Comnet netwave NW1 Manual de usuario
NW1
NW9
NW1/M
INSTALLATION AND OPERATION MANUAL
INDUSTRIALLY HARDENED HIGH PERFORMANCE
WIRELESS ETHERNET
Thank you for purchasing NetWave®from ComNet.This installation guide applies to
all NetWaveRadios.
The NetWave industrially hardened wireless Ethernet transmission link from ComNet
can be configured through the embedded User Interface as an AccessPoint.This
point‐to‐multipoint model allows multiple Ethernet endpoints to be connected to a
central AccessPoint.NetWave Radios support up to 500Mbps with their fastest radio
using MIMOTechnology.An easy to read LED array displays unit operational status
along with received signal strength ensuring optimal installation and operation.The
NW1, NW9 and NW1/M family of radios all support 802.3af
FCC radios are certified for the United States. IC radios are certified for Canada.
This manual serves the following
ComNet Series:
INSTALLATION AND OPERATION MANUAL
NETWAvE
INS_NetWave_REV– 06/10/13 PAGE 2
About This Guide
This guide is intended for different users such as engineers, integrators, developers, IT managers,
and technicians.
It assumes that users have some PC competence and are familiar with Microsoft Windows
operating systems and web browsers such as Windows Internet Explorer and Mozilla Firefox, as
well as have knowledge of the following:
»
Installation of electronic equipment
»
Electrical regulations and guidelines
»
Knowledge of Local Area Network technology
Related Documentation
The following documentation is also available:
»
NW1Datasheet
»
NW9Datasheet
»NW1/M Datasheet
»
NetWave Quick Start Guide
Website
For information on ComNet’s entire product line, please visit the ComNet website at
http://www.comnet.net
Support
Safety
»
Only ComNet service personnel can service the equipment. Please contact ComNet Technical
Support.
»
The equipment should be installed in locations with controlled access, or other means of
security, and controlled by persons of authority.
INSTALLATION AND OPERATION MANUAL
NETWAvE
INS_NetWave_REV– 06/10/13 PAGE 3
Contents
About This Guide 2
Overview 5
Legal Information 5
1.0 Introduction 6
6
1.1
System Requirements
2.0 Cabling Requirements 7
7
3.0 Hardware Installation
Outdoor Ethernet Gland Installation
NetWave Indicating LED Details
9
Outdoor Standard Mounting Hardware
9
4.0 Key Default Configurations 10
5.0 Quick Configuration 11
6.0 Detailed Configuration 12
12Getting Started
Buttons and Alerts 13
7.0 Status Tab 14
Overview
14
Wireless AP
15
Associated Stations AP
16
System 17
Memory
17
Network
17
DHCP Leases
17
Routes
18
System Log
18
19 Kernel Log
Real‐time Graphs 20
INSTALLATION AND OPERATION MANUAL
NETWAvE
INS_NetWave_REV– 06/10/13 PAGE 5
Overview
Legal Information
No part of this document may be reproduced or transmitted in any form or by any means,
electronic and mechanical, for any purpose, without the express written permission of ComNet.
Copyright
Copyright © 2015 Communication Networks, LLC (dba ComNet). All rights reserved.
Disclaimer
ComNet reserves the right to make changes in specifications at any time without notice. The
information furnished by ComNet in this material is believed to be accurate and reliable. However,
ComNet assumes no responsibility for its use.
INSTALLATION AND OPERATION MANUAL
NETWAvE
1.0
Introduction
The NetWave industrially hardened wireless Ethernet transmission link from ComNet can be
configured through the embedded User Interface as an Access Point. This point‐to‐multipoint
model allows multiple Ethernet endpoints to be connected to a central Access Point.
NetWave Radios support up to 500Mbps with their fastest radio using MIMO Technology. An easy
to read LED array displays unit operational status along with received signal strength ensuring
optimal installation and operation. The NW1, NW9 and NW1/M family of radios support 802.3af .
This user manual is a guide for the NetWave Wireless Radios as well as the preconfigured kits.
ComNet NetWave Wireless offers OpenWRT with the most advanced Qualcomm Atheros wireless
drivers. NetWave now includes a new user‐friendly LuCI web interface for configuring the device.
OpenWRT is an extensible GNU/Linux distribution for embedded devices. It is built from the
ground up to be a full‐featured, easily modifiable operating system. It is powered by a Linux
kernel that's more recent than most other distributions. LuCI is a free, clean, extensible and easily
maintainable web user interface for embedded devices. It has high performance, small installation
size, fast runtimes, and good maintainability. The units come configured point to multipoint
applications.
This manual contains detailed operational and configuration information not covered in the quick
start guides. There some variations in features with each model, please consult the appropriate
data sheet for features and capabilities.
This guide applies toall NetWave Radios.
1.1
System Requirements
Operating System:
Microsoft Windows XP, Windows Vista, Windows 7, Windows 8, Linux, or Mac OS X.
Web Browser:
Mozilla Firefox, Google Chrome, Apple Safari, or Microsoft Internet Explorer 8 or above.
TECHSUPPORT:1.888.678.9427 INS_NetWave_REV– 06/10/13 PAGE 6
INSTALLATION AND OPERATION MANUAL
NETWAvE
INS_NetWave_REV– 06/10/13 PAGE 7
2.0 Cabling Requirements
Shielded CAT 5 or better should be used for all out of plant Ethernet connection and should
be properly grounded through the PoE AC ground. Industrial grade shielded Ethernet cable is
recommended to help prevent ESD damage commonly experienced with outdoor installations.
Visit www.comnet.net/comnet‐products/cables
3.0
Hardware Installation
Outdoor Ethernet Gland Installation
There will be at least one cable gland included with each outdoor enclosure. Below is an image of
the individual parts of the gland with an Ethernet cable routed through.
Note: The split rubber washer allows a pre-terminated Ethernet cable to be used. Use RJ-45
connector without Snagless Jacket.
Once the cable has been routed through the weather connection, and the RJ45 connection has
been made, screw in the gland into the housing making sure it is tight enough for a water tight
seal. Push the split rubber gasket into place and loosely screw the cap that goes over the rubber
washer.
Once the gland is tight in the housing, tighten the outer nut/cap making sure the rubber seal
squeezes and seals the Ethernet cable to the gland as shown below.
INSTALLATION AND OPERATION MANUAL
NETWAvE
INS_NetWave_REV– 06/10/13 PAGE 8
IMPORTANT: Only plug PoE power to Port 1.
Connectinga PoEpowersource to the PSEPort(#2) will
cause a major device malfunction and void the warranty.
Connect one end of an RJ‐45 Ethernet cable to the LAN OUT port of the Power Injection
Module (PIM) and the other end to LAN of the access point – as sown below.
Note: Maximum length of the RJ-45 CAT5 cable is 90 meters.
Connect the RJ‐45 Ethernet cable attached to the PIM to a network device, such as a switch or
to the configuration PC. Then plug the power adaptor to an AC power outlet and power plug
into the socket of the PIM – as shown in the diagram below.
Note: DC Passive PoE input for the NetWave Radios is 24 - 48VDC.
A.
Connect one end of an RJ‐45 Ethernet cable to the OUT
port of the Power Injection Module (PIM) and the other end
to LAN of the access point.
Maximum length of the RJ‐45 CAT5 cable is 100 meters.*
B.
Connect the RJ‐45 Ethernet cable attached to the PIM to a
network device, such as to a switch or to the PC you will use
to configure the access point.
C.
Connect the power adaptor to the main electrical supply
and the power plug into the socket of the PIM.
PoE power input: Passive PoE (range 24 ‐ 48 VDC).
The unit can also be powered by a suitable IEEE 802.3af/at
PSE device such as a PoE switch or injector. Exception: the
NWK11/M Radios only accepts Passive PoE Power.
D.
A Drip Loop is recommended as additional precaution
against moisture entering the Access Point housing.
*Up to 200mW radio. For higher power radio upgrade tohigher rating
power adapter.
Network
Edge Device
P1
P2
B
A
D
C
Ethernet
Network
D
D
INSTALLATION AND OPERATION MANUAL
NETWAvE
INS_NetWave_REV– 06/10/13 PAGE 9
NetWaveIndicatingLEDDetails
LED
VISUAL CUE
INDICATION
POWER
SOLID GREEN
Power is supplied to the unit
OFF
No power is supplied to the unit or the unit is in reset.
LAN
SOLID GREEN
LAN Connected
OFF
No Connectivity
RSSI1
SOLID RED
Weak Connection
RSSI2
SOLID ORANGE
Moderate Connection
RSSI3
SOLID GREEN
Solid Connection
RSSI4
SOLID GREEN
Excellent Connection
(Advisable to check Status Page to confirm RSSI is > ‐55)
SIGNAL STRENGTH:
WEAK SIGNAL EXCELLENT SIGNAL
Outdoor Standard Mounting Hardware
This mounting hardware will support pole diameters up to 2 in (5.8 cm). Below are the parts
contained in the standard mounting hardware.
Here is the mounting hardware assembled shown with a NW1/M in a +30° and ‐30°vertical position
POWER
RSSI1
LAN
RSSI2
RSSI3
RSSI4
INSTALLATION AND OPERATION MANUAL
NETWAvE
INS_NetWave_REV– 06/10/13 PAGE 10
4.0
Key Default Configurations
IP Address of Web Server
LAN Mode for WebServer
192.168.10.100
192.168.10.101 for all others
Static Addressing
Web Server User ID admin
WebServer Password admin
SSID NetWave‐1
WPAPre-shared Key
Channel-Frequency (AP)
ChannelSpectrumWidth
Long Range Parameters
12345678
Auto
20/40M/80M
Enabled and defaulted to 1000m
Note: A Reset to defaults (performed on the ADMIN page or via the RESET button) will erase all
user configurations.
Otros manuales para netwave NW1
4
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Módem de Comnet
Manuales populares de Módem de otras marcas
US Robotics
US Robotics 3453C Manual de usuario
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario
Zte
Zte MF823 Manual de usuario
Four-Faith
Four-Faith F1403 Manual de usuario
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manual de usuario
Gemtek
Gemtek WiMAX WIXFBR-103 Manual de usuario