Concox GT02N Manual de usuario

GPS Vehicle tracker

(GPS+GSM+SMS/GPRS)

GT02N User Manual

(Version 2.1)

Thank you for purchasing the tracker. This manual shows how to operate

the device smoothly and correctly. Please make sure to read this manual

carefully before using this product. Please note that specification and

information are subject to changes without prior notice in this manual.

Any change will be integrated in the latest release. The manufacturer

assumes no responsibility for any errors or omissions in this document.

1. Summary

Working Based on existing GSM/GPRS network and GPS

satellites, this product can locate and monitor any

remote targets by SMS or internet.

Overview of the characteristics:

1.GSM 850/900/1800/1900MHZ.

2.GPS position.

3.Auto set APN.

4.180Mah Battery inside, Power-Cut alarm.

5.Motion detect, save GPRS flow and power.

6.GEO-fence Alarm.

7.SOS Alarm.

8.Vibration Alarm.

9.ACC Alarm.

10.Speed Alarm

11.Voice Surveillance.

12.Voltage Range: DC 10V-40V.

13.Enginee Cut off.

2．Accessories：

Power line: Relay: Microphone:

SOS line: Manual

3. Specs

1）.GSM：850/900/1800/1900MHZ

2）.GPRS: Class12, TCP/IP

3）.Working Voltage：10V-40V DC

4）.Working current：≈22mA (12VDC)

5）.Working current：≈12mA (24VDC)

6）.GPS locating time：Cold start≈38s（Open sky）

Warm start≈32s

Hot start≈2s（Open sky）

7）.GPS Precision：10m（2D RM）

8）.Working temperature：-20℃～+70℃

9）.Working humidity：20%～80%RH

10）.Measurement：97（L）×50（W）×15（H）mm

4. Wire defined

The 2pins orange plug connect with SOS line

The 2pins blue and green plug connect with microphone.

The 4pins plug connect with power line.

For 4pins power line:

The red wire connect with power DC12V+

The black wire connect with power DC12V-

The white wire from tracker connect with yellow line from

relay,the white line from relay connect with power DC12V+.

Then cut the power + wire of pump to 2 sides.

Every side connect with relay green line.

5.Device status indicators

5.1 Connect DC 10-40V power supply, push the switch (switch beside

the SIM card holder), the red LED will light continuously.

5.2 The blue LED light continuously when searching the GPS signal.

Once GPS fixed, the blue LED will be flashing.

5.3 The intermediate green LED (GSM signal state) GSM signal is

normal, green LED flashing. No GSM signal, the green LED light

continuously.

6.Installation

6.1 Prepare for installation

6.11 Product Check. Open the packing box and check the device’s model

and accessories. If the model is wrong or the accessories not

complete, please contact the dealer.

6.12 Choose SIM card. Please insert a SIM card which support GSM 2G

network to the device. Please take dealer’s advice as reference.

6.13 SIM card installation. Discharge the cover of the device and uncover

the SIM card holder. Then insert the SIM card and cover SIM card

holder (as follows).

6.14 Open the cover, Push the switch. Then Put back the front cover.

6.15 Connect the device to the 10V-40V power supply.

6.16 Install the device in the hidden place of the car；

The SIM card must be with GPRS function and enough deposit. If your

SIM card need input PIN when power on, please cancel it.

6.2 Installation

The GPS tracker must be installed under professional

personnel.

Note：

1) Please install the device in the hidden place as

followings：

2) Avoid being placed with signal radiators like reverse

sensor ；

3) The device has GSM antenna and GPS antenna inside. Please

ensure the receiving side of the device is face up and

without metal cover.

Note: The metal cover will lessen the receiving of GPS

signals.

7. Device wiring requirements

7.1 The device power supply is DC 10V-40V. The red line is

positive pole while the black line is negative pole.

7.2 The negative pole of power supply connects with ground or

the metals. Please do not connect with other ground lines.

7.3 When finishing the power supply wire connection, please

make the plug of power supply to the device, the switch beside

sim card holder.

8.The Device Working

8.1 Power on:Connecting to the power. Then the three LED indicators will

light. The device will upload the data to the online platform

(the default interval of uploading data is 15seconds). When the

car is in static state for a long time, the device will be in

energy saving mode.

8.2 Power off：Pull off the power plug then power off the device.

9.User Settings

9.1 SMS Commands instruction

1)Center Number

Text

command

Parameter

Sample

CENTER Add

710#number#

711#number#

710#13500135000#

711#13800138000#

CENTER Del

D01#

D02#

Command

Description

1)Center number can control the oil and

power and resume factory settings

2) Center number can receive the call and

text of vibration alarm and over speeding

alarm.

3) SIM must display the income call number

to control oil and power.

4) Only 2 number can be center number.

5) Change center number must resend the

command.

Command

Feedback

Successful Setting：Add admin account 1 OK!

2) View Center Number

Text

command

Parameter

Sample

View

901#

Command

Description

This directive is used to view Device

Manager number.

Command

Successful Setting：Admin1:

Feedback

Admin2:

3)Authorized Number Set

Text

command

Parameter

Sample

Authorized

Add

101# number #

102# number #

103# number #

1：101#13800138000#

2：102#12345678912#

3：103#12345678912#

Authorized

Del

D11#

D12#

D13#

D11#

D12#

D13#

Command

Description

1) Authorization number for SMS control

oil.

2) Only three numbers to set the

authorization number

3) Change the authorization number needs

to delete the previous number

Command

Feedback

Successful Setting：Add Authorization

account 1 OK!

4) View Authorized Number

Text

command

Parameter

Sample

View

authorized

C10#

Command

Description

This directive is used to view the

equipment authorization number

Command

Feedback

Successful Setting：

Authorization 1：

Authorization 2：

Authorization 3：

5)APN Setting

Text

command

Parameter

Sample

APN Setting

802#APN#username#passw

ord#

1：802#intenet#123#123#

2: 802#internet#

Command

Description

APN differs according to the local telecom

operators.

For example：APN request password，please refer to

Sample 1，and Sample 2 for no password.

Command

Successful Setting：SET APN OK！

Otros manuales de GPS de Concox

Concox

Concox Smart OBD Manual de usuario

Concox

Concox GT03C Manual de usuario

Concox

Concox GT300 Manual de usuario

Concox

Concox GPS Vehicle tracker Manual de usuario

Concox

Concox QBIT M Manual de usuario

Concox

Concox GPS Electric Cars Positioning Terminal Manual de usuario

Concox

Concox smartracker GT350 Manual de usuario

Concox

Concox GK310 Manual de usuario

Concox

Concox GT03A Manual de usuario

Concox

Concox Vechile Series Manual de usuario

Concox

Concox GT06F Manual de usuario

Concox

Concox GT06N Manual de usuario

Concox

Concox GT06N Manual de usuario

Manuales populares de GPS de otras marcas

Raven

Raven Cruizer II Manual

Hama

Hama 53118 Manual de usuario

Garmin

Garmin SOUNDER 125 Manual de usuario

Garmin

Garmin DEZL 580 Manual de usuario

Jigabot

Jigabot EX Manual de usuario

Pointer

Pointer Cellocator CelloTrack XT LTE Guía de instalación

Queclink

Queclink GV55LITE Manual de usuario

Voxson

Voxson Voxtrack GPS500 Manual de instrucciones

Garmin

Garmin ECHOMAP PLUS Manual de usuario

Starcom Systems

Starcom Systems Kylos Compact Manual de usuario

Garmin

Garmin 15 H Series Manual de usuario

Cobra

Cobra Marine MC 600Ci Manual de usuario

Cellocator

Cellocator CelloTrack T Manual de usuario

Enfora

Enfora Mini-MT GSM2228UG001 Manual de usuario

Magellan

Magellan eXplorist 100 Manual de usuario

LTE

LTE G50B Manual de usuario

Garmin

Garmin DEZL OTR500 Manual de usuario

SkyGolf

SkyGolf SkyCaddie SG1 Manual de usuario