Cornelius P/N 629088650 Manual de usuario
IDC Icemaker Adaptor Kit Installation Instructions
© 2005-2010, IMI Cornelius Inc. - 1 - Publication Number: 629088650INS
INSTALLATION INSTRUCTIONS
IDC ICEMAKER ADAPTOR KIT FOR P/N 629088650
FIGURE 1
!
WARNING:
Disconnect power to the unit before installing adaptor following all lock out / tag out procedures established by the
user. Verify all of the power is off to the unit before performing any work. Failure to comply could result in serious
injury, death or damage to the equipment.
!
WARNING:
All of the attachment screws and plates must be installed as directed in this manual. Failure to comply could result in
serious Injury, Death or Damage to the equipment.
Bar
Icemaker
Adaptor kit
Revision Date: August 3, 2010 www.cornelius.com Revision: D
IDC Icemaker Adaptor Kit Installation Instructions
Publication Number: 629088650INS - 2 - © 2005-2010, IMI Cornelius Inc.
1. First step is to position and secure the kit to the dispensing unit. Whenever possible, this should be
done prior to lifting the dispenser onto the counter to allow sufficient access and also provide easier
and faster installation.
FIGURE 2
2. Place ice maker support rail into the front set of pockets in the ice bin as shown in Figure 2.
3. Place bar into first set of pockets inside the ice bin.
4. Place Icemaker Adaptor Kit on top of unit.
5. Place icemaker on top of kit. DO NOT slide icemaker into position on the lid.
6. Apply a continuous bead of NSF International (NSF) listed silastic sealant (Dow 732 or equivalent),
supplied in kit to seal the icemaker to the top of the adapter kit. All excess sealant must be wiped
away immediately.
ICE MAKER
SUPPORT RAIL
IDC Icemaker Adaptor Kit Installation Instructions
© 2005-2010, IMI Cornelius Inc. - 3 - Publication Number: 629088650INS
7. Assemble bin stat to icemaker, as shown. The bin stat must not interfere with the agitator rotation
and not be in the path of ice falling from the icemaker.
FIGURE 3
IDC Icemaker Adaptor Kit Installation Instructions
Publication Number: 629088650INS - 4 - © 2005-2010, IMI Cornelius Inc.
8. The next step is to secure the icemaker to the kit. Use the brackets (supplied) as templates to drill
four 9/64” (.140” Dia.) holes into the adapter kit (2 per side). When drilling holes, the maximum
distance from the back of the kit is 7.50 inches (refer to Figure 4). Failure to comply will result in
damage to the sliding arm mechanisms internal to the kit. Drill four holes of the same diameter into
the icemaker (2 per side). Ensure the location of the brackets will not damage the kit or the
icemaker prior to drilling any holes. USE EXTREME CAUTION NOT TO DRILL INTO ANY OTHER
COMPONENTS. Drill depths should not go further than the thickness of the material being drilled
(just enough to go through). Secure the two brackets using the screws provided.
FIGURE 4
For optimal performance, do not fill ice bin more than 2/3 capacity (maximum fill is 4” below top of bin).
Applies to IDC 255 models only.
DETAI L “A”
U
DETAIL A
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Adaptador de Cornelius
Cornelius
Cornelius ED-300 Manual de usuario
Cornelius
Cornelius P/N 629087002 Manual de usuario
Cornelius
Cornelius P/N 629088733 Manual de usuario
Cornelius
Cornelius ED 2 Series Manual de usuario
Cornelius
Cornelius P/N 629088756 Manual de usuario
Cornelius
Cornelius 629096828 Manual de usuario
Cornelius
Cornelius 255 Manual de usuario
Cornelius
Cornelius Pressurized Liquid Base Beverage Dispense... Manual de usuario
Cornelius
Cornelius ED Manual de usuario
Cornelius
Cornelius P/N 629088662 Manual de usuario
