Connevans Sonumaxx 2.4 Manual de usuario
14 English
Scope of delivery
1 Underchin- or pocket receiver
2 Transmitter
3 Polymer Lithium Rechargeable Battery
x 2 pieces
4 AC/DC Adapter
5 RCA Adapter Cable
6 Audio Cable (both ends with 3,5
mm stereo plug)
7 6,3 mm to 3,5 mm Adapter Plug
8 External Microphone
9
TOSlink cable
10 neck loop
- Warranty card (not depicted)
sonumaxx24+PR_0917.indd 14 18.10.2017 09:09:04
English 15
Controls: Receiver
1 Adjustable Earbuds
2 3,5 mm earphone jack (pocket recei-
ver only)
3 Volume Control
4 LED Indicator of Power/Signal
5
MIC Button for verbal communication
6 Power On/Off Switch
7 Microphone
8
Sound Balance Control (Left/Middle/Right)
9 Battery
10 Belt Clamp (pocket receiver only)
Front:
Pocket receiver Underchin receiver
Back:
Underchin receiver Pocket receiver
sonumaxx24+PR_0917.indd 15 18.10.2017 09:09:04
16 English
Controls: Transmitter
1. Charging Cradle
2. LED Indicator of Tone Clarity
3. Tone adjustment button
4. LED Indicator of Power/Signal
5.
LED Charging Indicator for Main Battery
(attached to Headset Receiver)
6.
LED Charging Indicator for Spare Battery
7. Spare Charging Slot
8. DC In
9. 3.5mm Audio In Socket
10. Audio / Optical input selector switch
11. optical input digital
Back
Front
Introduction
This 2.4GHz digital wireless chin headset uses the latest technology in digital wireless
transmission and offers sound amplification.
Simply connect the transmitter to a desired audio source: DVD player, CD player, TV set,
Hi-Fi system or MP3-Player. Without complicated wiring and installation, the system enables
you to enjoy thrilling, lifelike sound within minutes.
sonumaxx24+PR_0917.indd 16 18.10.2017 09:09:04
English 17
Features
- 2.4GHz Digital Hopping System Technology
- Charging bay
- Automatic shutoff, if no audio comes in
- Communication function
- Fast recharge
- Easy-to-change spare battery
- External microphone for environmental audio pickup.
- Sound balance adjustment
- Tone adjustment
Installation: Transmitter
1.
Connect the power adapter to the DC IN input socket located on the transmitter rear panel.
2. Connect the power adapter provided to an electrical outlet.
3. RCA adapter cable, audio cable, 6.3 mm to 3.5 mm adapter plug, Toslink cable and
the external microphone serve to connect the transmitter to a sound source of your
choice (for example DVD- or CD player, TV-set, stereo set or MP3-player).
4. Shift the input selector switch towards the accordingly connected input.
3,5 mm Headphone
Socket
6,3 mm Headphone
Socket
RCA-Socket
Microphone,
for acoustic
pickup
sonumaxx24+PR_0917.indd 17 18.10.2017 09:09:04
18 English
sonumaxx24+PR_0917.indd 18 18.10.2017 09:09:05
The green power indicator LED will blink as soon as you have connected the power adapter
to the electrical outlet, when the audio signal is detected from the audio source, and the
green LED indicator will glow constantly.
Receiver
Insert a battery into the receiver with correct polarity.
Ilustration example: Underchin receiver
Operation
1. Move the ON/OFF switch on the receiver to the OFF position.
2. Place the receiver in the charging bay of the transmitter, make sure that the contacts of
receiver and transmitter touch each other.
3. The charging process starts automatically. The indicator LED for the main battery glows
red. It will change to green after about 2 hours when the battery is fully charged.
4. A spare battery is provided for extended use. Simply insert it into the transmitter for
charging. The indicator LED for the spare battery will change from red to green when the
battery is fully charged.
The pocket receiver features a 3.5 mm audio socket, which is located on top of the device
and enables the connection of the neck loop or any other regular headphones (not inclu-
ded).
Note:
Make sure that the batteries included in this set are fully charged before using them for the
first time. Charge the battery for about 3 hours before first use.
RF transmission of the transmitter will automatically switch OFF in approximately 5 minutes
if there is no audio signal, or the signal that it receives from the audio source is too weak for
proper reception. However, if the signal returns to an acceptable level, the transmitter will
automatically switch ON again.
English 19
sonumaxx24+PR_0917.indd 19 18.10.2017 09:09:05
Charging the batteries
1. Select the On/Off Switch in the headset receiver to OFF
position.
2. Place the headset receiver on the transmitter, make
sure the charge contact touches the charge pins on the
Transmitter.
3. The charging process starts automatically. LED indicator
of main battery then glows in red constantly. It will glow
in green about 2 hours after the battery is fully charged.
4. A spare battery is provided for sustained enjoyment.
Simply insert it into the transmitter for charging.
LED indicator of spare battery will then glow in red constantly.
It will glow in green about 2 hours after it is fully charged.
Warning:
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such
as sunshine, fire or the like. Never use another type of battery or non-rechargeable batteries
to replace the rechargeable batteries supplied. When the headphones are not in use, move
the switch to the OFF position to avoid damaging the batteries.
The batteries must always be fully charged before first use. An initial 3 hours charge is
required to guarantee an acceptable service life for the rechargeable batteries. Always en-
sure that the headset receiver is switched to OFF position while the batteries are charging.
Excessive sound pressure from earphones and headphones can cause hearing loss.
Important:
This unit should be operated with the special rechargeable batteries only. When replacing
the batteries or when disposing of the unit, always comply with applicable laws relating to
the disposal of batteries. Please place them in a proper disposal container to ensure that
they are eliminated safely and in an environmentally friendly way.
Ilustration example: Underchin receiver
20 English
sonumaxx24+PR_0917.indd 20 18.10.2017 09:09:05
Tone clarity:
Tone adjustment
If required, the tone of the receiver can be adjusted. Press the Tone adjustment button to
match your preference. The current setting is visible by the orange 1, 2 and 3 LEDs.
The tone / speech intelligibility can be enhanced individually on the transmitter with the
following settings:
Communication feature:
The sound of the transmission can be interrupted at any time, for example to talk to a person
in the same room. Press the MIC-button of the receiver once. The receiver‘s inbuilt micro-
phone will now register the surrounding sounds and amplifies them. The volume can be
adjusted with the volume control. To end this function, press the MIC-button once more - the
previous transmission will now continue.
English 21
sonumaxx24+PR_0917.indd 21 18.10.2017 09:09:05
Troubleshooting:
No sound:
- Ensure that the mains adapter is pushed fully into the power outlet and that its cable is
properly connected to the DC IN connector on the transmitter.
- The charge level of the headset receiver battery may be too low. Recharge the battery
or replace it with a fully charged battery.
- Ensure that the TV set, Hi-Fi system or audio component is switched ON and set to a
channel that broadcasts an audio signal.
- Use the volume control on the Headset Receiver to increase the sound level.
- The connected audio/video equipment may not be in playback mode. Start playback on
by the equipment.
- The Headset Receiver output level is set too low. Adjust the volume to a suitable level.
Pocket receiver only: Make sure that the plug of the neck loop is correctly inserted.
Distortion:
- The charge level of the headset receiver battery may be too low. Recharge the battery
or replace it with a fully charged battery.
- The headset receiver may be too far away from the transmitter. Move closer to it.
- The audio signal input level is too low. Increase the volume from the audio source.
In case the receiver cannot be linked with the transmitter, please follow the following pro-
cedure for pairing :
1. Disconnect the transmitter from the power supply.
2. Turn ON the headset receiver.
3. Hold the MIC-button pressed for approx. 5 seconds, the green LED on the receiver will
start to blink rapidly. Immediately reconnect the power supply to the transmitter.
4. The receiver and the transmitter are hereby paired automatically, the steadily lit green
LED on the receiver indicates successful pairing.
22 English
sonumaxx24+PR_0917.indd 22 18.10.2017 09:09:05
Tabla de contenidos
Otros manuales de Receptor de Connevans
