Cooper Security i-On 40 Manual de usuario
Security System
User Guide
Page 2
© Cooper Security Ltd. 2010
Every effort has been made to ensure that the contents
of this book are correct. However, neither the authors
nor Cooper Security Limited accept any liability for loss
or damage caused or alleged to be caused directly or
indirectly by this book. The contents of this book are
subject to change without notice.
Printed and published in the U.K
Part Number 12003622
Warning: Mains voltages are
present inside control unit. No
user serviceable parts inside.
Contents
After an Alarm ................................................... 3
To Silence the Siren: ........................................... 3
Setting the System Using an Access Code or Tag: ... 4
Unsetting the System: ........................................ 5
Setting/Unsetting Partitions: ................................ 6
Quick Set: ......................................................... 8
Using a Radio Keypad .......................................... 9
Setting .......................................................... 9
Unsetting ...................................................... 9
Silencing an Alarm .......................................... 9
Using a Proximity Tag With a Radio Keypad ........ 9
Setting by Remote Control ................................... 9
Unset by Remote control ..................................... 9
If The System Will Not Set ............................... 9
If the System Will Not Set ................................... 10
Alerts (Why is it Beeping?) ................................... 10
To see the cause of the alert: ........................... 10
Administration ................................................... 11
Entering the Menu .......................................... 11
Omitting Zones .............................................. 11
Change Your Access Code ................................ 11
View the Log .................................................. 11
Speech Messages ............................................... 12
Acknowledging a Speech Message ..................... 12
Turn the Chimes On/Off ................................... 12
Activate User Output ....................................... 12
Page 3
1. Make sure it is safe to
enter the premises:
After an Alarm
If the siren is sounding then the system has started an alarm. If
you have one, the strobe will also be fl ashing.
Take Care! Intruders may be present.
To Silence the Siren:
OR present your tag.
2. Either key in your access
code
3. Press to reset the sys-
tem.
4. The system returns to
standby, and is ready to
set again.
The siren stops.
The bottom line of the
display shows the fi rst
zone to alarm.
Enter Access Code
(** )
Press tick to Reset
Burg Z04 Alarm
i-on40
12:20 11/09/2009
(The top line may show the
installer’s name.)
Before you can set the system again:
Notes:
The alarm system may be connected to a communications
network, and send alarm messages to one or more alarm
receiving centres. If the alarm started by accident, phone
the relevant centres and tell them.
The control unit logs the alarm information. You can re-
set the system (step 4 above) without losing information
about the cause of the alarm. See page 11 for instructions
on how to read the log.
If the display
shows:
Call Installer:
Burg Z04 Alarm
Contact your alarm installer.
They will reset the system
for you.
Call ARC: Quote 1234
****
Make a note of the number
on the display after the
word “Quote” and contact
your alarm receiving centre
(ARC). They will ask you
for the number and tell you
what to do next.
Page 4
1. Make sure the system is
idle. Secure all the win-
dows and doors.
3. Press or to select
the option you want.
4. Press .
5. Leave by the designated
exit door.
OR present your tag.
The keypad sounds the exit
tone (a continuous tone).
The top line of the display
shows the part of the sys-
tem being set, the bottom
line shows the remaining
exit time (in seconds).
Note: If the system is pro-
grammed to set instantly
make sure you are outside
the protected area before
pressing .
One of four LEDs glows to
show which part of the sys-
tem is set.
Note: The installer may have
disabled the LEDs to ensure
that the alarm system meets
the appropriate standards.
Setting the System Using an Access Code or Tag:
6. At the end of the exit
time the system sets.
The bottom line of the dis-
play shows the fi rst item in
the setting options menu.
The bottom line of the dis-
play shows each item from
the rest of the menu in turn.
As you key in your code the
display shows a “*” for each
digit.
Do this: The display shows:
i-on40
12:20 11/09/2009
Enter Access Code
(** )
Setting Options ↕
A : Full Set
Setting Options ↕
B : Part Set B
Setting: Part Set B
10 to set
i-on40
12:20 11/09/2009
(The top line may show the
installer’s name.)
2. Either key in your access
code
Note: if you want to
stop setting then
press unset.
System Set
followed by:
Page 5
Notes:
You might not be familiar with some of the terms used in
this book.
“Full Set” means that all the detectors in the system are
being monitored. If there is any activity on any detector
then the system will start an alarm.
“Part Set” means that the system is monitoring some
detectors but not others. The installer selects those detec-
tors that should be monitored during a Part Set.
“Partition” is a segment of the whole system that may not
be accessible to some users. Some users can only set a
single Partition. Other users may be able to set two, three
or all four Partitions. See the next page for instructions on
how to set and unset individual Partitions.
1. Enter by the designated
entry door or route.
Go directly to the key-
pad.
OR present your tag.
Unsetting the System:
The keypad stops the entry
tone. The system is unset.
As you key in your code the
disply shows a “*” for each
digit.
Do this: The display shows:
i-on40
12:20 11/09/2009
Enter Access Code
(** )
The keypad sounds the entry
tone (an interrupted tone).
The system starts the entry
timer.
2. Either key in your access
code
When unsetting the system do not stray from the entry route
designated by the installer. If you do so then you will cause
an alarm.
i-on40
12:20 11/09/2009
LEDs “A” to “D” should be
dark, showing that the sys-
tem is unset.
Note: The installer may have
disabled the LEDs to ensure
that the alarm system meets
the appropriate standards.
System Unset
followed by:
Page 6
1. Make sure the system is
idle. If you want to set a
partition, secure all the
windows and doors in
that partition.
3. Press or to show
“Partitions”.
4. Press .
OR present your tag.
Setting/Unsetting Partitions:
The bottom line of the dis-
play shows the fi rst item in
the setting options menu.
“Partitions” is the second or
third item down on the set-
ting options menu.
As you key in your code the
display shows a “*” for each
digit.
Do this: The display shows:
i-on40
12:20 11/09/2009
Enter Access Code:
(** )
Setting Options ↕
Full Set All
Setting Options ↕
Partitions >
Partitions: ↕
Partition 1 U
(The top line may show the
installer’s name.)
2. Either key in your access
code
If the installer has split your system into “partitions” you may
be allocated to more than one of them. In that case you can
set (or unset) each partition independently of all the others.
5. Press or to select
the change that you
want.
The bottom line of the dis-
play shows the possible
states of the fi rst partition:
U = Unset
S = Full Set
P = Part Set
“U>P” = change to Part Set.
“U>S” = change to Full Set.
“S>U” = change to Unset
“P>U” = change to Unset
Partitions: ↕
Partition 1 U>P
6. Press or to show any
other Partitions to which
you have access.
Partitions: ↕
Stores S
Note that the installer may
have given the Partition
a name.
Note: If you enter a partition and start the entry timer (you
can hear the entry tone) then as soon as you enter a valid
access code or tag the system unsets that partition. See
the previous page.
Page 7
The keypad sounds the exit
tone (a continuous tone).
The top line of the display
shows the part of the sys-
tem being set, the bottom
line shows the remaining
exit time (in seconds).
One or more of LEDs marked
“A” to “D” glows to show
which partitions are set.
If a LED fl ashes the Partition
is Part Set. (There may be
a short delay before all the
appropriate LEDs glow.)
Note: The installer may have
disabled the LEDs to ensure
that the alarm system meets
the appropriate standards.
i-on40
12:20 11/09/2009
7. Press or to select
the change you want for
the Partition.
Partitions: ↕
Stores S>U
8. Press when you have
fi nished changing all the
Partitions to which you
have access.
Setting
10 to set
Do this: The display shows:
Notes:
If you want to stop set-
ting then press Unset.
If a Partition is Full Set
then you cannot go di-
rectly to Part Set. You
must unset the Partition
fi rst. If the Partition is
Part Set then you cannot
go directly to Full Set.
You must unset the Parti-
tion fi rst.
Setting/Unsetting Partitions (Continued):
9. Leave by the designated
exit door (if necessary).
Partitions you have chosen
to unset, unset immedi-
ately.
Partitions you have chosen
to set start their exit timer
(or set immediately - see
note.).
10. at the end of the
exit time the selected
Partition(s) set.
Note: If a partition is pro-
grammed to set instantly
make sure you are outside
the protected area before
pressing .
“U>P” = change to Part Set.
“U>S” = change to Full Set.
“S>U” = change to Unset
“P>U” = change to Unset
Page 8
1. Make sure the system is
idle. Secure all windows
and doors.
The keypad sounds the exit
tone (a continuous tone).
The top line of the display
shows the part of the sys-
tem being set, the bottom
line shows the remaining
exit time (in seconds).
One or more of the LEDs
marked glow to show which
part of the system is set.
If a LED fl ashes then a Parti-
tion is Part Set.
Note: The installer may have
disabled the LEDs to ensure
that the alarm system meets
the appropriate standards.
Quick Set:
3. Leave by the designated
exit door.
4. At the end of the exit
time the system sets.
Do this: The display shows:
i-on40
12:20 11/09/2009
Setting: Part Set B
10 to set
i-on40
12:20 11/09/2009
(The top line may show the
installer’s name instead of
“i-on40”.)
2. Press A, B, C or D
While the system is set the
display shows the time and
date.
Quick setting does not require the use of an access code or tag.
The installer must enable this facility for you. (Note that in order
to comply with EN50131 the installer may not be allowed to pro-
vide this facility.)
Page 9
Setting by Remote Control
Note: You must ask your Administrator to
provide a suitably programmed remote con-
trol, see i-on40 Administrator’s Guide.
Secure all your windows and doors.
Make sure the system is idle, and that you
can hear the warning tones from the sound-
ers.
1. Press the appropriate button on the re-
mote control, either full set (A) or part
set (B).
A
B
Transmit
LED
Full Set
Part Set
Unset
Not used
The keypad sounds the exit warning tone.
2. Leave by the exit door and make sure it
is closed properly (if you have not already
done so).
At the end of the exit time the exit tone
stops you should hear a double “beep”
confi rmation tone. The keypad display
shows the message “System Set” for a
few seconds. The installer may also have
programmed your external sounder/
strobe to fl ash briefl y, and one of the key-
pad LEDs to glow to indicate which part of
the system is set.
Unset by Remote control
1. Enter by the designated entry door.
2. Press on your remote control.
The system unsets. At this point the system
displays the standby screen.
If The System Will Not Set
If one of the detectors is still active when you
try to set the system then you will not hear
the exit warning tone.
What happens next depends on how the in-
staller has set up your system.
a) Try pressing A once more on your remote
control. If the installer has programmed
the system to do so then it will carry on
and set, omitting the active detector.
b) If the system will not set on the second
press of button A then you will have to go
to the keypad and set the system from
there.
Using a Radio Keypad
Setting
Secure all your windows and doors. Make
sure the system is idle, and that you can
hear the warning tones from the sounders.
1. Key in a valid access code.
2. Press either A, B, C or D to set the por-
tion of system that you require.
(If you wish to stop setting while the exit
tone sounds, then press .)
The left hand LED glows to show that the
keypad is transmitting.
3. Leave by the exit door and make sure
that it is closed properly.
Unsetting
1. Enter by the designated entry door.
2. Key in a valid access code.
3. Press .
Silencing an Alarm
1. Key in a valid access code.
2. Press .
Using a Proximity Tag With a
Radio Keypad
If you wish to use a Proximity Tag with the
radio keypad in place of an access code, then
hold the tag up against the proximity tag
sensor.
The keypad glows blue and gives a “click” to
show that it has recognised the tag.
Proximity tag
sensor
“Transmit” LED
Note: The radio keypad does not show the
status of the alarm system at all. The left
hand “Transmit” LED glows only to show
that the keypad is sending a command to
the control unit.
Page 10
Alerts
(Why is it Beeping?)
From time to time the control unit may de-
tect that there is a problem with the system.
It will try to inform you of this by starting an
alert. During an alert the rim of the naviga-
tion pad glows red, and the keypad will give
a short “beep” every few seconds.
Red means Alert Press
To see the cause of the alert:
1. Make sure the system is unset and that
the keypad display shows the standby
screen.
2. Press .
The display asks you to key in an access
code.
3. Key in a user access code (or present a
tag).
The bottom line of the display shows a
message describing the most recent ac-
tive alert.
If you press or then the system will
show you any other alerts that may be
active.
4. Either:
Press to acknowledge that you have
read the alert.
If there are no other alerts the rim of the
navigation pad will glow green and the
keypad will return to its’ standby screen.
In addition the keypad will stop beeping.
Or press . The rim of the navigation pad
will stay red and the system will show the
text of the alert the next time you key in
an access code.
Note:
1. The keypad(s) will not beep for short
(less than 10s) interruptions of mains
power. If the cause of an alert goes
away, then the system will remove the
alert message.
2. The system records all alerts in the
log, with the time when you acknowl-
edged them.
i-on16
12:20 11/03/2008
If the System Will Not Set
Normally, the system will set only when all
the detectors are “quiet”, that is: not report-
ing any activity.
If you have the fi nal exit door open, or if
you trigger one of the detectors on your exit
route, then the keypad and internal sounder
will give an interrupted setting tone (this is
normal). Make sure that you close all the
doors on your exit route and the fi nal exit
door as you leave. The interrupted tone will
change to a continuous exit tone, and the
system will set normally.
If you try to set when one or more detec-
tors NOT on your exit route are still active
then the display shows the words “SETTING
FAULTS”. The bottom line of the display tells
you which zone is active, for example:
SETTING FAULTS
Z02 Back door
You can make the system “omit” those active
zones, either while you are setting the sys-
tem (see below) or beforehand (see page 11
for instructions on how to omit zones before
setting the system).
1. Follow the instructions on pages 4 to 7 to
as necessary to set the system.
If any detectors are not yet ready to be
set then the top line of the display shows
2. EITHER Press to carry on setting.
The system sets with the active zones
omitted.
OR Stop the setting process by pressing .
Otros manuales para i-On 40
8
Tabla de contenidos
Otros manuales de Sistema de seguridad de Cooper Security
Cooper Security
Cooper Security i-On 40 Manual de servicio
Cooper Security
Cooper Security Scantronic i-on160EXEUR Manual de servicio
Cooper Security
Cooper Security i-on160EX Manual de usuario
Cooper Security
Cooper Security Homelink 75 Manual de usuario
Cooper Security
Cooper Security Homelink 75 Manual de usuario
Cooper Security
Cooper Security i-On 40 Manual de usuario
Cooper Security
Cooper Security M-Series Manual de usuario
Cooper Security
Cooper Security Menvier300 Manual de usuario
Cooper Security
Cooper Security i-on30EX Manual de usuario
Cooper Security
Cooper Security i-On 40 Manual de usuario
Cooper Security
Cooper Security FOB-2W-4B Manual de usuario
Cooper Security
Cooper Security i-On 40 Manual del propietario
Cooper Security
Cooper Security 9651PD Manual de usuario
Cooper Security
Cooper Security Homelink 75 Manual de servicio
Cooper Security
Cooper Security M-Series Manual de instalación y operación
Cooper Security
Cooper Security I-SD01 Guía de instalación
Cooper Security
Cooper Security Scantronic 9853 Manual de usuario
Cooper Security
Cooper Security i-on16 Guía de instalación
Cooper Security
Cooper Security i-On 40 Manual de servicio
Cooper Security
Cooper Security M-Series Manual de usuario
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario