ComfortSystem Bed Backrest Manual de instrucciones
ComfortSystem
ComfortSystem
COMFORTABLE Bed Backrest is easy to assemble on private
beds in the home environment. Bed backrest should be
placed on a sprung mattress in combination with a mattress.
COMFORTABEL Bed Backrest is designed to comply with
applicable parts of the bed standard EN 1970:1998 and is
designed for people older than 12 year.
– our experience is your guarantee
Instructions for users of
Bed Backrest
ComfortSystem – our experience is your guarantee
2 | COMFORTABEL - Bed Backrest
1.Assembly instructions
1.1 Scope of delivery
COMFORTABEL Bed Backrest is packed in a carton containing:
– Mechanics of bed backrest
– Motor
– Controll
– Transformer
– Fixing paper (accessories)
Total weight ca 12 kg
1.2 Unpacking
To facilitate the packing of the factory - the motor is in transport mode. It
means that the motor rear mount NOT is mounted on the bed backrest.
– Unpack the bed backrest from the carton and place it on the floor as
shown in Figure 1.
– Turn the motor 90 degrees and mount the L-shaped motor mount in
the engine’s rear mount. Use the enclosed motor bolt and secure it
with the so-called hairpin as shown in Figure 2. Assemble and then
screw the L-shaped bracket on the bacrest 4-edge pin.
Use the enclosed Star knob and disk, mount as shown in Figure 6
and 7.
Check that the motor house is poiting down as shown in
Figure 10.
Fixing paper (see separate installation
instructions)
!
ComfortSystem – our experience is your guarantee
COMFORTABEL - Bed Backrest | 3
1.3 Mounting on the bed
COMFORTABEL Bed Backrest can be mounted with the motor to the
right or to the left. If the motor, after unpacking, is on the right side -
continue the installation (as below). If the motor is placed on the wrong
side - go to part 5
– Place bed backrest centrally on the bed as shown in Figure 3.
– Bed backrest strap is placed around the bed as shown in Figure 4.
– Tighten the straps as tight as possible, as shown in Figure 5.
– Make sure the bed backrest is stable in the bed.
– Make sure that the straps are tightened.
Figure 1. Figure 2.
Figure 3. Figure 4. Figure 5.
!
!
ComfortSystem – our experience is your guarantee
4 | COMFORTABEL - Bed Backrest
1.4 Connecting the transformer and controller
– Make sure the controller is connected to the motor.
– Connect the cord to the wall socket.
NOTE! Flowchart. The transformer is mounted on the motor!
1.5 Adjustment to the right/left
The bad backrest motor can be placed on the right or the left side by
”turning around” the bad backrest as follows:
– Place the bed backrest on the floor as shown in Figure 1.
– Unscrew the knob on the rear motor mount as shown in Figure 6
and 7.
– Lift up and remove the rear motor mount as shown in Figure 7.
– Turn the bed backrest 360 degrees (the lined portion) as Figure 8.
– Rotate the motor 180 degrees so that the motor house is pointing
down as shown in Figure 9 and Figure 10. Make sure the motor, after
mounting, looks like Figure 10!
– Reposition the rear motor mount as shown in Figure 9.
– Screw the knob on the rear motor mount as shown in Figure 6 och 7.
ComfortSystem – our experience is your guarantee
COMFORTABEL - Bed Backrest | 5
Figure 1. Figure 6.
Figure 7. Figure 8.
Figure 9. Figure 10
ComfortSystem – our experience is your guarantee
6 | COMFORTABEL - Bed Backrest
2. Instructions for use
2.1 Power supply
The Bed backrest is driven by a low voltage motor (24V) and is powered
by a built-in transformer.
– The cord must be connected to the wall socket.
– Make sure the cord is not pinched or trapped in the bed
backrest
2.2 Regulation of bed backrest
Bed backrest is controlled by a hand control.
Buttons for UP and DOWN as outlined.
– Maximum load on the bed backrest = 70 kg. (Userweight ca 145 kg).
– Make sure the bed backrest has free space to fold up / forward.
– Make sure nothing is behind / under the bed backrest when it is folded
down / backwards.
3. Care instructions
COMFORTABEL Bed Backrest requires minimal maintenance.
Depending on the environment and use, maintenance can be required.
3.1 Normal cleaning
– Bed backrest cleaned with a damp cloth. Can be cleaned with readily
available cleansers and disinfectants.
– The backcloth can be washed at 60 degrees.
3.2 Lubrication
– Bed Backrest normally needs no lubrication. When necessary - the
backrest’s ramifications need lubrication.
3.3 Yearly oversight
– Make sure the power cord and cable to the controller are all right.
– Make sure the straps are all right.
!
!
ComfortSystem – our experience is your guarantee
COMFORTABEL - Bed Backrest | 7
4.Troubleshooting
A. The Bed Backrest doesn’t work at all
– Make sure the cord is connected to the wall socket.
– Make sure the hand control is connected to the motor.
– Make sure that the motor is connected to the transformer.
If the problem remains – contact the supplier.
B. Bed backrest work sometimes
– Make sure the hand control is properly connected to the motor.
– Make sure that the motor is connected to the transformer.
If the problem remains – contact the supplier.
Comfort System Scandinavia AB • Box 4034 • 561 04 Huskvarna
Tel 036-515 90 • Fax 036-500 01 • [email protected]
ComfortSystem
Our experience - your guarantee
Since its start in 1987, Comfort System has kept more or less the
same ownership and has operated under the same name – a fact
that is almost unique today in the branch. Our long experience
and knowledge of our product assortment, means that as a
customer you can feel secure in your choice of supplier.
– our experience is your guarantee
ComfortSystem – our experience is your guarantee
Tabla de contenidos
