Comnet CLFE4+1SMS[POE](C Manual de usuario

INS_CLFE4+1SMS[POE](C,U)_REV– 10/27/11 PAGE 1TECH SUPPORT: 1.888.678.9427

INSTALLATION AND OPERATION MANUAL

CLFE4+1SMS[POE](C,U) Series

10/100 4TX+1EX ETHERNET SELF-MANAGED SWITCH

WITH POWER OVER ETHERNET (POE+)

The ComNet™CopperLine® CLFE4+1SMS[POE](C,U) is a five-port Ethernet switch

with uplink management functionality and provides 4 copper ports operating at

10/100Mbps and is designed to combine four electrical ports into a single electrical

Cat5, UTP or Coax CopperLine port that forwards this data to the next network device.

There is no programming required to use this product. The ComNet CLFE4+1SMS

comes pre-programmed, preventing network video flooding with DIP switch selection

of the fifth electrical port as uplink or as an unmanaged switch. Ports 1–4 of the

CLFE4+1SMSPOE can supply up to thirty (30) watts of Power over Ethernet (PoE) and

incorporate PoE+ features based on the IEEE 802.3at standard. It is “Plug-and-Play”.

Bi-color (Red/Green) LED indicators are provided for rapidly ascertaining equipment

operating status. Table 2 on Page 7 describes the LED indicators for each light on

the unit.

These units are interchangeable between stand-alone or card mount configurations,

or may be DIN-rail mounted by the addition of ComNet model DINBKT1 or DINBKT4

adaptor plate. See Figure A on Page 10 for mounting instructions.

This manual serves the following

ComNet Model Numbers:

CLFE4+1SMSC

CLFE4+1SMSU

CLFE4+1SMSPOEC

CLFE4+1SMSPOEU

INS_CLFE4+1SMS[POE](C,U)_REV– 10/27/11 PAGE 2

INSTALLATION AND OPERATION MANUAL CLFE4+1SMS[POE](C,U) SERIES

TECH SUPPORT: 1.888.678.9427

FIGURE 1 – CLFE4+1SMSPOEC FOUR CHANNEL SURFACE OR RACK MOUNT COAX UNIT WITH POE

FIGURE 2 – CLFE4+1SMSPOEC FOUR CHANNEL SURFACE OR RACK MOUNT COAX UNIT WITH POE

EXTENDED

DISTANCE

PORT 4

ETHERNET

PORT 3

ETHERNET

PORT 2

ETHERNET

PORT 1

ETHERNET

Operating Power: 9 to 12 VDC (non-PoE), 48 to 56VDC (PoE)

Power Consumption: 10W (non-PoE), 130W (Max PoE)

Black w/ White

Stripe (GND)

Black (+Vin)

POE–

POE+

10/100 data rate DIP switch

Local/Remote DIP switch

Managed/Unmanaged DIP switch

See Installation Instructions

CLFE4+1SMSPOEC Front Panel CLFE4+1SMSPOEC Rear Panel

Do not use for

POE Applications.

INS_CLFE4+1SMS[POE](C,U)_REV– 10/27/11 PAGE 3

INSTALLATION AND OPERATION MANUAL CLFE4+1SMS[POE](C,U) SERIES

TECH SUPPORT: 1.888.678.9427

EXTENDED

DISTANCE

PORT 4

ETHERNET

PORT 3

ETHERNET

PORT 2

ETHERNET

PORT 1

ETHERNET

FIGURE 3 – CLFE4+1SMSPOEU FOUR CHANNEL SURFACE OR RACK MOUNT UTP UNIT WITH POE

FIGURE 4 – CLFE4+1SMSPOEU FOUR CHANNEL SURFACE OR RACK MOUNT UTP UNIT WITH POE

Operating Power: 9 to 12 VDC (non-PoE), 48 to 56VDC (PoE)

Power Consumption: 10W (non-PoE), 130W (Max PoE)

Black w/ White

Stripe (GND)

Black (+Vin)

Do not use for

POE Applications.

POE–

POE+

10/100 data rate DIP switch

Local/Remote DIP switch

Managed/Unmanaged DIP switch

1 Pair/4 Pair DIP switch

See Installation Instructions

CLFE4+1SMSPOEU Front Panel CLFE4+1SMSPOEU Rear Panel

INS_CLFE4+1SMS[POE](C,U)_REV– 10/27/11 PAGE 4

INSTALLATION AND OPERATION MANUAL CLFE4+1SMS[POE](C,U) SERIES

TECH SUPPORT: 1.888.678.9427

FIGURE 5 – CLFE4+1SMSC FOUR CHANNEL SURFACE OR RACK MOUNT COAX UNIT

FIGURE 6 – CLFE4+1SMSC FOUR CHANNEL SURFACE OR RACK MOUNT COAX UNIT

EXTENDED

DISTANCE

PORT 4

ETHERNET

PORT 3

ETHERNET

PORT 2

ETHERNET

PORT 1

ETHERNET

Operating Power: 9 to 15 VDC

Power Consumption: 10W

Black w/ White

Stripe (GND)

Black (+Vin)

CLFE4+1SMSC Front Panel CLFE4+1SMSC Rear Panel

10/100 data rate DIP switch

Local/Remote DIP switch

Managed/Unmanaged DIP switch

See Installation Instructions

INS_CLFE4+1SMS[POE](C,U)_REV– 10/27/11 PAGE 5

INSTALLATION AND OPERATION MANUAL CLFE4+1SMS[POE](C,U) SERIES

TECH SUPPORT: 1.888.678.9427

EXTENDED

DISTANCE

PORT 4

ETHERNET

PORT 3

ETHERNET

PORT 2

ETHERNET

PORT 1

ETHERNET

FIGURE 7 – CLFE4+1SMSU FOUR CHANNEL SURFACE OR RACK MOUNT COAX UNIT

FIGURE 8 – CLFE4+1SMSU FOUR CHANNEL SURFACE OR RACK MOUNT UTP UNIT

Operating Power: 9 to 15 VDC

Power Consumption: 10W

Black w/ White

Stripe (GND)

Black (+Vin)

CLFE4+1SMSU Front Panel CLFE4+1SMSU Rear Panel

10/100 data rate DIP switch

Local/Remote DIP switch

Managed/Unmanaged DIP switch

1 Pair/4 Pair DIP switch

See Installation Instructions

INS_CLFE4+1SMS[POE](C,U)_REV– 10/27/11 PAGE 6

INSTALLATION AND OPERATION MANUAL CLFE4+1SMS[POE](C,U) SERIES

TECH SUPPORT: 1.888.678.9427

IMPORTANT NOTE. PLEASE READ. The applications are

shown as general representations only and are not intended

to show detailed network topologies. Your actual network

will differ, requiring changes or perhaps additional network

equipment to accommodate the systems as illustrated.

Please contact ComNet’s Design Center to discuss your

specific requirements.

Ethernet Connection

PoE Power

Extended Connection

PoE Camera

Ethernet

Switch

Local Remote

CLFE1EO(C,U) CLFE4+1SMSPOE(C,U)

Power

48V to 56V

Power

IP Camera

Power

IP Camera

Power

IP Camera

Power

IP Camera

Ethernet

Switch

Local Remote

CLFE1EO(C,U)

CLFE4+1SMS(C,U)

Power

9V to 15V

APPLICATION DIAGRAM

Note: Coaxial applications use the CLFE4+1SMS[POE]Cand CLFE1EOC;

UTP applications use the CLFE4+1SMS[POE]Uand CLFE1EOU.

Remote PoE Injection Mode

Non-PoE Mode

INS_CLFE4+1SMS[POE](C,U)_REV– 10/27/11 PAGE 7

INSTALLATION AND OPERATION MANUAL CLFE4+1SMS[POE](C,U) SERIES

TECH SUPPORT: 1.888.678.9427

INSTALLATION INSTRUCTIONS

1 - SET DATA RATE DIP SWITCHES

Locate the 10/100 data rate DIP switch on the unit.

Set the data rate according to bandwidth required. The default setting for the data rate DIP switch is 100Mbps.

NOTE: The data rate must be set the same on both the local and remote units.

2 - SET WIRE PAIR DIP SWITCHES (UTP MODELS ONLY, FOR COAX MODELS SKIP TO STEP 3)

Locate the wire pair DIP switch on the unit.

Set the pair according to number of twisted wire pairs used (1 or 4). The default setting for the wire pair DIP switch is 4 pair.

NOTE: The number of pairs selected must be set the same on both the local and remote units.

3 - SET LOCAL/REMOTE DIP SWITCHES

Set the Local/Remote switch to Local (L) for Local (head end) devices or Remote (R) for Remote (field end) devices.

The default setting for this switch is Remote.

4 - SET MANAGED/UNMANAGED DIP SWITCHES

Set the Managed/Unmanaged switch to the “Managed” position. The default setting for this switch is Managed.

NOTE: In most cases, you will want to set the unit to “Managed” to prevent port flooding.

5 - CONNECT EXTENDED WIRING

Connect Extended Distance Port to field wiring.

6 - CONNECT NETWORK WIRING

Using CAT5/5e, connect Local unit to network and Remote unit to camera.

7 - CONNECT POWER

Connect power to unit per the following table:

Table 1 – Power Connections per Use Case

Non-PoE PoE

Operating Voltage 9 to 15 VDC (9 VDC †when in C1 or C2)†48 to 56 VDC

Use Power Connectors GND and +Vin POE+ and POE-

Note: For the PoE models only use the PoE power connectors.

†Contact the ComNet Design Center, or refer to the appropriate installation and operation manual when configuring and specifying power for a deployment.

8 - VERIFY FUNCTIONALITY

See LED table below and Troubleshooting Guide if corrective action is needed.

Table 2 – Indicating LEDs

PWR POE Link (Ethernet Port) Activity (Ethernet Port) EXT LNK

GREEN Power Applied PoE Applied – – 10M or 100M Link Detected

YELLOW – – Link Detected – –

OFF Power Off No PoE Present No Link – No Link

BLINK – – – Data Activity Data Activity

INS_CLFE4+1SMS[POE](C,U)_REV– 10/27/11 PAGE 8

INSTALLATION AND OPERATION MANUAL CLFE4+1SMS[POE](C,U) SERIES

TECH SUPPORT: 1.888.678.9427

TABLE 4 – TROUBLESHOOTING GUIDE

Problem Steps to Take

Indicating LEDs not lighting Check that power is properly applied to the unit using the correct connector pair.

No Communication Check Ethernet Link LEDs, Extended Link LEDs, All Connections, Local/Remote switch is set properly.

Verify that Local units are installed at the head end and that Remote units are installed in the field.

Verify that the Data Rate switches are set to the same data rate on both the Local and Remote units.

Bad Video Make sure Data Rate and 1/4 Pair Switches are set properly, and the extended distance is within specifications (see Table

3 – Approximate Maximum Extended Distances).

Units not reaching estimated max

distances over COAX or UTP

Check extended distance cable and connections. Try connection on a short cable to eliminate possibility of faulty cabling.

Check that the extended distance wire is connected to Extended Distance Port.

Verify that there is no additional equipment (e.g. surge protector) on the Extended Link. The cable should be continuous from

end to end, with no active components.

Not all cameras visible Check that the Managed/Unmanaged DIP switch is set to “Managed.”

TABLE 3 – APPROXIMATE MAXIMUM EXTENDED DISTANCES1

Media COAX - RG59/U UTP - 1 pair UTP - 4 pair

Extended Port Data Rate 10M 100M 10M 100M 10M 100M

Extended Distance15,000 ft

1,524 m

2,000 ft

610 m

3,000 ft

914 m

1,000 ft

305 m

3,000 ft

914 m

2,000 ft

610 m

1Distance figures are obtained using in-house testing mirroring installations. Factors such as coaxial/copper cable quality, the number of connectors/

splices in the cable run, the use of PoE, and environmental conditions encountered within the installation may affect the actual transmission

distance, and should be taken into consideration.

1 Mixed PoE and Non-PoE systems can be implemented.

2 Lower data rates generally provide longer operating distances.

APPLICATION NOTES

INS_CLFE4+1SMS[POE](C,U)_REV– 10/27/11 PAGE 9

INSTALLATION AND OPERATION MANUAL CLFE4+1SMS[POE](C,U) SERIES

TECH SUPPORT: 1.888.678.9427

Recommended part is Wurth Part 742 711 32 S

(Not included). Equivalent parts may be substituted.

LOOPING THE POWER CABLE AROUND THE FERRITE CORE

Attaching the ferrite core to the power cord of the unit helps

prevent RF interference from radio signals.

1. Pull the fixing tab of the ferrite core to open it.

2. Make three loops around the core with the power cable of

the unit.

3. Attach the ferrite core to the unit power cord as shown and

press it until it clicks.

Lift up to release the lock and open the core.

Closed Open

Make three loops around the core with the power cable.

Start winding 5 to 10 cm (2 to 3.9 in) away from the power

connection.

Close the lock. You may now operate the unit according to

instructions.

ATTACHING THE FERRITE CORE TO THE POWER CORD OF THE UNIT (Ferrite core not included, must be purchased separately)

When using v48VDC Power Supplies

INS_CLFE4+1SMS[POE](C,U)_REV– 10/27/11 PAGE 10

INSTALLATION AND OPERATION MANUAL CLFE4+1SMS[POE](C,U) SERIES

FIGURE A

Dimensions are for a ComFit module

8.38cm

[3.3in]

2.7cm

[1.06in]

4.19cm

[1.65in]

0.8cm

[0.31in]

0.4cm

[0.16in]

0.62cm

[0.24in]

6.37cm

[2.50in]

13.2cm

[5.2in]

11.9cm

[4.7in]

15cm

[5.9in]

7.5cm

[2.9in]

0.63cm

[0.25in]

2.75cm

[1.1in]

44.45cm

[17.50in]

48.26cm

[19.0in]

15.44cm

[6.08in]

1.9cm

[0.75in]

4.37cm

[1.72in]

1.9cm

[0.75in]

INSTALLATION CONSIDERATIONS

These units are supplied as Standalone/Rack mounted module. Units

should be installed in dry locations protected from extremes of

temperature and humidity.

WARNING: Unit is to be used with a Listed Class 2 power supply. Although

the units may be mounted inside a ComNet rack the PoE models cannot be

powered from the built-in rack PSU; they must be powered by an external

48-56VDC PSU.

IMPORTANT SAFEGUARDS:

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack

assembly, the operating ambient temperature of the rack environment

may be greater than room ambient. Therefore, consideration should be

given to installing the equipment in an environment compatible with

the maximum ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such

that the amount of air flow required for safe operation of the equipment

is not compromised.

and the “CopperLine Logo” are registered trademarks of Communication Networks.

3 CORPORATE DRIVE | DANBURY, CONNECTICUT 06810 | USA | T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET

Tabla de contenidos

Otros manuales de Enrutador de red de Comnet

Comnet

Comnet CLFE4US1TPC Manual de usuario

Comnet

Comnet CNGE3FE7MS4 Manual de usuario

Comnet

Comnet CWGE2FE24MODMS Manual de usuario

Comnet

Comnet CWFE8TX8MS Manual de usuario

Comnet

Comnet CNGE24FX12TX12MSPOE Manual de usuario

Comnet

Comnet reliance RL1000GW Manual de usuario

Comnet

Comnet CNGE24MS-OB Manual de usuario

Comnet

Comnet CNGE3FE8MSPOE Manual de usuario

Comnet

Comnet CWGE2FE8MSPOE Manual de usuario

Comnet

Comnet CNGE28FX4TX24MS2 Manual del propietario

Comnet

Comnet netwave NW3 Guía de configuración

Comnet

Comnet CWGE9MS Manual de usuario

Comnet

Comnet CNFE10MS Manual de usuario

Comnet

Comnet CNGE2FE8MSPOE Manual de usuario

Comnet

Comnet CNGE2FE24MS Manual de usuario

Comnet

Comnet CNGE11FX3TX8MS Manual de usuario

Comnet

Comnet CNGE24MS Manual de usuario

Comnet

Comnet CWFE2COAX Manual del propietario

Comnet

Comnet RLXE4GE24MODMS Manual de usuario

Comnet

Comnet CNGE20FX4TX16MS Manual del propietario

Comnet

Comnet CNGE3FE8MS Manual de usuario

Comnet

Comnet CNGE8FX4TX4MS Manual de usuario

Comnet

Comnet CNGE5MS Manual de usuario

Comnet

Comnet NW7/M Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad