Coredy WN300 Hoja de especificaciones
N300 Mini Range Extender
Model WN300
GET STARTED
Preparing.....................................................................
Setup Process.............................................................
Web-Browser Method...............................................
WPS - Method..........................................................
Overview......................................................................
Using as a Extender...................................................
When to Use Your Extender......................................
How the Extender Works..........................................
Power on the Extender.............................................
Connect to an Existing WiFi Network.......................
Method 1: Connect with a web browser................
Method 2:Connect with WPS ...............................
Connect an Ethernet-Enabled Device.......................
Using as a Access Point............................................
Cable Your Fxtender.................................................
Using as a Router.......................................................
Change the Extender Settings..................................
To change the admin password...............................
To set up the time of Extender.................................
Allow or Block Access to Your Network...................
Save/Reload your Router setting.............................
Update the Router Firmware...................................
Hide extender's wireless network............................
TROUBLESHOOTING................................................
1
1
1
2
3
5
5
5
6
7
7
9
11
12
13
15
19
19
19
20
22
22
23
25
User Manual
Quick Installation Guide
01
WPS - Method:
You can also use the WPS function as an alternative
Set-up method, if you have a WPS button available on your
primary router.
Hold the WPS button of your Primary Router/WiFi AP till
the WPS LED starts blinking.
Press and hold the WPS 3 seconds on the Rear Panel.
Once WPS light starts blinking on it as well, please wait for
a minute for The primary router/AP and the Extender
WN300 to pair up and then connect to the "Coredy
WN300_EXT" SSID in your Smart Phone using your
primary router's WIFI password.
6. Enter your Router's/AP's WIFI password in the
Password/WIFI Key/Security key column and click on
"Apply"
7. In the next window, you'll see the reboot process with a
Bar. When the Bar reaches 100%, (Leave the device for
1 minute to let it reboot itself).
8. Open the list of available networks again using your
smartphone. Find out the New SSID "Coredy
WN300_EXT" and connect with it using the same
password as of your primary router/AP.
9. If the internet works, unplug Coredy WN300 and plug it
halfway between your Router and the Device intended
for the internet usage/dead zones in your home where
you were getting low to no WIFI signals.
02
Package Contents:
Rear Panel
The Coredy WN300 WiFi Range Extender is a network
device with multifunction, which can be using for increasing
the distance of a WiFi network by boosting the existing WiFi
signal and enhancing the overall signal quality over long
distances. An extender repeats the signals from an
existing WiFi router or access point.
The Coredy WN300 WiFi Range Extender also can be used
as an Access Point or Router.
Coredy WN300 Mini WiFi Range Extender x 1
Quick Installation Guide x 1
User Manual x 1
RJ-45 Networking Cable x 1
Reset Pin x 1
Some computer required to type the passwork (pin number
on the label) during the initial login.
WiFi AP/PEPEATER
Input:100-240V~
50/60Hz.0.3A
MAC:80:3F:5D:93:6B:46
PIN:96612545
MADE IN CHINA V3
WN300 REV.B3(W8)
SN:19713005300371
Default IP:192.168.10.253
User&Password:admin
MAC:80:3F:5D:93:6B:46
PIN:XXXXXXXX
Overview
User Manual
03
LAN LED
LAN Port WAN/LAN Port
WAN LED
WPS LED WiFi LED
POWER LED
WPS Button
RESET Button
WPS
RESET
LAN WAN WPS WiFi POWER
LED Descriptions
LED Description
Power Lit green. The router is starting.
Off. Power is not supplied to the router.
Wi-Fi Blinking. Wi-Fi radio is operating.
Off. Wi-Fi radio is turn off.
WPS
Blinking. Press and hold the WPS 3 seconds on the Rear
Panel lets you use WPS to join the WiFi network without typing
the WiFi password. The WPS LED blinks light green during this
process.
Off. WPS is not enabled.
WAN
Lit green. The extender has detected an Ethernet cable
connection to the AP or other device.
Blinking fast. The port is sending or receiving traffic.
Off. No Ethernet cable is connected.
LAN
Lit green. The extender has detected an Ethernet cable
connection to the AP or other device.
Blinking fast. The port is sending or receiving traffic.
Off. No Ethernet cable is connected.
04
We recommend that you connect through the extender
network only when the WiFi device is in a “dead zone”
where connection from the existing network is poor or
nonexistent. Data traffic routed through the extender is
inherently slower than traffic routed directly from the
network.
When to Use Your Extender
The extender works like a bridge between a WiFi router (or
a WiFi access point) and a WiFi device outside the range of
the WiFi router. The extender performs two main jobs:
The extender connects to a working WiFi network.
When the extender connects over WiFi to an existing
network, it functions as a network client, similar to how a
WiFi device connects to a network.
How the Extender Works
Using as a Extender
The extender acts as an access point for WiFi devices.
The extender broadcasts its own WiFi network that WiFi
devices can join. In its role as an access point, the
extender performs tasks that WiFi routers do, such as
broadcasting its network name (SSID).
The extender must do each of these jobs so that both
ends of the bridge are in place.
05
Boosts the range of your
existing WiFi and creates
a stronger signal in hard
to reach areas.
WiFi Range Extender
sometimes your router
does not provide the WiFi
coverage you need
Existing WiFi
Power on the Extender
Plug the extender into an electrical outlet, place
your extender in the same room as your WiFi
router.
Proximity to the WiFi router is required only during
the initial setup process.
1
06
Method 1. Connect with a web browser.
Method 2. Connect with WPS. For more information,
see Method 2: Connect with WPS. For more
on page 8.
Connect to an Existing WiFi Network
To extend the range of your WiFi network, you
must connect the extender to your existing WiFi
network. You can do this in one of two ways:
2
1. Use a WiFi network manager on a computer or mobile
device (recommended) to find and connect to the extender
WiFi network “Coredy WN300” , type the password (PIN
number) on the label of rear panel extender if required.
2. Launch a web browser, enter http://192.168.10.253/ or
http://ap.setup/ in the address field of the web browser,
when prompted, enter admin for the user name and
admin for the password, both in lowercase letters.
3. Click the Repeater in the Mode Wizard field.
LAN WAN WPS WLAN POWER
WPS
MAC:80:3F:5D:93:6B:46
PIN:XXXXXXXX
Method 1: Connect with a web browser
07
Refresh
Wizard -- Repeater mode
SSID
Your Target Network a0:21:b7:bf:9f:c8 B+G+N WPA2 - PSK 100%
6
Mac Channel Encrypt Signal Select
Select
4. Click the Select button to choose a WiFi network to extend
5. In the Key (Network password) field, type the existing WiFi
network password (also called the passphrase or security
key) and click the Save&Reboot button, wait 1 minute to
reboot the extender.
When the extender connects to your existing WiFi network
successful, the extender’s new WiFi network name will
change to “Coredy WN300_EXT”, confirm it on your
computer or WiFi device.
If the extender could not connect to your existing WiFi
network, make sure you type the correct password of your
existing WiFi network and try again.
6. Unplug the extender and move it to a new location that is
about halfway between your router and the area with a
poor router WiFi signal.
Note: Click the Refresh button if the wireless Network list
couldn't loads completely or successfully.
LAN WAN WPS WLAN POWER
WPS
WLAN WAN LAN1 LAN2 LAN3 LAN4 WPS
08
7. Using a smart phone to help you choose a spot where the
extender-to-router connection is optimal.
8. If there is not full WiFi signal on your smart phone , plug
the extender into an outlet closer to the router and try
again.
Keep moving the extender to outlets closer to the router
until the full WiFi signal on smart phone.
The location that you choose must be within the range of
your existing WiFi router network.
Press the WPS button on the front panel of the
extender.
The WPS LED blinks.
Method 2: Connect with WPS
Wi-Fi Protected Setup (WPS) lets you join a
secure WiFi network without typing the network
name and password.
Note: WPS does not support WEP network security. If
you are using WEP security, follow the instructions in
Method 1: Connect with a web browser on page 6.
9. Plug the extender into an electrical outlet in an elevated
location and minimizing the number walls and ceilings
between the router and your other devices.
10. Reconnect your computer or WiFi device to the new
extended WiFi network.
Tabla de contenidos
Otros manuales de Extensor de Coredy
