Comtrend Corporation PowerGrid 9142s Manual de usuario

Page 1

Quick Installation Guide

PG-9142s

Powerline Ethernet Adapter

with WiFi

Page 2

Introduction

NOTE: An additional PowerGrid 9142s (or PG-9141s or PG-

9141s-PoE unit) and Ethernet cable are required for each

additional device (e.g. PC, Camera, Access Point) that you

wish to connect to the network, with a minimum of 2 units

required for setup.

A. Initial Setup

NOTE: These steps show how to connect a PowerGrid 9141s unit to a

modem or router. This guide assumes that a PowerGrid 9141s will be

the primary connection to the modem/router and the PowerGrid 9142s

will be used within the network to connect to a WiFi capable device (e.g.

Tablet, IP Phone, Access Point).

1. Ensure that your modem or router is powered on.

2. Plug a PowerGrid 9141s unit into the power outlet closest to the

modem/router. The Power LED will blink GREEN.

3. Connect the PowerGrid 9141s unit to the LAN port of the

modem/router with an Ethernet (RJ-45) cable. Wait 10 seconds for

the PowerGrid’s ETHERNET LED and POWER LED to light up

GREEN indicating a stable connection.

Page 3

B. Device Connection

These steps show how to connect a PowerGrid 9142s to a network

device. Below we use an Ethernet camera as a network device.

1. Plug a PowerGrid 9142s unit into the power outlet closest to the

camera or other device. The Power LED on the PowerGrid

9142s should light up GREEN.

2. Power on your camera (or Ethernet device). Connect the

PowerGrid 9142s to the camera with an Ethernet cable. The

ETHERNET LED on the PowerGrid 9142s should light up

GREEN.

3. The Status LED on thePowerGrid 9142s(s) should now be RED,

GREEN or ORANGE.

4. If the Status LED is off, press the “Config” button on each of the

two PowerGrid 9142s and 9141s devices for 2-11 seconds. Upon

successful connection of the PowerGrid 9141s, the STATUS LED will

light up.

5. If the connection process is not successful, please refer to the

trouble shooting steps in section D.

C. Adding a New Device

Follow steps 1-4 in Part B to add additional PowerGrid 9142s devices to

the network. Press the “Config” button on the new device and one

other PowerGrid device in the network so they can pair and transmit

data successfully.

Page 4

D. PowerGrid 9142s WiFi setup

1. To connect your WiFi device (e.g.

computer, tablet, smartphone) to

the PowerGrid 9142s WiFi adapter,

go to your device’s WiFi settings to

search for -and select- the SSID

that is located on your PowerGrid

9142s device label.

2. When prompted, input the WiFi key located on the PowerGrid 9142s

device label to connect.

3. You should now be successfully connected to the PowerGrid 9142s

WiFi network.

Note: To configure the WiFi settings of your PowerGrid 9142s using a

desktop computer/laptop via an Ethernet cable, please refer to section

2-2 & 2-3 of your user manual for more details.

E. WPS Setup

If your client (e.g. smartphone, notebook, tablet) supports WPS (WiFi

Protected Setup) then you can use this method to set up your

PowerGrid 9142s’ WiFi network.

1. Press and hold the WPS button

for more than 2 seconds on the

PowerGrid 9142s to activate its

WPS. The PowerGrid 9142s’

WPS LED should flash to

indicate a WPS connection is in

progress.

Page 5

2. Within two minutes, press the WPS button (often the WPS/Reset

button) on your client to activate WPS.

Note: Please check the instructions for your wireless client for how

long you need to hold down its WPS button to activate WPS.

3. The devices will establish a connection. You can now connect to the

PowerGrid 9142s’ wireless network with a WiFi device, as described

in section B. To confirm a successful connection you can see if your

client device (e.g. smartphone, notebook, tablet) displays the WiFi

connected icon.

F. Troubleshooting

The following information should help you diagnose basic setup or

installation problems.

1. POWER LED is OFF: If the POWER LED goes off, please make

sure that your power outlet is working properly (perhaps by testing

with another device).Then plug in your PowerGrid 9142s again. If

the POWER LED does not light up, please contact your equipment

supplier for further information.

Page 6

2. ETHERNET LED is OFF: If the ETHERNET LED fails to light up,

check that the LAN port of the PowerGrid unit is connected firmly to

the LAN port of the other device. To check the condition of the

Ethernet cable, use another cable to test the same connection.

3. STATUS LED is OFF: Plug both PowerGrid units that you’re

attempting to pair into power outlets that are within the same room;

both PowerGrid devices should have an Ethernet cable connected to

their respective devices (e.g. PC, Router, Set Top Box, camera, etc.).

After 10 seconds (approximately, until all the LEDs of the device

blink), the STATUS LED should light up GREEN. If not, press the

“Config”button on each for 2-5 seconds and let go.

* If you have tried all of the above and are still experiencing problems, you can reset

both devices to factory default by using a pin - PowerGrid 9141s and button -

PowerGrid 9142s to push the “Reset”button of each device for 11 seconds. The WPS

LED will flash every second. After the “Reset”button is released, the WPS LED will be

steady ON for around 5 seconds, then the system will reboot to factory defaults.

SURGE PROTECTED POWER STRIPS: Avoid plugging

PowerGrid units into power strips with surge protection as

this will reduce network speed and may even prevent

their use.

FOR MORE HELP: If you have further questions or require personal

assistance, please contact your equipment supplier or service provider.

Reset

PowerGrid 9142s

Reset

PowerGrid 9141s

Page 7

Version PG-9142_QIG_V1.0

Otros manuales para PowerGrid 9142s

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Adaptador de Comtrend Corporation

Comtrend Corporation

Comtrend Corporation PG-9172PoE Manual de usuario

Comtrend Corporation

Comtrend Corporation PowerGrid-9171n Manual de usuario

Comtrend Corporation

Comtrend Corporation PowerGrid -9172PoE Manual de usuario

Comtrend Corporation

Comtrend Corporation PG-9171n Manual de usuario

Comtrend Corporation

Comtrend Corporation PG-9182A Manual de usuario

Comtrend Corporation

Comtrend Corporation PowerGrid-9172 Manual de usuario

Comtrend Corporation

Comtrend Corporation WD-1030 Manual de usuario

Comtrend Corporation

Comtrend Corporation WD-1030 Manual de usuario

Comtrend Corporation

Comtrend Corporation GCA-7000 Manual de usuario

Comtrend Corporation

Comtrend Corporation PowerGrid 902 Manual de instrucciones

Comtrend Corporation

Comtrend Corporation PG-9182PoE Manual de usuario

Comtrend Corporation

Comtrend Corporation PG-9182S4 Manual de usuario

Comtrend Corporation

Comtrend Corporation GCA-7000 Manual de usuario

Comtrend Corporation

Comtrend Corporation PowerGrid 902 Manual de usuario

Comtrend Corporation

Comtrend Corporation GCA-6000 Manual de usuario

Comtrend Corporation

Comtrend Corporation WD-1021 Manual de usuario

Comtrend Corporation

Comtrend Corporation PG-9172PT Manual de usuario

Comtrend Corporation

Comtrend Corporation PowerGrid 902 Manual de instrucciones

Comtrend Corporation

Comtrend Corporation PowerGrid 9020 Manual de instrucciones

Comtrend Corporation

Comtrend Corporation PowerGrid-9141(s) Manual de usuario

Comtrend Corporation

Comtrend Corporation PG-9172AC Manual de usuario

Comtrend Corporation

Comtrend Corporation PG-9172 Manual de usuario

Comtrend Corporation

Comtrend Corporation PowerGrid 9141s-PoE Manual de usuario

Comtrend Corporation

Comtrend Corporation PG-9182PT Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario