Comm Net Systems V30/30 Manual de instrucciones

SETUP AND OPERATION MANUAL

FOR TELECOM BROADBAND

v30/30 Distribution Panel

Comm/net Systems, Inc.

4237 – 24th Avenue West

Seattle, WA 98199

TEL: 206.282.8670

FAX: 206.282.8684

www.commnetsystems.com

24/7 Sales & Service

To purchase Comm/net Systems solutions, contact your

Comm/net Systems representative at: (800) 274-0544

or e-mail: [email protected]

About Comm/net Systems

Comm/net Systems, Inc. (CSI) is the leader in high power density communications power

systems. Comm/net oﬀers comprehensive power and communications site systems integration

and deployment services via a national footprint of regional branch oﬃces. Additional

information can be found at www.commnetsystems.com.

net Systems logo are registered trademarks of Comm/net Systems, Inc. in the United States

and other countries. All other trademarks, service marks, registered marks, or registered

service marks are the property of their respective owners. Comm/net Systems assumes no

responsibility for any inaccuracies in this document. Comm/net Systems reserves the right to

change, modify, transfer, or otherwise revise this publication without notice.

Document Number: 048-781-30

Revision Level: r01

Published: July 2018

SETUP AND OPERATION MANUAL

FOR TELECOM BROADBAND

v30/30 Distribution Panel

V30/30 DISTRIBUTION PANEL

SETUP AND OPERATION MANUAL

ABOUT THIS MANUAL

About This Manual

To reduce the risk of damage to equipment, injury, or death; and to ensure proper

installation and operation of Comm/net Systems products, please be sure to read and

understand the entirety of this manual and any other supplied documentation. Keep

this document in a safe and accessible place for future reference.

Safety and Alert Symbols

The following symbols may appear in this manual, other supplied documentation, or on Comm/net Systems product labeling. The meaning of

this indication is explained below.

NOTICE

INDICATES IMPORTANT INFORMATION REGARDING THE COMPLETE AND PROPER FUNCTION OF A PRODUCT.

TYPICALLY REFERS TO MONITORING CONFIGURATION OR OTHER NONDANGEROUS SITUATIONS.

CAUTION

INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD DAMAGE

EQUIPMENT/PROPERTY OR COULD RESULT IN MINOR OR MODERATE INJURY.

WARNING

INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN INJURY OR DEATH.

DANGER

INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, WILL RESULT IN SERIOUS INJURY OR DEATH.

Product support

If you have any questions concerning Comm/net Systems products and services, contact our support staﬀ. Our knowledgeable support team

can provide product technical support and answer other questions regarding Comm/net products and services.

In addition to contacting Comm/net Support directly via phone or e-mail, our online help desk is available 24 hours a day, 7 days a week. The

help desk includes answers to commonly asked questions and self-help articles as well as an online ticket submission system if you need to

contact Comm/net after normal business hours.

yComm/net support is available by phone or e-mail Monday – Friday from 8am – 4:30pm Paciﬁc Standard Time.

yThe online web portal is available 24/7 to submit support requests and general questions, or view the FAQ and self-help articles.

NOTE: All questions submitted to the web portal will be answered during normal business hours.

yPhone: 1-800-274-0544

yE-mail: suppor[email protected]

yOnline Web Portal: https://commnetsystems.freshdesk.com

V30/30 DISTRIBUTION PANEL

SETUP AND OPERATION MANUAL

TABLE OF CONTENTS

Table of Contents

Section 1: Purpose and Applicability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 Product Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Section 2: Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Section 3: Unpacking and Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3.1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Section 4: Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1 Installation Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.1 Elevated Operating Ambient Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.2 Reduced Air Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.3 Mechanical Loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.4 Circuit Overloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.5 Reliable Earthing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.1.6 Disconnect Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

4.2 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4.3 Chassis Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4.4 Input Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4.5 Alarm Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.6 Installing The Network Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.7 Output Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.8 Breaker Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.9 Polarity Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.10 Display Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.11 Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Section 5: Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5.1.1 Firmware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5.1.2 Firmware Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5.2 Home Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.2.1 Bus Load and Voltage Displayed Per Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.2.2 Display Per Breaker Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.2.3 Alarm Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.3 Module Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5.3.1 Individual Breaker Load and Ampacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5.3.2 Breaker Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5.4 Bus Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.4.1 Bus Load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.4.2 Bus Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.5 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.5.1 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.5.2 Touch Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.5.3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.5.4 Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.6 Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.6.1 Raw Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.6.2 Conﬁguration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.6.3 Test Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.6.4 Restore Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

5.7 Review System Status via the Embedded Web Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.7.1 Default Static Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.7.2 Real-time Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5.7.3 Administration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Section 6: Product Speciﬁcations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Appendix A: Mechanical Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Appendix B: Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Appendix C: Supported Lugs for Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Appendix D: Supported Slimline Bullet Circuit Breakers. . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Appendix E: Output Cable Whips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Appendix F: One-Line Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

V30/30 DISTRIBUTION PANEL

SETUP AND OPERATION MANUAL

PAGE VI -

THIS PAGE INTENTIONALLY LEFT BLANK

V30/30 DISTRIBUTION PANEL

SETUP AND OPERATION MANUAL

PURPOSE AND APPLIcABILITy - PAGE 1

Section 1: Purpose and Applicability

The purpose of this document is to detail the installation and operation instructions

for the V30/30 distribution panel.

1.1 Product Model

This document applies to the following models of the

Comm/net Systems, Inc.® V30/30 distribution panel:

TABLE 1. V30/30 DISTRIBUTION PANEL MODEL

PART NUMBER DESCRIPTION

016-2121-10 V30/30 Distribution Panel

Section 2: Theory of Operation

2.1 Introduction

The V30/30 product family consists of a dual-input 30A/30B breaker position, 4RU

distribution panel with 40A connectorized outputs and an advanced touch screen

display. Breakers are available for this panel in ratings from 2 ampere up to 30 ampere.

2.2 Features

yModular design

y4RU; 19" or 23" rack compatible*

y2A and 2B inputs; 300A each

yUp to (60) breaker positions (30A/30B)

yUp to (6) distribution modules with (10) breaker positions each

yModules are dual input with (5) breaker positions per side (5/5); 150A

maximum current per module input

y35A maximum current per breaker position

yConnectorized outputs

yLCD touchscreen controller with Ethernet (HTTP; SNMP)

yOptional per-circuit current monitoring and RedundancyTracker™

yUnmatched safety and reliability

*23" rack ear kit required.

Figure 1. V30/30 Distribution Panel

V30/30 DISTRIBUTION PANEL

SETUP AND OPERATION MANUAL

PAGE 2 - PURPOSE AND APPLIcABILITy

THIS PAGE INTENTIONALLY LEFT BLANK

V30/30 DISTRIBUTION PANEL

SETUP AND OPERATION MANUAL

UNPAckING AND INSPEcTION - PAGE 3

Section 3: Unpacking and Inspection

The Comm/net Systems V30/30 distribution panel was carefully packaged at the

factory to withstand the normal rigors of shipping. However, you should carefully

inspect the box and contents to conﬁrm that no damage has occurred in transit. Most

shipping carriers require notiﬁcation of shipping damage within twenty-four hours of

delivery, and it is the responsibility of the recipient to inspect the shipment immediately

upon receipt.

3.1 Package Contents

Included with your product are the following items:

yV30/30 distribution panel

yBreaker module assemblies (up to 6 per panel)

yMounting hardware kit with necessary screws and washers

Section 4: Installation

4.1 Installation Preparation

When selecting an installation location, ensure that all of the following conditions are

met before proceeding.

4.1.1 Elevated Operating Ambient Temperature

If you install the panel in a closed or multi-unit rack assembly, the operating ambient

temperature of the rack environment may be greater than room ambient. Therefore,

take care to install the equipment in an environment compatible with the maximum

ambient temperature (TMA) speciﬁed in Section 6.

4.1.2 Reduced Air Flow

Installation of the equipment in a rack should be such that the amount of air ﬂow

required for safe operation of the equipment is not compromised.

4.1.3 Mechanical Loading

Mounting of the equipment in the rack should be such that a hazardous condition is

not achieved due to uneven mechanical loading.

4.1.4 Circuit Overloading

Give consideration to the connection of the equipment to the supply circuit and

the eﬀect that overloading of the circuits might have on overcurrent protection and

supply wiring. Use appropriate consideration for equipment nameplate ratings when

addressing this concern.

4.1.5 Reliable Earthing

Maintain reliable earthing of rack-mounted equipment. Pay particular attention to

supply connections other than direct connections to the branch circuit (e.g., use of power

strips).

4.1.6 Disconnect Device

A readily accessible disconnect device must be incorporated in the building

installation wiring.

V30/30 DISTRIBUTION PANEL

SETUP AND OPERATION MANUAL

PAGE 4 - INSTALLATION

4.2 Mounting

NOTICE

THIS PRODUCT MUST BE INSTALLED WITHIN A RESTRICTED

ACCESS LOCATION WHERE ACCESS IS THROUGH THE USE

OF A TOOL, LOCK AND KEY, OR OTHER MEANS OF SECURITY,

AND IS CONTROLLED BY THE AUTHORITY RESPONSIBLE

FOR THE LOCATION. THIS PRODUCT MUST BE INSTALLED

AND MAINTAINED ONLY BY QUALIFIED TECHNICIANS.

Step 1. Attach the (3) cable lacing bars to the threaded inserts found on the rear of the

chassis using the included 12-24 hardware (see Figure 2).

Step 2. Secure panel to equipment rack by tightening the included 12-24 hardware

into the mounting ears (see Figure 3).

4.3 Chassis Ground

CAUTION

DO NOT ENERGIZE THE PANEL BEFORE

CHASSIS GROUND IS CONNECTED.

The chassis ground is located in the side of the panel. A two hole lug landing position

is provided. See table below for termination information. A minimum of #6 AWG chassis

ground cable is required.

IMPORTANT: Grounding hardware not included. A properly-sized grounding

conductor must be installed per NEC (250.122).

TABLE 2. CHASSIS GROUND TERMINATION SPECIFICATIONS

TERMINATION

TYPE

HOLE/STUD

SIZE CENTER TO CENTER

RECOMMENDED TORQUE

VALUE

Threaded Insert 1/4 in. 5/8 in. 75 in∙lbs

Step 1. Secure the ground cable to the chassis by tightening 1/4 in. hardware (see

Figure 4).

Figure 3. Rack Install

Figure 2. Lacing Bars

Figure 4. Chassis Ground

Tabla de contenidos

Otros manuales de Automatización del hogar de Comm Net Systems

Comm Net Systems

Comm Net Systems Matrix 016-131-10 Manual de instrucciones

Manuales populares de Automatización del hogar de otras marcas

Truth Hardware

Truth Hardware Sentry II Manual de usuario

FIBARO

FIBARO FGWPA-111 Manual de usuario

Hezborg

Hezborg BGR8016B Manual de usuario

MYDLINK

MYDLINK Pro Series Manual de usuario

Panasonic

Panasonic KX-HNA101FX Manual de usuario

GamaBit

GamaBit Houseper Manual de usuario

nedis

nedis WIFILRF10C37 Manual de usuario

Veho

Veho TA45 Manual de usuario

Nexa

Nexa ZPR-111 Manual de usuario

Vimar

Vimar 00801 Manual de usuario

Leviton

Leviton 47604-F6 Manual de usuario

EVERSPRING

EVERSPRING AN180 Manual de usuario

Coltech

Coltech 18-1339 Manual de usuario

IDS

IDS NXT vegas Guía

Vimar

Vimar 03975 Manual de usuario

iNels

iNels RFIM-20B Manual de usuario

EVA Logik

EVA Logik ZW30 Manual de usuario

Leviton

Leviton ODCØP-S0W Manual de usuario

Comm Net Systems v30/30 Manual de instrucciones

Manuales populares de Automatización del hogar de otras marcas