Contex HD Ultra X Series Guía

June 2018

OTAC Replacement Work Instruction

Tools required:

T10 screwdriver

Pliers

T20 screwdriver

E-clip Tool (size 5)

Small Flat Screwdriver

Prerequisite

Disconnect power from the scanner.

Removing the OTAC Unit

1. Open the OTAC Assembly by

depressing the Lid Latches at

both ends.

2. Use a cloth (or similar) to cover

the gap in the lower chassis, to

prevent the e-clip from falling into

the chassis, then remove the E-

clip using small flat screwdriver.

3. Repeat for the right end, again

making sure to use a cloth to

prevent the e-clip falling into the

chassis.

4. Slide a piece of paper under the

Guide Plate Hinge, to prevent

the T20 screw falling into the

chassis while removing it from

the side plate.

HD Ultra X Series Instructions 2

5. Repeat for the other end of the

Guide Plate.

6. Lift the OTAC and remove the

brass spacers at both ends.

7. Carefully push the Gas Piston off

from the bracket, making sure

not to cause any damage.

8. Repeat for the other end of the

Guide Plate.

HD Ultra X Series Instructions 3

9. Carefully lift the whole OTAC

Unit, including the Top Lid Cover

off from the chassis

Replacing the OTAC Unit

1. When replacing the Guide Plate,

make sure the Gas Pistons go

inside of the end plates

2. Position the Gas Piston over the

pillars on the end plates at both

ends.

3. Lift the OTAC and refit the brass

spacers at both ends.

HD Ultra X Series Instructions 4

4. While pressing down on the

Guide Plate, to align the screw

holes, and using paper to cover

the gap to prevent the screw

falling into the chassis, refit the

long T20 screw. Do this at both

ends of the Guide Plate.

5. Use an e-clip insertion tool, (or

pliers) to refit the e-clips over the

Gas Piston bracket. Make sure it

is fully clicked in place. Repeat at

both ends.

6. To refit the Lid Cover, with the

OTAC at its highest level,

position the Lid Cover back on

the Guide Plate.

7. Making sure the locating pins go

into slots on the OTAC at both

ends.

HD Ultra X Series Instructions 5

8. Retighten the 3 x T10 locking

screws to hold the Lid Cover

down and in place.

9. Press down on the Guide Plate

until both ends lock in place to

close.

10. With the scanner powered up,

and the OTAC pushed down,

with the added +1 click on the

ratchet, make sure the LED for

the raised lid is off.

11. If the LED does NOT go out

when the OTAC is closed, then

remove the rear panel to access

the sensor, to make adjustments.

Remove the T10 screws and lift

the rear panel off from the back

of the scanner.

HD Ultra X Series Instructions 6

12. Insert a T10 screwdriver into the

access hole in the back of the

scanner, loosen the locking

screw, and move the sensor

bracket up or down until the Lid

LED goes out.

13. Retighten the screw.

14. Retest the LED but raising the

OTAC, and pressing down,

adding the +1 ratchet click. If the

LED is correctly setup (still off),

then refit the rear cover.

Video Work Instruction: http://www.training.contex.com/OTAC

Tabla de contenidos

Otros manuales de Escáner de Contex

Contex

Contex SD One MF 44 Manual de usuario

Contex

Contex AB51A Manual

Contex

Contex SD 3600 series Manual de usuario

Contex

Contex IQ FLEX Manual de usuario

Contex

Contex XD2490 Manual de usuario

Contex

Contex IQ Quattro X Series Manual de usuario

Contex

Contex AA51A Manual

Contex

Contex HD iFLEX Manual de usuario

Contex

Contex SD One 36 Manual de usuario

Contex

Contex SD One MF Instrucciones de montaje

Contex

Contex IQ 2400 Series Cómo utilizar

Contex

Contex SD One+ Cómo utilizar

Contex

Contex FSS4300 Manual

Contex

Contex SD One+ Manual de usuario

Contex

Contex IQ FLEX Cómo utilizar

Contex

Contex HD Ultra X 6000 Series Manual de usuario

Contex

Contex HD Ultra X 6000 Series Cómo utilizar

Contex

Contex Wide Format Color Manual

Contex

Contex FLEX50i Manual de usuario

Contex

Contex GX67D Manual

Contex

Contex Chroma 8040 Manual

Contex

Contex GX67D Manual

Contex

Contex HD Ultra Series Manual de usuario

Contex

Contex IQ 4400 Series Manual de usuario

Manuales populares de Escáner de otras marcas

Plustek

Plustek Scanner Manual de usuario

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manual de usuario

Renkforce

Renkforce DS100-5M Manual de usuario

Image Access

Image Access WideTEK A2 Manual de usuario

Canon

Canon imageFORMULA CR-120N Manual de usuario

Fujitsu

Fujitsu FI-4860C2 Manual de usuario

GeoSlam

GeoSlam ZEB Horizon Instrucciones de instalación

Kodak

Kodak i5800 Scanner Manual de usuario

Kodak

Kodak i7300 Manual de usuario

Revopoint

Revopoint POP Manual de usuario

Fujitsu

Fujitsu fi-4860C Manual de usuario

Eddyfi Technologies

Eddyfi Technologies Floormap X Manual de usuario

Faselase

Faselase F6 Manual de usuario

Fujitsu

Fujitsu CardMinder Manual de usuario

Uniden

Uniden BC340CRS Manual de usuario

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manual de usuario

Mustek

Mustek PageExpress 4800 Pro Manual de usuario

Optex

Optex 750830 Manual de usuario