Convision CC-5201 Manual de usuario
Manual CC 5201 1
Manual
CC-5201
Date: January 2011 Convision Systems GmbH
Manual CC 5201 2
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than those specified.
Do NOT expose this appliance to rain or moisture.
This Installation should be made by a qualified service person and should confirm to all local codes.
Manual CC 5201 3
Warning
The camera requires periodic inspection.
Contact an authorised technician to carry out the inspection.
Stop using your camera when you find it malfunctioning.
If the camera emits smoke or is unusually hot for a long period, a fire may be caused.
Do not install the camera on a surface that can not support it.
If the camera is installed on an inappropriate surface, it may fall and cause injury.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not dis-assemble the camera.
It may result in an electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in a fire or other hazards.
Manual CC 5201 4
Contents
NOTICE 5
Important Safeguard 5
Precautions 5
Features 6
Components and Accessories 7
Overview 7
Front View 7
Dimensions 7
Side View 8
Bottom View 8
Rear View 9
Installation Procedure 10
Lens 10
Using an Auto Iris Lens 10
Using a C/CS mount Lens 11
Connecting to a Monitor 12
Connecting to Power 13
Control via the RS-485 Interface 14
Camera Operation 14
Menu 14
Switch 14
Main Menu 15
Exposure 15
White Balance 16
Day / Night 16
Motion 16
Privacy 17
Option 18
Display 19
Sync 19
Internal 19
Exit 19
Troubleshooting 20
Specifications 21
Manual CC 5201 5
NOTICE
Important Safeguard
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments / Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they
may cause hazards, damage product and void warranty.
4. Water and Moisture
Do not use this product near water or moisture.
5. Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly
installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only
with a mounting device recommended by the manufacturer, or sold with the product. To insure proper
mounting, follow the manufacturer's instructions and use only mounting accessories recommended by
manufacturer.
6. Power source
This product should be operated only from the type of power source indicated on the marking label.
Precautions
■Operating
-Before using, make sure power supply and others are properly connected.
-While operating, if any abnormal condition or malfunction is observed, stop using the camera
immediately and then contact your local dealer.
■Handling
-Do not disassemble or tamper with parts inside the camera.
-Do not drop or subject the camera to shock and vibration as this can damage camera.
-Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your
quality of camera.
■Installation and Storage
-Do not install the camera in areas of extreme temperature, which exceed the allowable range.
-Avoid installing in humid or dusty places.
-Avoid installing in places where radiation is present.
-Avoid installing in places where there are strong magnetic fields and electric signals.
-Avoid installing in places where the camera would be subject to strong vibrations.
-Never expose the camera to rain and water.
Manual CC 5201 6
Features
Ultra High Resolution
By adopting a 410,000 pixel Sony CCD, the
camera produces clear picture quality with
a horizontal resolution of 540 TV lines for
colour and 570 TV lines for B/W.
Fine Picture in Ultra Low Illumination
½ inch CCD allows bright and high quality
images to be captures in ultra low light
condition.
-Color: 0.08Lux / F1.2
-B/W: 0.01Lux / F1.2
-Sens up: 0.001Lux / F1.2
Filter Changeable Day & Night
This camera has a function that
automatically selects the mode that is
appropriate for daytime or night-time
conditions. The Color mode operates in
daytime conditions to provide optimum
colors, and BW mode operates in nighttime
conditions to enhance the definition of the
image.
Electronic IRIS
The electronic Iris function enables
continuous automatic control of the shutter
between 1/60(1/50)~1/120.000 sec.
Privacy Function
The Privacy function conceals the areas
you do not whish to appear on the screen.
DNR (Digital Noise Reduction)
The amount of low illuminance noise
has been significantly reduced, and the
signal-to-noise ratio (S/N ratio) as well as
horizontal resolution have been improved,
resulting in clear and sharp images
displayed even in the dark.
Controlled by OSD Menu
The camera can be controlled by selecting
text displayed on the monitor screen.
Additional Functions
Sens-up, Motion Detection, Mirror,
Sharpness and Sync (INT/AUTO) functions
are also available.
RS-485 Communication Control Support
Remote OSD menu control via an RS-485
interface is supported.
Manual CC 5201 7
Components and Accessories
1. Day & Night CCD Camera
2. Auto Iris Lens Connector Plug
3. C-Mount Adapter
4. Instruction Manual
Overview
Front View
1. Tripod Mounting Bracket Screw Hole
Used to fix Tripod Mounting Bracket to the top of the camera
2. C-Mount Lens Adapter
Install this adapter to use a C-Mount Lens
3. Back Focus Control Lever
Adjust Back Focus using this control lever
Dimensions
Manual CC 5201 8
Side View
4. Auto Iris Lens Connector
Used to connect Auto Iris Lens plug.
Bottom View
5. Tripod Mounting Bracket Screw Hole
Used to fix the camera onto a bracket or tripod.
The screw sizes for this hole are as follows:
The Tripod Mounting Bracket can be unscrewed and installed
on the top or bottom of the camera. Make sure to use the
Tripod Mounting Bracket when fixing the camera to a bracket
or tripod, otherwise the camera may be unstable and the
internal circuitry of the camera may get damaged.
Manual CC 5201 9
Rear View
6. OSD Setup Buttons
Set Button: Displays the menu on the screen. Press this button to confirm status or after
changing a selected item.
Up and Down Button: Used to move the cursor up and down in the menu screen to select a
desired menu item.
Left and Right Button: Used to move the cursor left or right in the menu screen or to change the
value of the selected item.
7. D & N Input Port/GDN: Color, Open: B/W)
Switch to Day or Night Mode by connecting an external signal to this port.
8. MD Output Port
Motion detection signal is output through this port.
9. RS-485 Control Port
The SETUP MENU can be controlled via this port using an external controller that supports RS-
485 communications.
10. Power LED
When power is properly connected, the LED illuminates.
11. Video OUT Port
Video signals are output through this port. Connect this port to the Video IN port of a
Monitor/DVR.
12. Auto Iris lens selection switch
Used to change between DC or Video depending upon the type of auto iris in use.
13. Power IN Port
Connections for Camera power, as specified for each model.
Manual CC 5201 10
Installation Procedure
Lens
The lens is not supplied with this camera. Purchase a lens suitable for the environment. This camera
accepts an auto iris lens and both C-and CS-mount lenses.
Note
It is recommended to use the DC type Auto Iris Lens to effectively enjoy the major functions of this
camera.
Keep the lens surface clean, as the picture quality suffers if there is dirt or fingerprints on the Lens.
Using an Auto Iris Lens
1. Strip 8mm of insulation from the end of the Auto Iris Lens cable.
2. Strip 2mm of insulation fro each of the cores of the cable.
3. Remove the cover of the Auto Iris Lens connector plug and solder the lens cable to the
connector pins of the plug.
For a Video Drive Lens For a DC Drive Lens
Pin 1: Red (Power) Pin 1: Damping –
Pin 2: NC Pin 2: Damping +
Pin 3: White (Video Signal) Pin3: Drive +
Pin 4: Black (Ground) Pin4: Drive –
Tabla de contenidos
