CompuLab Fitlet3 Manual de usuario

Owner’s Manual

Revision 1.1

Feb-2022

www.fit-iot.com

Page 2 of 22

fitlet3 owner’s manual

Hayetsira St. 17, Yokneam, Israel

Tel: +972-48-290-168 | Fax: +972-48-325-251 | www.fit-iot.com

Safety instructions

Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your

personal safety. Unless otherwise noted, each procedure included in this document assumes that you have read the

safety information that shipped with your computer

WARNING: Disconnect all power sources before opening the

computer cover or panels. After you finish working inside

the computer, replace all covers, panels, and screws

before connecting to the power source.

CAUTION: Some repairs may only be done by a certified

service technician. You should only perform

troubleshooting and simple repairs as authorized in your

product documentation, or as directed by the online or

telephone service and support team. Damage due to

servicing, that is not authorized by Compulab, is not

covered by your warranty. Read and follow the safety

instructions that came with the product.

CAUTION: To avoid electrostatic discharge and prevent

internal components damage from electrostatic discharge when

touching computer or its parts, ground yourself by using a

wrist grounding strap or by periodically touching an

unpainted metal surface, such as a connector on the back of

the computer.

CAUTION: Handle components and cards with care. Do not

touch the components or contacts on a card. Hold a card by

its edges or by its metal mounting bracket. Hold a component

such as a processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector

or on its pull-tab, not on the cable itself. Some cables

have connectors with locking tabs; if you are disconnecting

this type of cable, press in on the locking tabs before you

disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins.

Also, before you connect a cable, ensure that both

connectors are correctly oriented and aligned.

www.fit-iot.com

Page 3 of 22

fitlet3 owner’s manual

Hayetsira St. 17, Yokneam, Israel

Tel: +972-48-290-168 | Fax: +972-48-325-251 | www.fit-iot.com

Table of contents

SAFETY INSTRUCTIONS....................................................................................2

INTRODUCTION ..................................................................................................4

SPECIFICATIONS............................................................................................. 5

FEATURES ....................................................................................................... 5

DIMENSIONS.................................................................................................... 6

INTERFACES.................................................................................................... 6

EXPANSION BOARDS ......................................................................................... 7

OPTIONAL ACCESSORIES .................................................................................. 7

CONNECTORS LAYOUT........................................................................................ 8

QUICK START GUIDE........................................................................................9

MINIMUM REQUIREMENTS .................................................................................. 9

IDENTIFYING FITLET3CONFIGURATION ........................................................... 9

OPENING FITLET3........................................................................................... 9

INSTALLING RAM.......................................................................................... 11

M.2 COOLING PLATE,SSD AND MODEM......................................................... 12

RTC BATTERY ............................................................................................... 17

INSTALLING RTC BATTERY............................................................................ 17

RE-ASSEMBLING FITLET3.............................................................................. 18

CONNECTING FITLET3.................................................................................... 19

ENTERING BIOS SETUP ................................................................................ 20

INSTALLING AND BOOTING OPERATING SYSTEM ............................................... 20

SERVICE...........................................................................................................21

SUPPORT ....................................................................................................... 21

WARRANTY ..................................................................................................... 21

RMA ............................................................................................................. 21

For more information and to obtain the latest revision of

this document, please visit: www.fit-iot.com

For technical support and product related questions,

please email: [email protected]

www.fit-iot.com

Page 4 of 22

fitlet3 owner’s manual

Hayetsira St. 17, Yokneam, Israel

Tel: +972-48-290-168 | Fax: +972-48-325-251 | www.fit-iot.com

Introduction

Thank you for purchasing fitlet3. It is a miniature PC designed to be tough,

capable, versatile and user-friendly. With proper installation, we expect

fitlet3 to serve you for many years. The unique fanless design of fitlet3

eliminates the need for any maintenance after installation.

Please consult this owner’s manual for getting started with fitlet3. You are

welcome to contact fitlet3 manufacturer –Compulab at www.fit-iot.com or

support@fit-pc.com should you have any technical questions.

fitlet3 features

•Intel Elkhart Lake CPU

•Up to 32 GB DDR4 RAM

•NVMe | M.2 SATA | 2.5” storage*

•Dual head 4K display

•Up to 4 Gbit Ethernet ports* | WiFi* | cellular communication*

•USB 3.1, USB 2.0, audio*, optional Isolated serial + GPIO ports, indicator

LED

•Supports Windows 10, Windows 11 and Linux

•Can be extended with Function And Connectivity Extension T-Cards (FACET

Cards)

•All-metal fanless housing 132.8 mm X 100 mm X 34.8 mm

•Operating temperature range is from -40°C to 85°C (depending on ordered

configuration)

*Feature is not assembled by default or may require an extension FACET card

Package contents

1. fitlet3 computer

2. Power supply: input 100-240VAC 50/60Hz, output 12VDC 3A with universal AC plugs

3. Antennas, according to configuration

4. Owner’s manual

NOTES

•Additional accessories can be purchased separately here:

https://fit-iot.com/web/products/fitlet3/buy-fitlet3/

•Some fitlet3 configurations come pre-installed with additional devices and

accessories

www.fit-iot.com

Page 5 of 22

fitlet3 owner’s manual

Hayetsira St. 17, Yokneam, Israel

Tel: +972-48-290-168 | Fax: +972-48-325-251 | www.fit-iot.com

Specifications

Features

IOT gateway / Fanless industrial PC

Intel® Atom Elkhart Lake processor

NVMe + SATA storage

2x/4x Gigabit LAN

Optional Wi-Fi/BT + LTE/5G modem

Optional Isolated serial + GPIO ports

7V –42V DC power input

CPU

Intel® Atom x6425E

4 Core | Base: 2.0 GHz, Boost: 3.0 GHz | TDP: 12 W

Intel® Celeron J6412

4 Core | Base: 2.0 GHz, Boost: 2.6 GHz | TDP: 10 W

Intel® Atom x6211E

2 Core | Base: 1.3 GHz, Boost: 3.0 GHz | TDP: 6 W

Memory

Type

SO-DIMM DDR4 up to 3200MT/s

Max. capacity

32 GB

Storage

M.2 Key-M

PCIe x4 / SATA for M.2 NVMe or SATA, size up to 2280

M.2 Key-B

SATA for M.2 SATA, size up to 2260

2.5” HDD/SSD

Optional M.2 to SATA expansion for 2.5” HDD / SSD

Display

HDMI

HDMI 1.4b (up to 3840 x 2160 @ 30Hz)

Mini-Display Port

DP 1.2 (up to 4096 x 2160 @ 60Hz) Dual mode

Ethernet

Type

2x Gigabit Ethernet on RJ45

Controllers

2x Internal MAC with discreet PHY

Speed

1000 Mbps / 100 Mbps / 10 Mbps

Optional FC3-LAN

Additional 2x GbE LAN on RJ45

Optional FC3-OPLN

Additional 1x GbE LAN on SFP+ for optical LAN

Optional FC3-POED

Additional 1x GbE LAN on RJ45 with PoE device capabilities

Wireless

Connectivity

On-board

Optional On-board module with Wi-Fi 6E, BT 5.2

M.2 Key-E 1

For M.2 2230 module with Wi-Fi 6E, BT 5.2

M.2 Key-B

For M.2, LTE/5G modem, with micro-SIM tray

USB

USB 2.0

4x USB 2.0 on USB Type-A

USB 3.1

2x USB 3.1 on USB Type-A

Serial/GPIO

Type

Isolated serial and GPIO, up to 24V, on terminal block

Serial port

Optional isolated RS-232/422/485

GPIO

2x isolated GPI + 2x isolated GPO

Audio

Codec

Optional audio codec

Interfaces

Optional analog output, analog input on 3.5 mm jacks

Power

Input power

7V –42V, up to 5A DC input

Connector

5.5 mm power jack w/ locking

Power supply unit

Including universal AC wall mount power supply

Optional FC3-PoE

Input power by PoE, GbE LAN on RJ45

TPM

Internal fTPM

Intel® PTT

Discreet TPM

Optional discreet TPM 2.0

OS support

Windows 10

Windows 10 Pro / Windows 10 LTSC 2021 IoT Enterprise

Windows 11

Windows 11 Pro

Linux

Linux Mint / Ubuntu

Operating

Environment

Commercial temperature

0°C to 45°C

Extended temperature

-20°C to 70°C

Industrial temperature

-40°C to 85°C

Humidity

5% - 95% non-condensing

Physical

Characteristics

Cooling

Fanless, passive cooling

Dimensions

132.8 mm X 100 mm X 34.8 mm

Weight

~ 420 gr.

Mounting

Side / bottom VESA / DIN Rail mount

www.fit-iot.com

Page 6 of 22

fitlet3 owner’s manual

Hayetsira St. 17, Yokneam, Israel

Tel: +972-48-290-168 | Fax: +972-48-325-251 | www.fit-iot.com

Dimensions

Interfaces

Location

Connector

Interface

Front Panel

2x USB Type-A

2x USB 2.0

1x HDMI

HDMI 1.4b (up to 3840 x 2160 @ 30Hz)

1x mini-DP

DP 1.2 (up to 4096 x 2160 @ 60Hz) Dual mode

1x 5.5 mm power jack

7V –42V DC power input

1x terminal block (Optional)

Isolated RS-232/422/485 + 2x GPI + 2x GPO

2x RJ45

2x 10/100/1000 Mbps Ethernet

Rear Panel

Power button

On/Off push button w/ power LED

2x USB Type-A

2x USB 3.1

2x 3.5 mm jacks (Optional)

Analog output, analog input audio

Micro-SIM tray

Micro-SIM Tray for M.2 LTE/5G modem

LED

Debug/programmable LED

2x USB Type-A

2x USB 2.0

Right Panel

2x SMA (Optional)

2x SMA antennas for Wi-Fi/BT or cellular modem

Left Panel

FACET card connectors (Optional)

Ethernet, serial, etc. from FACET expansion card

2x SMA (Optional)

2x SMA antennas for Wi-Fi/BT or cellular modem

Location

Connector

Form factor

Interface

Usage

Internal Top

SO-DIMM

DDR4 SO-DIMM

DDR4

DDR4 module

Internal

Bottom

M.2 Key-M

M.2 up to 2280 or

Optional 2.5” SATA storage 1

PCIe Gen 3 x4 / SATA

-NVMe/SATA storage

-M.2 PCIe x1x HDMI

M.2 Key-B

M.2 Up to 3060 or

Optional 2.5” SATA storage 1

PCIe Gen 3 x1 /SATA

USB 2.0

-LTE/5G modem

-SATA storage

M.2 Key-E

M.2 2230 or

FACET expansion card 2

PCIe Gen 3 x2

USB 2.0

-Wi-Fi/BT module

-FACET card

Notes:

1. Up to 1 unit of 2.5” SATA storage expansion (EB-M2SATA) is possible

2. FACET expansion card and Wi-Fi/BT card are mutually exclusive. For Wi-Fi/BT on systems with FACET cards,

on-board Wi-Fi/BT module bust be selected.

www.fit-iot.com

Page 7 of 22

fitlet3 owner’s manual

Hayetsira St. 17, Yokneam, Israel

Tel: +972-48-290-168 | Fax: +972-48-325-251 | www.fit-iot.com

Expansion boards

Name

Description

Compatible connector

FC3-LAN

2x GbE LAN on RJ45

M.2 Key-E (FACET) 1

FC3-POED

GbE LAN PoE device on RJ45

M.2 Key-E (FACET) 1

FC3-OPLN

GbE on SFP+ for optic LAN

M.2 Key-E (FACET)1

EB-M2SATA

SATA expansion for 2.5” HDD /

SSD 2,3

M.2 Key-M or M.2 Key-B

Notes:

1. FACET expansion card and Wi-Fi/BT card are mutually exclusive. For Wi-Fi/BT on systems with FACET cards,

on-board Wi-Fi/BT module bust be selected.

2. Up to 1 unit of EB-M2SATA is possible, and up to two storage devices in total.

3. EB-M2SATA expansion requires deep bottom that will enlarge the fitlet3 size.

Optional accessories

Name

Description

FITLET3-ACC-PSU

Universal power supply unit (one units is included in fitlet3 package)

FITLET3-ACC-BRKT

VESA mounting bracket

FITLET3-ACC-DIN

DIN rail mounting kit (Requires VESA mounting bracket)

FITLET3-ACC-DINSD

Side DIN rail mounting kit (does not require VESA mounting bracket)

FITLET3-ACC-POWBTN

Remote power button with LED with 25cm wire

www.fit-iot.com

Page 8 of 22

fitlet3 owner’s manual

Hayetsira St. 17, Yokneam, Israel

Tel: +972-48-290-168 | Fax: +972-48-325-251 | www.fit-iot.com

Connectors’ layout

www.fit-iot.com

Page 9 of 22

fitlet3 owner’s manual

Hayetsira St. 17, Yokneam, Israel

Tel: +972-48-290-168 | Fax: +972-48-325-251 | www.fit-iot.com

Quick start guide

Minimum requirements

To use fitlet3 you will need:

•RAM and storage device (if not pre-installed)

•A display with HDMI or DisplayPort input + HDMI or mini-DisplayPort cable

•USB keyboard and mouse

Identifying fitlet3 configuration

fitlet3 configuration is detailed on the label attached to the bottom side of the

computer.

Note

Pay attention to RAM and storage. If not installed, fitlet3 will not boot. You will

have to install these devices firstly.

www.fit-iot.com

Page 10 of 22

fitlet3 owner’s manual

Hayetsira St. 17, Yokneam, Israel

Tel: +972-48-290-168 | Fax: +972-48-325-251 | www.fit-iot.com

Opening fitlet3

You will need to open fitlet3 in order to install RAM, storage and RTC battery.

Required tool: Phillips screwdriver.

To open fitlet3 please follow these steps:

1.Place fitlet3 on a flat surface bottom-up.

2.Open the four screws using the Phillips screwdriver (counter clock-wise).

3.Lift the bottom cover to remove it. Side panels should fall-off.

4.Lift fitlet3 from the top cover

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de De oficina de CompuLab

CompuLab

CompuLab Fitlet2 FC-POED Manual de usuario

CompuLab

CompuLab Airtop3 Manual de usuario

CompuLab

CompuLab FIT-PC4 Manual de usuario

CompuLab

CompuLab Tensor-I22 Manual de usuario

CompuLab

CompuLab Fitlet-H Manual de usuario

CompuLab

CompuLab Fitlet FC-OPLN Manual de usuario

CompuLab

CompuLab IPC2 Manual de usuario

CompuLab

CompuLab Airtop2 Manual de usuario

CompuLab

CompuLab fitlet Manual de usuario

CompuLab

CompuLab UTILITE2 Manual de usuario

CompuLab

CompuLab IPC3 Manual de usuario

CompuLab

CompuLab SBC-FITPC3 Manual de usuario

CompuLab

CompuLab Airtop-C0 Manual de usuario

CompuLab

CompuLab Trim-Slice Manual de usuario

CompuLab

CompuLab fitlet2 FC-USB Manual de usuario

CompuLab

CompuLab fit-PC2 Manual de usuario

CompuLab

CompuLab Airtop Manual de usuario

CompuLab

CompuLab fit-PC2i Manual de usuario

CompuLab

CompuLab fitlet2 FC-USB Manual de usuario

CompuLab

CompuLab fitlet2 FC-USB Manual de usuario

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario

CompuLab fitlet3 Manual de usuario

Manuales populares de De oficina de otras marcas