0322 Guía

Cornelius

Cornelius CCM330 Manual de usuario

Cornelius

Cornelius IDC215 Manual de usuario

Cornelius

Cornelius P/N 629087914 Manual de usuario

Cornelius

Cornelius Enduro-300 IntelliCarb Manual de usuario

Manuales populares de Máquina de hielo de otras marcas

Hoshizaki

Hoshizaki KMD-460MWJ Manual de usuario

Sub-Zero

Sub-Zero 315I Instrucciones de uso

Unold

Unold 48945 Manual de usuario

Kenmore

Kenmore 2217402A Manual de usuario

GE XPIO43SCSS Manual de usuario

Hoshizaki

Hoshizaki KMD-901MAH Manual de usuario

Whynter

Whynter FIM-450HA Manual de usuario

U-Line

U-Line UMCR014-SC01A Manual de instalación

Andrew James

Andrew James AJ000522 Manual de usuario

Scotsman

Scotsman CME1356 Manual de usuario

Scotsman

Scotsman ACM 25 Manual de usuario

Kärcher

Kärcher IP 120 Manual de usuario

U-Line

U-Line SS1095 Manual de usuario

Maytag

Maytag MIM1554WRS - Ice Maker Manual de usuario

Hoshizaki

Hoshizaki KM-630MAH Manual de usuario

Princess

Princess Yonanas Manual de usuario

Unold

Unold 48946 Manual de usuario

Electrolux

Electrolux E15IM60GP Manual de usuario