Cooke WATER WITCH SMART SENSE Instrucciones de instalación
WATER WITCH
SMART SENSE
PRODUCT SUPPORT GUIDE
waterwitch
Electronic Water Leveller
Cooke Industries
P: 1300 652 076
cookeindustries.com.au
waterwitch
Electronic Water Leveller
Product
Support Guide
waterwitch
Electronic Water Leveller
ii
THE WATER WITCH SMART SENSE
Thank you for purchasing the Water Witch Smart Sense electronic
water leveller. The Water Witch has been Australia’s most trusted
auto leveller for more than 25 years and we’re excited to bring this
new model to you. The Water Witch Smart Sense connues our
promise of great reliability and now includes a host of added benets.
The development of the original Water Witch harks back to the 1980s. As a
pool builder I was frustrated with the poor quality and reliability of levellers
at the me. Many prototypes were tested in my shed at home unl we were
comfortable we had developed the highest-quality leveller.
Many years of industry experience and talking to pool builders about what
features they want in an auto leveller guided our development of the Water
Witch Smart Sense. We’re extremely proud of the new unit and its many
addional features.
Importantly, the new Water Witch features full backward and forward
compability with previous models. Any combinaon of Water Witch Control
Box, Sensor and Solenoid will provide a great experience for your pool or
water project.
As always, we promise to deliver the very best product to you. Thank you
for your support and we trust your Water Witch will deliver many years of
reliable service.
Cli Cooke
Managing Director
Product
Support Guide
waterwitch
Electronic Water Leveller
01
INDEX
Compliance noces Page 02
Product applicaons and warnings Page 03
Product components and part numbers Page 04
Control box installaon Page 05
Sensor installaon Page 06
Solenoid valve installaon Page 08
Alternave installaon opons Page 10
Pump out from tank or trough Page 12
Start-up process Page 13
Operang modes Page 15
Manual ll Page 15
Runme log Page 16
Fault log Page 16
Troubleshoong process Page 17
Parameters Page 19
Maintenance & specicaons Page 20
Warranty noce Page 21
Product
Support Guide
waterwitch
Electronic Water Leveller
02
COMPLIANCE NOTICES
Page 1of 4
Australian Certif ication Services P ty Ltd ABN 37 121 022 366
PO Box 627 Jannali, NSW 2226 AUSTRALIA
Phone:+61 2 8521 0726
Email:admin@certif icationservices.com.au
www.certificationservices.com.au
www.jas-anz.org/register
Certificate Number : 4004
Issue Date: 15th May 2019
Issue: 01 Revision: 00
Certificate of Conformity
Australian Certification Services Pty Ltd grants to the WaterMark Approved User:
Nymet Australia Pty Ltd
Trading as Nymet Australia Pty Ltd
the right to use the WaterMark as shown above in conjunction with the Certificate No. on product/s as identified in the
WaterMark Schedule and as listed on the WaterMark database www.abcb.gov.au/Product-Certification/WaterMark-
Certification-Scheme which have been shown to comply with the appropriate Applicable Specification referred to below
and as amended from time to time. The WaterMark User is granted a licence to use the WaterMark subject to the rules
governing the use of the WaterMark.
Product Type:
Solenoid Valve
Product Use:
Water Supply
Brand:
NYMET
Certification Specification/s:
WMTS 030:2016 Solenoid valves
Issue Date
15th May 2019
Paul Greig
Initial Issue Date:
12th December 2005
(GlobalMark)
General Manager
Expiry Date:
2nd July 2023
Certificate No.: 4004
This Certificate is issued by a JAS-ANZ accredited certification body. The ABCB and JAS-ANZ do not in any way warrant,
guarantee or represent that the product the subject of this Certificate conforms to the WaterMark Certification Scheme Rules, nor
accepts any liability arising out of the use of the product. The ABCB disclaims to the extent permitted by law, all liability (including
negligence) for claims of losses, expenses, damages and costs arising as a result of the use of the product(s) referred to in this
Certificate. The WaterMark Certification Scheme is a conformity assessment scheme based on ISO/IEC 17067. This Certificate may
only be reproduced in its entirety
Page 1of 2
Australian Cer tification Services Pty Ltd AB N 37 121 022 366
PO Box 627 Jannali, NSW 2226 AUSTRALIA
Phone:+61 2 8521 0726
Email:admin@certif icationservices.com.au
www.certificationservices.com.au
www.jas-anz.org/register
Certificate Number: 40070
Issue Date: 3rd July 2018
Issue: 02 Revision: 00
Certificate of Conformity
Australian Certification Services Pty Ltd grants to the WaterMark Approved User:
Nymet Australia Pty Ltd
Trading as Nymet Australia Pty Ltd
the right to use the WaterMark as shown above in conjunction with the Certificate No. on product/s as identified in the
WaterMark Schedule and as listed on the WaterMark database www.abcb.gov.au/Product-Certification/WaterMark-
Certification-Scheme which have been shown to comply with the appropriate Applicable Specification referred to below
and as amended from time to time. The WaterMark User is granted a licence to use the WaterMark subject to the rules
governing the use of the WaterMark.
Product Type:
Back Flow Prevention Devices
Product Use:
Water Supply
Brand:
NYMET
Certification Specification/s:
AS/NZS 2845.1:2010 Water supply—Backflow prevention devices Part 1:
Materials, design and performance requirements
Issue Date
3rd July 2018
Paul Greig
Initial Issue Date:
27th March 2017
General Manager
Expiry Date:
2nd July 2023
Certificate No.: 40070
This Certificate is issued by a JAS-ANZ accredited certification body. The ABCB and JAS-ANZ do not in any way warrant,
guarantee or represent that the product the subject of this Certificate conforms to the WaterMark Certification Scheme Rules, nor
accepts any liability arising out of the use of the product. The ABCB disclaims to the extent permitted by law, all liability (including
negligence) for claims of losses, expenses, damages and costs arising as a result of the use of the product(s) referred to in this
Certificate. The WaterMark Certification Scheme is a conformity assessment scheme based on ISO/IEC 17067. This Certificate may
only be reproduced in its entirety
SOLENOID VALVE BACKFLOW PREVENTION VALVE
Product
Support Guide
waterwitch
Electronic Water Leveller
03
PRODUCT APPLICATIONS AND WARNINGS
The Water Witch is used in many dierent applicaons and projects to maintain a minimum
or maximum water level. Some of the most popular applicaons include:
• Swimming pools and spas •
Balance tanks
• Water features and ponds •
Innity edge troughs
• Water / Splash parks • Commercial pools
• Irrigaon projects • Water tanks
Given the many suitable applicaons for the Water Witch, a quality installaon is required
to ensure performance is not aected by site condions or any other factor.
•
The Water Witch is manufactured
and tested to the highest
internaonal standards. Wear
and onsite condions, however,
may cause component failure. All
installaons must include sucient
overow provisions to ensure a
ooding event does not occur.
• Indoor pools and enclosed projects
must also feature sucient overow
provisions to avoid a potenal
ooding event.
• Contact your local water authority
to conrm whether your proposed
Water Witch supply side installaon
complies with the relevant water
regulaons.
• Individual components may need
to be replaced in the future. All
installaons should incorporate
provisions for easy part replacement.
• The Water Witch includes wearing
components that may fail or be
aected by onsite condions. A
visual inspecon of all components
is required at least every month to
ensure the unit is operang correctly.
• The Water Witch is approved for
indoor and outdoor use. However,
consider what eect the environment
may have on the unit when deciding
on an installaon locaon.
Please note the following important project consideraons:
Product
Support Guide
waterwitch
Electronic Water Leveller
04
PRODUCT COMPONENTS AND PART NUMBERS
The reliability and durability of the Water Witch is founded on its simplicity – there
are just three main components and the unit will work well if all components are
funconing correctly and site condions are suitable.
CONTROL BOX
WS345 Water Witch Control Box
SENSOR
WS355 Water Witch Sensor Only – 5m
WS356 Water Witch Sensor Only – 20m
WS357 Water Witch Sensor Only – 30m
WS358 Water Witch Sensor Only – 40m
WS359 Water Witch Sensor Only – 50m
WS360 Water Witch Sensor Only – 60m
SOLENOID VALVE
WS320 Water Witch Solenoid Only
WS330 Water Witch Solenoid Cable Only
WS335 Water Witch Solenoid & Cable
WS340 Water Witch Backow Prevenon Valve
Note – Special order opons are available for sensors up to 250m long.
Product
Support Guide
waterwitch
Electronic Water Leveller
05
The Control Box is the brain of the operaon, connuously receiving signals from the
Sensor to conrm whether the body of water is at the required level or if water needs
to be added to the project.
CONTROL BOX INSTALLATION
• Posion the unit at least 1.2m above
ground level and ensure a consistent
power source is within reach of the
power lead.
• Secure the control box to the desired
posion on a wall or post with the
screws provided.
• Secure the power pack to the wall
or post with the screws provided.
INSTALLATION PROCESS AND CONSIDERATIONS:
NOTE:The Control Box is approved for indoor and outdoor use. However,
locang the Control Box and power pack so they are protected from the weather
will extend their serviceable life.
Product
Support Guide
waterwitch
Electronic Water Leveller
06
SENSOR INSTALLATION
The Sensor sits in a balance line, tank or trough to monitor the water level. A ball oat
inside the Sensor lowers as the water level drops, in turn connecng a light beam between
two LED lights in the top of the Sensor. These lights complete an electrical circuit and the
Control Box opens the Solenoid to add water to the project.
As water is added to the project, the water level rises and the ball oat is pushed to
the top of the Sensor. As the ball intersects the light beam at the top of the Sensor,
the Control Box recognises the full water level. Instead of stopping the ow immediately,
the TIME DELAY adds addional water to the project as dictated by the volume set for
the project.
The Water Witch Sensor is available in standard lengths of 5m, 20m, 30m, 40m, 50m
and 60m. Special order sensors can be manufactured up to 250m long.
Sensor installed in balance line
Balance line to be
300mm below water level
Cable gland to
adjust sensor height
Sensor set to
desired level
50mm balance line
Control
Box
Balance line to extend
300mm above water level
DO NOT GLUE
50mm END CAP
POOL
Product
Support Guide
waterwitch
Electronic Water Leveller
07
INSTALLATION PROCESS AND CONSIDERATIONS:
• The sensor requires a 50mm class 9 or class 12 PVC pipe to be installed as a balance line
from the project’s wall to the pump and lter area. ALWAYS USE 50MM PIPE FOR THE
SENSOR HOUSING TO ENABLE ADEQUATE FLOW AROUND THE SENSOR AND
FUTURE SERVICABILITY.
• THIS PIPE MUST BE PLACED AT LEAST 300MM BELOW WATER LEVEL and can be
dressed with a push-in eyeball to match the project’s other wall ngs.
• The pipe is usually run along the sucon and return trench and elbowed up within the
equipment area. THIS PIPE MUST BE LEVEL TO AVOID AIR LOCKS which will aect
ow and performance.
• A 50mm cap is provided to cover the sensor pipe housing and protect the Sensor
from dust, debris, pests and foreign materials. The cap ts neatly onto the 50mm
sensor pipe housing.
• DO NOT GLUE THE CAP TO THE SENSOR HOUSING PIPE.
• If the Sensor is to be located away from the equipment area, ALWAYS RUN THE LEAD
THROUGH ADEQUATELY SIZED CONDUIT THAT WILL ENABLE THE COMPLETE
SENSOR TO BE REPLACED AT A LATER DATE.
• NEVER CUT EXCESS SENSOR CABLE. Roll excess cable and bind together with the
Velcro straps provided.
NOTE:Sensor and Solenoid
plugs must face backwards when
inserted into the new Water
Witch Control Box.
Product
Support Guide
waterwitch
Electronic Water Leveller
08
SOLENOID VALVE INSTALLATION
The Solenoid is regulated by the Control Box. When the water level is low the Control
Box sends a 24V AC current to open the Solenoid so water ows in to the project.
The Solenoid will close when the water level is restored to the correct level.
Solenoid cables up to 100m long are available by special order.
INSTALLATION PROCESS AND CONSIDERATIONS:
• Install Backow Prevenon Valve and Solenoid into water supply/ll line, ensuring arrows
are pointed in the direcon of the water ow. Connect Solenoid Cable to the Solenoid and
Control Box.
Balance line to be
300mm below water level
50mm balance line
POOL
Solenoid &
backflow
valve
Tap or
Two-way
valve
20mm
supply
line
20mm air gap
Water source
Control
Box
Balance line to extend
300mm above water level
NOTE
20mm air gap may not be required where
Ensure the Backow
Prevenon Valve and
Solenoid Valve direconal
ow arrows are pointed
in the same direcon as
the water ow.
OPTION 1
Solenoid installed into
balance line
Tabla de contenidos
Otros manuales de Sistema de agua de Cooke
Manuales populares de Sistema de agua de otras marcas
Spirotech
Spirotech SPIROVENT SUPERIOR S250 Manual de usuario
Culligan
Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manual de usuario
A.O. Smith
A.O. Smith Dura-Max AJH - 1000A - P Manual de usuario
Microline
Microline T.F.C.-4 Manual
Eureka Forbes
Eureka Forbes Aquaguard Select Manual de usuario
Cetetherm
Cetetherm AquaEfficiency Manual de usuario
