Comtrend Corporation CT-5611T Manual de usuario
DSL Setup Guide
Rev. April 17, 2009
Comtrend CT-5611T
For Technical Support, Call
877-450-3500 (Toll Free)
or
906-639-3500 (Local)
Providing Exceptional DSL, Dial-Up,
and Long Distance Services
397 US 41 N – P.O. Box 86
Carney, MI 49812-0086
906.639.3500 (Local)
877.450.3500 (Toll Free)
A Subsidiary of Upper Peninsula Telephone Company
2
DSL odem Installation Instructions
1. Install DSL filters on all active phone jacks.
DSL Filters
Standard Filter Wall ount Filter
Figure 1: DSL Filter for Standard and Wall ounted Phone Jacks
a. This includes fax machines, satellite dishes, alarm systems, and telephones.
NOTE: You UST obtain filters for all alarm systems from the alarm system
manufacturer.
Satellite dishes MUST be filtered
.
b. The filter UST be placed at the jack, NOT at the equipment.
2. To install the DSL filters on a standard jack:
a. Unplug the phone line from the jack.
b. Plug the phone line into the filter.
c. Plug the filter into the wall jack.
3. To install the DSL filters on a wall mounted jack:
a. Remove the existing wall telephone from the jack.
b. Insert filter into wall jack.
3
c. ount the filter over the wall jack lugs and slide down to attach.
d. Fully insert the telephone into the filter jack.
e. ount the telephone over the filter lugs and slide down to attach.
Connecting the Comtrend CT 5611-T to Computer
Figure 2: Rear of Comtrend 5611-CT odem Reset
4. Connect the Yellow Ethernet (LAN 10/100 ) cable to the back of the
modem.
5. Connect the power cable to the back of the modem and to the power outlet
or surge protector.
6. Verify that the modem Power button is in the On position.
7. Connect the telephone line to the DSL port on the modem.
a. You should use the telephone line that was previously attached to your
computer for dial-up Internet service, if available.
b. The phone line should run directly from the wall jack to the back of the
modem. There should be no splitters or filters (except for the splitter filter
provided), surge protectors, fax machines or any other equipment on that
line.
c. DO NOT place a filter (other then splitter filter provided) on the jack where
the DSL modem will be connected.
8. Verify that the proper lights are lit on the front of the modem.
a. The power light should be lit and solid.
b. The ADSL Link light should be lit and solid.
c. The LAN Link light should be lit and solid.
d. The Internet light should be lit and solid but may blink rapidly when surfing
the Internet.
4
9. ***Try surfing the Internet. ***
A. If you can surf the Internet, the installation is complete. Continue to Email
Setup.
If you cannot surf the Internet continue to the Configure the PC section.
Configure the PC
1. The next step is to disable any proxy settings in the Control Panel screen.
a. Windows Vista users should click on Start, then choose Control Panel.
b. Click Classic view if not already selected.
2. In the Control Panel, double click on Internet Options.
a. Click on the Connections tab at the top of the screen.
b. You will then need to click on the LAN Settings button.
Figure 5: Internet Properties Screen
3. In the Local Area Network (LAN) settings screen, make sure that there is NOT a
check mark on the Use a Proxy server (see Figure 6).
5
Figure 6: LAN Settings
4. When you have verified that there is not a check mark on the Proxy server, click OK
at the bottom of the screen and click OK again to exit Internet Options. This will take
you back to the Control Panel.
5. In the Control Panel, double click on the Network and Sharing Center icon.
6. Click on anage Network connections.
7. Right click on the Local Area Connection and then choose Properties.
6
Figure 7: Network Connections
8. Click on Internet Protocol Version 4 (see Figure 8 on next page), and then click on
Properties. If not already selected, click the Obtain an IP Address Automatically
radio button.
7
Figure 8: IP Properties
9. Once all of these settings have been checked, you can click OK or Close at the bottom
of the screen. Close all open windows by clicking OK or File Close. If any changes
were made, you may need to restart your computer. Click OK at the prompt. If you are
not prompted to restart, we suggest that you restart your computer manually.
8
INTERNET EXPLORER BROWSER SETUP INSTRUCTIONS
1. Double click on Internet Explorer (the big blue ). If it tries to connect, click
Work Offline. If it comes up with an Internet Connection Wizard, choose I
already have a connection or Set Up anually.
2. Once Internet Explorer starts, if the error message Page cannot be found comes
up, click OK.
3. Click Tools at the top of the screen.
4. Select Internet Options.
5. Under the General tab, type www.alphacomm.net for your home page location.
6. Click on the Connections tab.
7. If any connections are listed in Dial-Up Connections, remove them.
8. Click OK.
You have completed the Internet Explorer (IE) portion of the setup. Happy browsing!
It is now time to set up your email account.
9
E AIL SETUP
Windows ail
Follow these instructions after setting up your Internet Explorer Browser. Note: Windows
mail may repeat some of the settings. If you are switching from Alphacomm.net dial-up to
Alphacomm.net DSL, you should not have to make any changes.
1. Double click the Windows ail icon. NOTE: If this is the first time you are using
Windows mail, skip to step 4.
2. Click on Tools and then click Accounts and choose next.
3. Click on Add, click Email account and then click next.
4. In the Display name box, enter the name you would like displayed when you send an
email; i.e., John Smith. This name can be anything you like. Click Next.
5. In the Email address box, enter your Alphacomm.net email address; i.e.,
johnsmith@alphacomm.net. Click Next.
6. At the Email Server Names screen, verify that the y incoming mail server is a
box displays POP3, not I AP or HTTP. If it doesn’t, select POP3 from the drop down
box.
7. In the Incoming mail (POP3, I AP, or HTTP) server box enter:
mail.alphacomm.net.
8. In the Outgoing mail (S TP) server box enter: mail.alphacomm.net
9. Place a check in the Outgoing Server Requires Authentication box and then click
Next.
10. The next screen will ask for your Email Username information. Click in the line next to
E-mail Username and enter your full email address like the following:
yourusername@alphacomm.net
Your username can be found on your Alphacomm.net Customer Information Sheet, or
you can call Support at 877-450-3500 (toll free) or 906-639-3500 (local). The account
name is case sensitive, so enter it exactly as shown on the customer information sheet.
11. Click in the Password line and type your password. The password is case sensitive, so
be sure to enter it exactly as it appears on the customer information sheet.
12. You may also check the Remember Password option.
13. Click Next, then click Finish, then click Close.
10
NOTE: Some versions may include these additional steps:
•Choose, I connect using a Local Area Connection.
•Click Next, then click Finish.
YOU HAVE CO PLETED THE DSL SETUP!
THANK YOU FOR CHOOSING ALPHACO
.NET!
Otros manuales para CT-5611T
1
Tabla de contenidos
Otros manuales de Módem de Comtrend Corporation
Comtrend Corporation
Comtrend Corporation NL-3120 Manual
Comtrend Corporation
Comtrend Corporation PG-9172AC Manual de usuario
Comtrend Corporation
Comtrend Corporation NexusLink 3120 Manual de instrucciones
Comtrend Corporation
Comtrend Corporation PowerGrid-9182AC Manual de usuario
Comtrend Corporation
Comtrend Corporation VI-3234u Manual de usuario
Comtrend Corporation
Comtrend Corporation CT-5072T Manual de usuario
Comtrend Corporation
Comtrend Corporation NexusLink 5700 Manual de usuario
Manuales populares de Módem de otras marcas
US Robotics
US Robotics 3453C Manual de usuario
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario
Zte
Zte MF823 Manual de usuario
Four-Faith
Four-Faith F1403 Manual de usuario
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manual de usuario
Gemtek
Gemtek WiMAX WIXFBR-103 Manual de usuario