Cornelius 440000902 Manual de usuario

Este manual sirve para los siguientes modelos

4

Tabla de contenidos

Otros manuales de Dispensador de bebidas de Cornelius

Cornelius

Cornelius IDC 255 Manual de usuario

Cornelius

Cornelius UC-20 Guía de configuración

Cornelius

Cornelius FCB V2 Especificaciones

Cornelius

Cornelius IntelliCarb Cold Beverage Dispenser Guía de instalación

Cornelius

Cornelius 3030 AK 6 Manual de usuario

Cornelius

Cornelius PRISM Manual de usuario

Cornelius

Cornelius 1522 Manual de usuario

Cornelius

Cornelius TRIAD-150 Manual de usuario

Cornelius

Cornelius FCB - 2 Flavor Manual de usuario

Cornelius

Cornelius 1522 Manual de usuario

Cornelius

Cornelius VIPER 4 FLAVOR Manual de usuario

Cornelius

Cornelius IDC PRO 255 Manual de usuario

Cornelius

Cornelius Flavorfusion Ice Drink Dispenser with Flavor... Manual de usuario

Cornelius

Cornelius ED 300 BC Manual de usuario

Cornelius

Cornelius Focus CG5052-0308 Manual de usuario

Cornelius

Cornelius VIPER 2 FLAVOR Manual de usuario

Cornelius

Cornelius ENDURO-175 Manual de usuario

Cornelius

Cornelius Enduro 150 8 Valve Manual de usuario

Cornelius

Cornelius FCB V4 Especificaciones

Cornelius

Cornelius Enduro ED-250 BCP Manual de usuario

Cornelius

Cornelius VANGUARD 245 Manual de usuario

Cornelius

Cornelius Agitator Motor 569000207 Manual de usuario

Cornelius

Cornelius A8661 Guía de configuración

Cornelius

Cornelius IDC PRO 255 Manual de usuario

Manuales populares de Dispensador de bebidas de otras marcas

PEGAS

PEGAS Evolution Manual de usuario

Ugolini

Ugolini MT micro Manual de usuario

Bunn

Bunn SLCA-7 Instrucciones de instalación

Gekkeikan

Gekkeikan Sake Machine Manual de usuario

Olympia

Olympia DH709 Manual de usuario

Marco

Marco ECOSMART PB10 Manual de usuario

Marvel

Marvel ML24BN Series Manual

Cecilware

Cecilware 2K-GB-LD Manual

Sure Vend

Sure Vend 673 Manual de usuario

Nostalgia Electrics

Nostalgia Electrics KEG7000SS Manual de usuario

Bunn

Bunn LCR-3 HV Guía de solución de problemas

Servend

Servend SV-200 Manual de usuario

EdgeStar

EdgeStar VBR440 Manual de usuario

CDS AUTOMATEN

CDS AUTOMATEN ML-16C2-C Manual de usuario

Siemens

Siemens GA 3000 Manual de instrucciones y seguridad

Selbach

Selbach Fruit Juice dispenser Manual de usuario

Taylor

Taylor C302NP Manual de usuario

Vinotemp

Vinotemp VT-WINEDISP2 Manual de usuario

Replacing GIB Controller on Quest Juice Dispensers

© 2003-2011, IMI Cornelius Inc. - 1 - Publication Number: 729011138INS

INSTALLATION INSTRUCTIONS

REPLACING GIB CONTROLLER ON QUEST JUICE DISPENSERS

Parts and Tools

Parts List

Kit should includes: 1 each of the following

Tools Required

One - Phillips Screw Driver

!

WARNING:

Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all

power is off to the unit before performing any work.

Failure to comply could result in serious injury, death or damage to the equipment.

Wiring Diagram of GIB Control

If housing and plugs are damaged during disassembly please refer to the drawing below to for proper location of

inputs and outputs and wires. Each plug is keyed for proper placement.

GIBC Field Kit –Quest (P/N 729011138)

1 440000902 Control Ice Bank 120/60 QST/SLJ/UN750/VG245/VNT

2 440000907 P- Housing Elect Plug A GIBC

3 440000908 P- Housing Elect Plug B GIBC

4 440000909 P- Housing Elect Plug C GIBC

5 440000910 P- Housing Elect Plug D GIBC

6 440000919 P- Cover “A”

7 440000920 P- Cover “B”

8 440000921 P- Cover “C”

9 440000922 P- Cover “D”

Release Date: January 10, 2011 www.cornelius.com Revision: B

Replacing GIB Controller on Quest Juice Dispensers

Publication Number: 729011138INS - 2 - © 2003-2011, IMI Cornelius Inc.

Removal of GIB Control

1. Disconnect power from unit.

2. Remove dispensing nozzles.

3. To remove splash panel located at the bottom of the unit

remove two screws left and right side and slide splash panel

forward.

4. To remove top panel open door and locate two screws at

the rear of the panel. Slide top panel forward to release it

from the front.

5. To remove the side panels locate two screws at the rear of

the panel top and bottom and pull off.

6. Locate the plastic wire tie holding the wire harness bundle

together and cut to remove.

Replacing GIB Controller on Quest Juice Dispensers

© 2003-2011, IMI Cornelius Inc. - 3 - Publication Number: 729011138INS

9. Remove plugs from GIBC by pulling connectors from rear of unit. Plugs may be difficult to remove. (NEVER

PULL ON WIRES AS THEY MAY COME LOOSE FROM CONNECTOR BODY). If connector body is damaged

replace with the proper connector body supplied in the kit. Refer to the drawing in the beginning of the installation

sheet for proper connector and wire locations.

10. Reverse the above procedure to reassemble machine.

CAUTION: When reinstalling the new GIBC be sure not to pinch wires between any parts of the

frame. With the side panel off inspect that the wires are free and not trapped where they could

become pinched and short out to the cabinet frame.

NOTE: It is also recommended that before reattaching the panels to the machine reinstall the control

and verify machine functions properly. If any part of the dispenser does not function properly

such as pumps, disconnect power and reinstall GIB control. Be sure connector is seated prop-

erly in connectors.

7. Locate the electrical box, from the front of the machine, and

remove the screw on the right side holding it in place. Grab

the left tab of the box and pull forward.

NOTE: The connectors in the back will tend to give

some resistance when pulling on the box.

8. You will now be able to access the GBIC. To remove slide

module to the right. When box stops push up and pull for-

ward.