Controls MVP-A6235 Manual de usuario

Product Manual

Engine Control Module

Kubota Diesel Engines

Part Number: MVP-A6235

Revision: 2.0

Engine Type: Kubota Diesel with DPF Emissions Control

______________________________________________________________________________________________________________________________________

P.O. Box 368 • Sharon Center, OH 44274

Phone 330.239.4345 • Fax 330.239.2845 • www.controlsinc.com

CONTROLS, INCORPORATED

C O N T R O L S Y S T E M S & S O L U T I O N S

- 1 -

TABLE OF CONTENTS

INSTALLATION INFORMATION……...........………………………………...……………………………………………………………....2

CONNECTOR INFORMATION……...........………………………………...………………..………………………………………………….3

MENU NAVIGATION………………………………………………………………..……………………………………………..…………….…......5

MENU SYSTEM…………………………………………………………………...…………………………………………………..……………….…......6

OPERATOR MENU…………………………………………………………………..…………………………………………………..………….…......8

EMISSIONS PARAMETERS

ACTIVE FAULT CODES

STORED FAULT CODES

OPERATION EVENT LOG

ALARM EVENT LOG

ENGINE PARAMETERS

ENGINE IDENTIFICATION

MODULE INFORMATION

CONTROLER SETUP MENU……………………………………………………………………………………………….….…………...……..11

QUICK SETUP

PARAMETER CONFIGURATION

INPUT CONFIGURATION

THROTTLE CONFIGURATION

ENGINE SAFETY CONFIGURATION

MODULE CONFIGURATION

DISPLAY CONFIGURATION

MAINTENANCE CONFIGURATION

PANEL ENGINE SAFETY PROTECTION …………………………………….……………………………………......……..……..…17

PRE ALARMS AND ALARMS

SAFETY SHUTDOWNS

INDICATOR LAMPS

EMISSIONS MONITORING - REGENERATION……………………….……………………………………....……....……..…18

REGEN LEVELS

REGEN BUTTONS

PARKED REGENERATION PROCESS

REGEN STATUS

REGEN FAIL/ABORT

CONTROLS, INCORPORATED

C O N T R O L S Y S T E M S & S O L U T I O N S

- 2 -

INSTALLATION INFORMATION

CONTROLS, INCORPORATED

C O N T R O L S Y S T E M S & S O L U T I O N S

- 3 -

CONNECTOR INFORMATION

BATTERY +

CAN HIGH

CAN LOW

DIGITAL INPUT 1

FUEL LEVEL

BATTERY -

5VDC SUPPLY

NEUTRAL SWITCH

THROTTLE DOWN

THROTTLE UP

PARKING BRAKE SW

GROUND (B-)

Part# 3FK-108

Connector A Kit

(1) Deutsch DT06-6S plug

with (6) 0462-209-10614 sockets

CONTROLS, INCORPORATED

C O N T R O L S Y S T E M S & S O L U T I O N S

- 4 -

PANEL CONNECTOR

Engine Harness Connector –Deutsch 21 pin (HDP24-24-21PE)

21 Pin Connector

Function

Battery Positive

Battery Negative

Key On Power

Crank Signal

J1939 High

J1939 Low

Alternator Excite

Neutral Switch Input

Parking Switch Input

Engine Harness

Connector (21 Pin)

CONTROLS, INCORPORATED

C O N T R O L S Y S T E M S & S O L U T I O N S

- 5 -

MENU NAVIGATION

To access the control module menu system, power the unit and press the Menu button. While

pressing the menu button a message will appear to also press Enter to access.

Once you have accessed the menu system, the four key pad will be used for menu navigation and

therefore not available for engine speed control if the engine is running. The menu system is broken

into two main sections, the operator menu and the controller setup menu. The operator menu

contains information about the engine and control panel. The topics will vary based on the engine

type and control panel model. Pressing the Menu key will index the menu topic to the next item in

the list. The index is circular so you will eventually wrap around to the beginning of the operator

menu structure. Pressing the Enter key will index the topics backward. Once you have arrived at a

menu topic that you would like to explore more, press the Up arrow key. The Up arrow key will

index the screen each time it is pressed. Pressing the Down arrow key will index in the reverse order.

Pressing the Menu key at any time while in a topic will return you to the main menu topic heading.

To exit the menu, simply press the Menu and Enter keys simultaneously.

MENU SYSTEM

CONTROLS, INCORPORATED

C O N T R O L S Y S T E M S & S O L U T I O N S

- 6 -

OPERATOR MENU

First Menu

Operator

Controller

Setup

CONTROLS, INCORPORATED

C O N T R O L S Y S T E M S & S O L U T I O N S

- 7 -

Emissions Parameters

This menu allows for the viewing of the engine emissions data as broadcast by the ECU by pressing

the up arrow button. This data includes:

DOC Inlet Temperature

DPF Soot Load

DPF Inlet Temperature

Time at Last Regeneration

DPF Outlet Temperature

Active Regen Status

Regen Options

Regen Inhibit Status

DPF Differential Pressure

Active Fault Codes

This menu allows for the viewing of any Active Fault Codes as broadcast by the engine ECU by

pressing the up arrow button.

Stored Fault Codes

This menu allows for the viewing of any Stored Fault Codes as broadcast by the engine ECU by

pressing the up arrow button.

Operation Event Log

The operation log will record the engine start and stop events and tag them with the engine run

time hours. The Alarm can be viewed in the Operator menu area and can be cleared in the Module

Configuration section of the Controller Setup menu.

Alarm Event Log

Any monitored pre alarm or alarm will be recorded in the Operator menu section. The event will be

tagged with the actual engine run time hours at which the event occurred. The log stores the last 32

events and can be cleared in the Module Configuration section on the Controller Setup menu.

Engine Parameters

This menu allows for the viewing of unique engine information broadcast by the ECU by pressing

the up arrow buttons. This information includes:

Total Hours

Engine Torque

Requested TSC

Coolant Temperature

Rated Speed

Fuel Rate

Low Idle Speed

Manifold Temperature

Load at RPM

Potential Voltage

Engine Identification

CONTROLS, INCORPORATED

C O N T R O L S Y S T E M S & S O L U T I O N S

- 8 -

This menu allows for the viewing on the engine model number and serial number.

Module Information

This menu allows for the viewing of the Module Part number and Software Version.

Controller Setup

When navigating through the Operator menu, you will arrive at the Controller Setup screen. To

configure the module to new settings, you can enter into this area by pressing the Up arrow key.

The next screen will ask for a password. If no password, or an incorrect password is used, navigation

into the menu is still possible and permitted, however, the ability to make changes will be restricted.

To enter the password, press the Enter key and brackets will appear. Use the Up and Down arrow

keys to set each digit individually, pressing the Enter key to index to the next digit from left to right.

Once the last digit is entered, the brackets will disappear and the digits will be represented with

asterisks. Pressing the Up arrow will index you to the Quick Setup menu and programming can

continue.

CONTROLS, INCORPORATED

C O N T R O L S Y S T E M S & S O L U T I O N S

- 9 -

Navigating the Controller Setup menu structure is done in the same manner as the Operator menu

system. Menu will index to the next topic, The Up arrow will access the topic, etc. To make changes

to the settings, you will need to locate the item you are looking to modify under the appropriate

topic and then press the Enter key and the editing brackets will appear allowing you to make

changes to the value or change the selection. Once you have made your selection or changed the

value, simply press Enter again to accept it and the editing brackets will be removed.

CONTROLLER SETUP MENUS

QUICK SETUP

The Quick Setup menu is available to allow a user to quickly set up the basic configuration of the

control panel to match the engine. Selections in the Quick Setup will propagate into other areas of

Tabla de contenidos

Otros manuales de Unidad de control de Controls

Controls

Controls XL-500E-AS Manual de usuario

Controls

Controls J1939 Manual de usuario

Controls

Controls MVP-G342 Manual de usuario

Controls

Controls MVP-62303 Manual de usuario

Controls

Controls CX Series Manual de usuario

Controls

Controls MVP-A3238 Manual de usuario

Controls

Controls MVP-A3235 Manual de usuario

Controls

Controls MVP-M702 Manual de usuario

Controls

Controls G3-1015 Manual de usuario

Controls

Controls MX Series Manual de usuario

Controls

Controls XCAN-AC Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario