CommScope DB224 Manual de usuario
PRODUCT DESCRIPTION
The DB224 is a heavy duty, light weight, high gain antenna.
It is suitable for mounting to the top or on the side of a tower.
Clamps for top mounting are supplied with the antenna; an
additional side mount kit (DB5001) must be ordered for side
mounting.
The antenna is a four stack collinear array designed to provide
high gain, broad bandwidth and minimum pattern distortion.
A binary cable harness is used to ensure equal inphase
power distribution to all radiating elements.
ELECTRICAL DESIGN
OPTIONAL RADIATION PATTERN
The DB224 can be used as an omnidirectional antenna
having a gain of 6 dBd or as an elliptical pattern antenna
having a maximum gain of 9 dBd. An omni pattern is
achieved when the four dipole elements are spaced evenly,
every 90° around the mast (Figures 1 and 2). An elliptical
pattern is obtained when all four dipole elements are positioned
in a line (collinear) along the mast. When top mounted, the
omni and elliptical models provide radiation patterns as shown
in Figure 3. When side mounted, the two models provide
significantly different radiation patterns (see SIDE MOUNTING
and Figure 4). The antenna can be changed in the field from
one pattern to the other using ordinary hand tools.
Figure 2. Top View Dipole Alignment
(continued on page 2)
Wear shoes with rubber soles and heels.
Wear protective clothingincluding a long-
sleeved shirt and rubber gloves.
Do not install near power lines. Power lines,
telephone lines, and guy wires look the same.
Assume any wire or line can electrocute you.
Do not install on a wet or windy day or
when lightning or thunder is in the area.
Do not use metal ladder.
Figure 1. Dipole Alignment
SAFETY NOTICE
The installation, maintenance, or removal of an antenna
requires qualified, experienced personnel. CommScope
installation instructions are written for such installation
personnel. Antenna systems should be inspected once a
year by qualified personnel to verify proper installation,
maintenance, and condition of equipment.
CommScope disclaims any liability or responsibility for the
results of improper or unsafe installation practices.
It is recommended that transmit power be turned off
when the field installation is performed. Follow all
applicable safety precautions as shown on this page.
Broad Band Gain Antenna
DB224
095008-000 Revision R, July 2016
Page 1 of 4
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 095008-000 P (07/16)
(Continued from page 1)
TWO PIECE MAST
For ease of handling and to facilitate shipment, the mast is
made in two sections. Assembly of the sections is quite simple
and requires only the use of ordinary hand tools. The unique
center splice assures proper alignment.
LIGHTNING PROTECTION
The aluminum mast with a pointed cap provides a positive
low resistance discharge path to the tower or ground system,
thus affording superior protection against lightning damage.
All radiators are operated at DC ground to provide further
protection against lightning and static buildup.
DUAL ANTENNAS
Dual antenna models are available which include two inde-
pendent antennas on a common mast, each with a separate
feed line terminated at the bottom of the mast. One antenna
is isolated from the other by 30 dB. Model DB224S-( ) con-
sists of two omnidirectional antennas, each having a gain of
3 dBd.
SIDE MOUNTING
When the DB224-( ) and DB224E-( ) antennas are mounted
to the side of a tower the horizontal radiation pattern neces-
sarily becomes distorted. The patterns shown below indicate
the typical pattern shape of the antenna side mounted
on a tower with an 18" to 24" face using the DB5001 Side
Mount Kit.
The DB5001 Side Mount Kit positions the antenna approxi-
mately 18" from the tower and consists of an upper sway
brace, lower bracket (both galvanized) and the necessary
hardware for attaching the bracket to round tower members
up to 3" OD, or angular members up to 2" on a side. Other
size clamps can be supplied on special order.
Figure 3. Radiation Patterns for Top Mounted
DB224-( ) and DB224E-( ) Antennas.
Figure 4. Radiation Patterns
(continued on page 3)
095008-000
Page 2 of 4
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 095008-000 P (07/16)
(Continued from page 2)
INSTALLATION PROCEDURE
After removing the antenna from the shipping box, in-
1.
spect it to be sure all parts are on hand and that there is
no physical damage.
2. Inspect the antenna feed assembly output connector to
determine that it mates with the end of your station trans-
mission line. Do not remove any connectors or cables
from the antenna feed assembly since they are all a
part of the antenna.
3. Verify that the frequency to which the antenna has been
tuned is the frequency on which your radio system is to
operate.
4. Slip the mast sections together and position the bands
as shown in Figure 5. Tighten the bands securely; the
recommended tightening torque is 45-60 in-lbs. Then,
join the connectors, making the connections snug, but
do not apply heavy force with pliers. Carefully wrap
Vapor-Wrap
®
around the connection to seal out moisture
problems. Secure the connectors to the mast with
several wraps of tape (see Figure 5).
5. Attach the furnished DB365 mounting clamps to the
bottom of the antenna mast at the designated locations.
Mount the antenna on the tower with the bottom dipole
above and facing away from the tower.
6. A check of the antenna VSWR as measured at the antenna
is recommended at this point. Note this measurement
carefully, and record it for future reference.
7. After checking the VSWR at the antenna, connect the
station transmission line to the antenna; make the con-
nection snug, but do not apply heavy force with pliers.
To avoid moisture problems, carefully wrap Vapor-Wrap
®
around the connection, smoothing it into the cracks and
over the outer jackets of the transmission line. Failure
to waterproof the cable connection can result in improper
operation of your antenna. Properly secure the feeder
cable and antenna transmission line to the tower in the
best position to avoid physical damage to the cable.
8. After the antenna and transmission line installation has
been completed, a careful check should be made to
ensure that:
• All mechanical connections have been securely made.
• The antenna is mounted on the proper leg of the tower
with sufficient physical clearance.
• All connections have been carefully wrapped with
Vapor-Wrap
®
to prevent moisture problems.
Figure 5. Joining the Mast Sections
095008-000
Page 3 of 4
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 095008-000 P (07/16)
This page intentionally left blank.
095008-000
Page 4 of 4
www.commscope.com
© 2016 CommScope, Inc. All rights reserved.
Visit our website at www.commscope.com or contact your local CommScope representative or BusinessPartner for more information.
All trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. 095008-000 P (07/16)
Otros manuales de Antena de CommScope
CommScope
CommScope CMAX-OUS1-UW-I53 Manual de usuario
CommScope
CommScope 3X-C70B-3XR Manual de usuario
CommScope
CommScope Cell-Max CMAX-O-TCPUSEWI53 Manual de usuario
CommScope
CommScope ARGUS Manual de usuario
CommScope
CommScope CMAX-O-43 Series Manual de usuario
CommScope
CommScope ION-M8P S Manual de usuario
CommScope
CommScope CMAX Series Manual de usuario
CommScope
CommScope CMAX Series Manual de usuario
CommScope
CommScope CMAX-LHM2-30-I53 Manual de usuario
CommScope
CommScope CMAX-D-43-UW-i53 Manual de usuario
CommScope
CommScope F-042-GL-E Manual de usuario
CommScope
CommScope ValuLine VHLP3 Series Manual de usuario
CommScope
CommScope CMAX-OUS-43-i53 Manual de usuario
CommScope
CommScope CMAX-OMFX-43M-I53 Manual de usuario
CommScope
CommScope ASP7A Manual de usuario
CommScope
CommScope CMAX-DMF-43-UW-i53 Manual de usuario
CommScope
CommScope CMAX-DM20 Manual de usuario
CommScope
CommScope CMAX-DM CPUSE Series Manual de usuario
CommScope
CommScope 5NPX1006F Manual de usuario
CommScope
CommScope ValuLine VHLP1 Series Manual de usuario
Manuales populares de Antena de otras marcas
Alfa Network
Alfa Network APA-L01 Manual de usuario
Naval
Naval PR-422CA Manual de usuario
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario
TERK Technologies
TERK Technologies TV44 Manual de usuario
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Manual de usuario
HP
HP J8999A Manual de usuario
