Corega BAR-WL Hoja de especificaciones
Trademarks
CoregaTM is a trademark of Corega Holdings KK., Japan.
Other trademarks, brand and product names are acknowledged as
trademarks of their respective holders. Information is subject to
change without notice.
All rights reserved.
617-00041-01
BAR-WL
BROADBAND
WIRELESS ROUTER
GET CONNECTED
HUBS • SWITCHES • ADAPTERS • WIRELESS LAN • USB • KVMs • MEDIA CONVERTERS • ROUTERS
ENGLISH: Pg 1-28
DEUTSCH: Pg 29-56
ITALIANO: Pg 57-84
ESPAÑOL: Pg 85-112
FRANÇAIS: Pg 113-140
русский:Pg 141-168
ENGLISH
1
Table of Contents
Technical Specifications 2
FCC Interference Statement 3
CE Declaration of Conformity 3
Features of the BAR-WL Wireless Router 3
1. Installing the BAR-WL Wireless Router 3
1.1 Package Contents 3
1.2 Front Panel LEDs 5
1.3 Rear Panel & Connections 5
1.4 Before connecting your BAR-WL Wireless Router 6
1.5 Computer System Requirements and Setup 7
1.6 Installing the BAR-WL Wireless Router 7
2. Internet Access 7
2.1 Prepare your network information 7
2.2 Web-based User Interface 8
2.3 Initial Configuration - Setup 9
2.3.1 OnePage Setup with DHCP WAN 9
2.3.2 OnePage Setup with Static IP on the WAN 11
2.3.3 OnePage Setup with PPPoE on the WAN 12
2.4 Device Administration Settings 13
2.5 Wireless 14
2.6 DHCP Configuration 15
2.7 Static Routing 16
2.8 DDNS 17
2.9 Virtual Server 18
2.10 Special Applications 19
2.11 DMZ 20
2.12 Access Control 21
2.12.1 IP Address 21
2.12.2 URL Access Setting 22
2.12.3 MAC Address Filter 23
2.13 Status Monitor 23
Appendix A.1: Installing TCP/IP 24
Appendix A.2: Fixed (Static) IP Addresses Configuration 27
ENGLISH
2
Dimensions
175mm (L) x 117mm (W) x 32mm (H)
Weight
378g
Interface Ports
1 x RJ45 10BaseT/100BaseTX WAN port (Auto MDI/MDIX)
4 x RJ45 10BaseT/100BaseTX LAN ports (Auto MDI/MDIX)
Standards Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.11b Wireless
IEEE 802.3x Flow control
Antenna
External
Frequency Range
2.4-2.497GHz
DSSS- Direct Sequence Spread Spectrum
Channels
11 Channels (US, Canada)
13 Channels (Europe)
14 Channels (Japan)
Data Transmission Rate
11Mbps / 5.5Mbps / 2Mbps / 1Mbps Auto Fall-back
Access Mode
Infrastructure mode
Data Security
Provides both 64-bit and 128-bit WEP Encryption
Output Power
18dBm (average)
Receiving Sensitivity
84dBm@11M
Coverage Area
Indoors: Up to 50M (165 ft.) @ 11Mbps
Up to 80M (265 ft.) @ 5.5Mps or lower
Outdoors: Up to 150M (500 ft.) @ 11Mbps
Up to 300M (1000 ft.) @ 5.5Mps or lower
(Depending on environment)
Management
Web-based GUI Management
Operating Environment
Operating Temperature: 0 ~ 40°C degrees
Storage Temperature: -20 ~ 60°C degrees
Humidity: 0 ~ 90% non-condensing
External Power Adapter
5VDC @ 2.5A
Agency Approvals
FCC Class B
CE Class B
GOST
Warranty
2 Years
TECHNICAL SPECIFICATIONS
ENGLISH
3
REGULATORY COMPLIANCE
FCC Interference Statement
This device complies with Part 15 of FCC rule. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
This Broadband Wireless Router has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which is
found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment or device.
• Connect the equipment to an outlet other than the receiver’s.
• Consult a dealer or an experienced radio/TV technician for assistance.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled anvironment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body.
CE Declaration of Conformity
This equipment complies with the specifications relating to electromagnetic compatibility, EN 55022/A1 Class B, and EN 50082-1.
This meets the reasonable protection requirements set ou in the European Council Directive on the approximation of the laws of
the member states relating to Electromagnetic Compatibility Directive (89/336/EEC).
4
ENGLISH
1. Installing the BAR-WL Wireless Router
This chapter describes un-packing, familiarization, and the hardware installation of the BAR-WL Wireless Router.
1.1 Package Contents 1 x BAR-WL Wireless Router
1 x External Power Adapter
1 x Wall Mount Kit (2 screws and 2 wall plugs)
4 x Self Adhesive Rubber Feet
1 x Vertical Desk kit
1 x Ethernet Cable
1 x Installation Guide
Features
Your BAR-WL Wireless Router provides the following features:
• Allows multiple users to access Internet at the same time using a single public IP Address.
• Allows users on Ethernet LAN and wireless LAN to transfer data to each other through wireless-to-wire bridge.
• Provides wireless access roaming, best access point selection, loading balance, network traffic filtering included in wireless
roaming function.
• Provides 64bits/128bits key WEP (Wired Equivalent Privacy) wireless data encryption to secure wireless communication.
• Fully supports 802.11 open and shared key authentication.
• Integrates four switched 10/100BASE-T/TX auto-sensing ports.
• Uses NAT to allow all of your network’s PCs to connect to the Internet using only one IP address.
• Supports PPPoE that enable users to seamlessly connect to ISPs with the user familiar “dial-up” type connection interface.
• Built-in web-based user interface for easy configuration and management.
• Supports DHCP client to receive both a dynamic IP Address and a fixed IP Address from ISP.
• Built-in DHCP server to automatically assign and manage LAN IP addresses.
• Block specific users from accessing specified web sites.
• Allows external Internet users to access information from the internal target host by setting the Virtual Server.
• Provides unrestricted two-way communication between one PC on your LAN and certain Internet services like conferencing,
video and gaming applications.
ENGLISH
5
1.2 Front Panel LEDs
The following figure shows the front view of the BAR-WL Wireless Router.
• PWR (Power) Green Steady on when power is on.
• DIAG (Diagnostic) Red Light up during power on self-check. Not lit in normal operation.
• WLAN (Wireless LAN)
Enable: Green Steady on when AP (Access Point) is enabled.
Activity: Green Blinking when data is following through AP.
• WAN (WAN port)
Link: Green Steady on when ADSL/Cable Modem is properly connected.
Activity: Yellow Blinking when data is following through WAN port.
• LAN (LAN ports)
Link/Act: Green Steady on when link is up and it operates at 100Mbps.
Yellow Steady on when link is up and it operates at 10Mbps.
Green/Yellow Blinking when data is following through this LAN port.
FD/Col: Green Steady on when it operates at full duplex mode.
Off at half duplex mode.
Blinking when collision is occurred on this port.
1.3 Rear Panel & Connections
The following figure shows the rear view of the BAR-WL Wireless Router.
•Init Press the Initialization button quickly to reboot and re-initialize the device. Press the Initialization button of
longer than 3 seconds to clear any configuration and reset the router back to factory default values.
•WAN This port is for connecting to the Wide Area Network ADSL or Cable Modem.
• LAN 1-4 These ports are used to connect computers and peripherals to the BAR-WL.
• Power This socket is used to connect the external power supply to the router.
1
Link
Act Link/Act
LANWANWLAN
Col/Fdx
100M
2 3 4
Power
Power WAN 1 2 3 4 Init
ENGLISH
6
1.4 Before connecting your BAR-WL Wireless Router
Before you connect your BAR-WL Wireless Router, Corega recommend that you download installation instructions particular to
your ISP from the Corega website. These instructions will inform you how to configure the BAR-WL to work with your ISP.
www.corega-international.com
Select the knowledge base
• Enter BAR-WL in the Sub-product category, and the name of your ISP in the Search Text field.
• Press ‘Search’.
In addition, Corega recommend that you visit the URL support site of your ISP, and download and print any information they have
on your type of connection.
Some ISPs will require the user to enter the MAC address of the equipment connected to the ADSL/Cable modem. The MAC
address of the WAN port of the BAR-WL is on the base of the router. The MAC address will be of a format:
000941 2E2ACB
ENGLISH
7
1.5 Computer System Requirements and Setup
To connect to the Internet, an external ADSL or Cable modem and an Internet access account from an ISP are required. In order to
operate with the BAR-WL Wireless Router, each PC that is to be connected should have the following things installed:
• Ethernet NIC (Network Interface Card: a 10Base-T or 10/100Base-T/TX Ethernet card), or wireless client card for wireless
connection.
• System OS: Windows 95, Windows 98, Windows NT4.0, or Windows 2000, or Windows XP.
• TCP/IP network protocol.
• Web browser, such as Microsoft Internet Explorer 4.0 or later, or Netscape Navigator 4.0 or later.
Note! If your computer does not have TCP/IP installed, please read Appendix A before continuing with the installation.
1.6 Installing the BAR-WL Wireless Router
Corega recommend that to initially configure the BAR-WL Wireless Router, that you connect a computer to the router through one
of the LAN ports. (Do not try initially installing the router using a wireless connection).
1. Disconnect the PC from a functioning broadband connection.
2. Connect the WAN port of the router to the ADSL/Cable modem using the original cable.
3. Connect the computer to the BAR-WL Wireless Router using the supplied Ethernet Cable.
4. Connect the power adapter to the BAR-WL Wireless Router.
5. In the majority of cases, the PC will require a Dynamic IP address, which will be automatically allocated by the BAR-WL router
after re-booting your PC. To access any of the setup screens of the router – point a browser at 192.168.1.1. If the router
does not respond, check the IP configuration of the PC – see Appendix A.
2. Internet Access
This chapter describes the procedures necessary too configure the basic functions and to start up your BAR-WL Wireless Router.
2.1 Prepare your network information
Before setting up your BAR-WL Wireless Router, it is suggested you complete the table below with the necessary information which
should be supplied by your ISP.
Computer ADSL/Cable Modem
Existing Ethernet
Connection WAN Connection
WAN Connection
ADSL/Cable Modem
External
Power Adapter
Existing Ethernet
Connection
Corega
BAR WL
Computer
ENGLISH
8
Provided by some ISPs Host Name:
Domain Name:
IP address given by ISP: Dynamic IP Address
Fixed (Static) IP Address:
Subnet Mask:
Default Gateway:
DNS Server Primary:
DNS Server Secondary:
DNS Server Third:
PPP authentication: Login Name:
Password:
WAN Connection Type: Dynamic IP (DHCP):
Fixed (Static ) IP:
PPPoE:
2.2 Web-based User Interface
Your Broadband Wireless Router is designed to use a Web-based Graphical User Interface for configuration. Bring up your web
browser and type http://192.168.1.1 in the browser’s address box. This address is the factory default IP Address of your BAR-WL
Wireless Router. Press “Enter”.
Note! Your computer must have a compatible IP address.
If your computer is using Dynamic IP address, it will have a compatible IP address given to it by the BAR-WL router. (You may
have to reboot the router, then the PC for this to occur).
If your computer is using a Fixed (Static) IP address, then you will have to manually program the computer to have a compatible
IP address – see Appendix A.
The “Username and Password Required”prompt box will appear. Leave the Username and Password empty (default) and
click “OK”.
Tabla de contenidos
Idiomas:
Otros manuales de Enrutador de red de Corega
Manuales populares de Enrutador de red de otras marcas
NETGEAR
NETGEAR FS526T - Switch Manual de usuario
Korenix
Korenix JetNet 5710G Series Manual de usuario
Automated Logic
Automated Logic ZN551 Manual del propietario
Cisco
Cisco ASR 1000 Series Manual del operador
EnGenius
EnGenius ESR-9710 Manual de usuario
Cisco
Cisco 805 Series Instrucciones de funcionamiento y seguridad