Condair Nortec GSTC Manual de usuario
LINKS XPS
Nortec GSTC / SETC
B+ Models
Installation and
Operation Manual
Includes installation, operation
maintenance and troubleshooting
information for your GSTC / Nortec
SETC B+ Links XPS Options.
2559109-H | 30/11/2018
Important: Read and save these instructions. This guide to be left with equipment.
Thank you for choosing Condair
Proprietary Notice
This document and the information disclosed herein are proprietary data of Condair Ltd. Neither this document
nor the information contained herein shall be reproduced used, or disclosed to others without the written
authorization of Condair Ltd., except to the extent required for installation or maintenance of recipient’s
equipment.
Liability Notice
Condair does not accept any liability for installations of humidity equipment installed by unqualified personnel
or the use of parts/components/equipment that are not authorized or approved by Condair.
Copyright Notice
Copyright 2018, Condair Ltd. All rights reserved.
INSTALLATION DATE (MM/DD/YYYY)
MODEL #
SERIAL #
Contents
1Overview
1Multi-Unit Systems
2BACnet, LonWorks, and N2 Modules
3Wiring the Links XPS Module
6 Configuring the Humidifiers
8 Wiring
8 BACnet MS / TP, Johnson N2, and LonWorks
9 BACnet / IP
10 Gateway Configuration
10 Changing Unit Device Instance and BACnet MAC Address
13 Changing Baud Rate (BACnet MSTP, Johnson N2 LonWorks)
23 Changing the IP Address (BACnet IP)
28 Network Integration
28 LonWorks.xif file
28 Retrieving XIF File Instructions
30 BACnet Pics and Bibs
30 Variable Definition
43 Startup Checklist
44 Troubleshooting
44 Indicator Lights
Links XPS for Nortec GSTC/ SETC B+ |1
Overview
The GS/SE Links XPS Option allows for the integration of a Nortec GSTC/ SETC Series humidifier
within a BACnet, Johnson N2 or LonWorks network. This option features a gateway that has the
capability of converting information from the host Modbus protocol to a specified secondary
protocol.
The following protocol options are available, and must be specified at time of order:
Table 1: Protocol Options
Protocol
BACnet MS/TP
BACnet / IP
Johnson N2
LonWorks
Multi-Unit Systems (“Master/Slave”)
Up to 8 humidifiers can be chained and monitored through a single Links XPS package. In this
configuration, the unit with the Links XPS package is designated the “Master Unit”, while the
remaining 7 humidifiers are configured as “Slaves”. The master unit is connected to the
Building Management Systems (BMS). Each unit is separately addressed, it is possible to
monitor and control each unit individually.
Different networking configurations may be achieved depending on the type of network being
used. One networking example could have a Gateway installed inside the lead unit, which could
then be daisy-chained to successive units. In turn, the lead unit would connect to a Building
Management System (BMS) network via a shielded, twisted-pair connection. Please see wiring
section for additional detail. A second example could have a series of units directly connected
to an Ethernet network. This is only possible for BACnet communication and is essentially
referred to as a BACnet/IP configuration.
2 |Links XPS Nortec GSTC/ SETC B+
Field Installation or Retrofit Instructions
BACnet, LonWorks and N2 Modules:
Caution: Disconnect power before performing work inside cabinet.
Remove the Humidifiers front access panel. Install the bracket assembly using 8-32x ½” hex-
drive screws. Notice, 4 screws are used for the hinges, and the 5th screw for fastening the
bracket in place.
Figure 1: Nortec GSTC/ SETC with Links XPS Installed
Links XPS for Nortec GSTC/ SETC B+ |3
Figure 2: Detail of Hinge
Wiring the Links XPS Module
Most of the wiring connections for the new Links XPS module will have already been finished at
the factory, however, there are a few connections that will need to be made to connect the unit
the Nortec GSTC/ SETC series humidifier. Refer the LINKS XPS wiring diagram included in the
package for details.
Module Power Connections: There will be a wire harness provided that will consist of a red and
blue wire. Both red and blue wires are terminated with a ring terminal.
Figure 3: Wires from Links XPS Bracket
4 |Links XPS Nortec GSTC/ SETC B+
a. The ring terminal of the red wire is to be connected to the power terminal on the 24V
side of the transformer located at the bottom, left of the electrical compartment.
b. The ring terminal of the blue wire is to be connected to the ground terminal on the 24V
side of the transformer.
Links XPS for Nortec GSTC/ SETC B+ |5
Humidifier Communication Connection: On the Links XPS assembly there will be a CAT5 cable
with RJ45 connector.
This connector is to be plugged into the jack on the bottom right side of the humidifier main PCB
processor board (Keypad chip).
Figure 4: Backside View of Humidifier PCB Board
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Humidificador de Condair
Condair
Condair Nortec GS II Series Manual de usuario
Condair
Condair AT Series Manual de usuario
Condair
Condair ABS3 Manual de usuario
Condair
Condair HumiLife RE Series Manual de usuario
Condair
Condair RM Series Manual de usuario
Condair
Condair EL Manual de usuario
Condair
Condair GS II Series Manual de usuario
Condair
Condair RM Series Manual de usuario
Condair
Condair Nortec GS Series Manual de instrucciones
Condair
Condair Nortec AIRFOG Series Manual de usuario
Condair
Condair HP Manual de usuario
Condair
Condair RH Series Manual de usuario
Condair
Condair HumiLife RH Series Manual de usuario
Condair
Condair Mk5 Manual de usuario
Condair
Condair EL Manual de usuario
Condair
Condair SOFT 10 Manual de usuario
Condair
Condair GS series Manual de usuario
Condair
Condair Nortec EL005 Manual de instrucciones
Condair
Condair GS C Series Guía
Condair
Condair RS series Manual de usuario
