ComfortHeat C 511T Manual de usuario
Programmable thermostat C 511T with
oor temperature sensor
C511T
Programmable thermostat C 511T with
oor temperature sensor EN
2
© 2019 Comfort Heat Ltd.
2
Thermostat C 511T has a CE marking which satisfies European
Council directives and applied standards EMC: EN 61000-6-1:
2001, EN 61000-6-3: 2001, LVD: EN 60730-1, EN 60730-2-9.
The product is a Class II device (enhanced insulation) and must be
connected to the following leads:
Term. 1: Neutral (N)
Term. 2: Live (L) 230 V±10%, 50/60 Hz
Term. 3 - 4: Load, max. 16A/ 3600W
Term. X: Do not connect
Term. 5-6: External floor sensor
1. THERMOSTAT USE INSTRUCTION
The programmable thermostat C 511T is specially developed to
provide comfort heating using as little energy as possible. C 511T
is used to control the floor heating but can equally be used with all
types of heating systems.
The thermostat C 511T can switch your heating system on at
pre-determined time on different days of the week. For each day
of the week you can set individual temperatures for 4 different
periods, called events. Lowering the temperature when the home
is unoccupied will reduce your energy costs without reducing
comfort.
The thermostat C 511T comes with a default factory schedule
3
4
suitable for most installations. The thermostat operates in
compliance with this default programme unless you set your
own weekly schedule. The thermostat has a reset button marked
R allowing you to reset the thermostat back to default factory
settings.
The thermostat C 511T features an adaptive function that
automatically changes the start time of heating periods so as to
ensure that the required temperature is reached at the set time.
After 3 days the adaptive function will have calculated when the
heating must be switched on.
2. FLOOR TEMPERATURE SENSOR INSTALLATION
Floor temperature sensor NTC is in protection class IP67 and
complies with applied standards EN 61386-1.
The temperature sensor is mounted in the oor as shown in Pic. 1.
The resistance of the oor temperature sensor is shown in Pic. 2.
Cut a groove in the oor and the wall to the thermostat junction
box. Put the sensor pipe into the groove and seal its end with
aluminium foil or a special metal cap to avoid the concrete
entering the pipe. Bend the pipe (10-16mm) between the wall and
the oor with a large bending radius (8 diameters). The end of the
5
pipe should be placed between the cable loops (under the heating
mat) but not closer than 30cm from the edge of heating area.
Insert the sensor into the pipe. This allows the sensor to be easily
replaced if necessary. The sensor cable can be extended by up to
50m by means of a separate cable. Connect the oor temperature
sensor to the thermostat as shown in the wiring diagram (Pic 4).
Picture 1 Picture 2
3. THERMOSTAT INSTALLATION
• Slide the power button down to OFF “0”.
• Release the front cover ONLY by inserting a small
screwdriver into the hole on either side of the thermostat
(Pic. 3). DO NOT open the thermostat by releasing the four
xing clips on the back.
• Make electrical connections according to the diagram (Pic.
4.)
• Mount the thermostat in the wall socket. Fit the frame and
carefully press the cover onto the thermostat. Ensure that
both the power slide button on the cover and the power
switch pin are down.
• Prepare thermostat for use.
6
Picture 3 Picture 4
4. FIRST TIME SETTINGS
The rst time the thermostat is connected, push the power slide
button to ON “I”. Language, time and date must be set. The menu
will automatically guide you through the process.
• Choose your language with the Up and Down buttons and
conrm with the OK button.
• Set the actual hour and press the OK button. Then set the
minutes. Press OK.
• Set the actual date: year, month and day. Conrm the
settings with the OK button.
The thermostat is now ready for use and will control your heating
according to the pre-programmed 4-event schedule, see chapter
7 (4- event settings).
5. GENERAL OPERATION
The power interrupter button allows you to turn the thermostat
ON “I” and OFF “0” by sliding the button up and down. When the
thermostat is switched o “0”, the relay disengages. All settings,
including time and date, will be remembered.
7
8
The thermostat is intuitively operated using the navigation
buttons. The function of each button is indicated above the button
on the display.
Back and Exit
In various parts of the menus and sub-menus you will nd the
Back and Exit items. Use Back to return to the last step. Use Exit to
return to initial display.
6. OPERATION MODES
The thermostat C 511T has 3 dierent modes of temperature
control:
9
Auto mode.
Select Auto if you want the temperature to be
controlled automatically via the 4-event schedule.
Manual mode.
Select Manual to cancel the programmed 4-event
schedule and to set the required temperature
manually. For example, during the holiday you may
want to adjust the temperature to 5°C for frost
protection while you are away. Press Manual, conrm
with OK and choose the required temperature.
Comfort mode.
Select Comfort to set a temporary comfort tempera-
ture for a single event. Press Comfort, conrm with OK
and choose the required temperature. Then enter the
required duration of comfort mode. After the set time
has elapsed, the thermostat will automatically revert to
Auto mode. Please note that Comfort mode is a tempo-
rary manual setting that will be automatically cancelled
by the next event in the programmed 4-event schedule.
7. THERMOSTAT SETUP MENU
4-event settings allow you to have the temperature controlled
10
automatically in accordance with a programme of your choice. You
can select temperature settings for 4 dierent events during the day:
When you wake up in the morning
When you away at work
When you come home
When you go to bed at night
The thermostat is pre-programmed with a 4-event schedule for easy
and economic heating control, see the chapter 8 (Factory settings). The
schedule can be easily changed in the following way:
1.Press the OK button to activate the 4-event
settings display.
2.Choose the days for which you want to
change the settings, Mon-Fri or Sat-Sun using
the up or down button. Press OK.
3.Choose one of 4-events, conrm with OK.
4.Now select the time and temperature for that
11
Otros manuales para C 511T
1
Tabla de contenidos
Idiomas:
Otros manuales de Termostato de ComfortHeat
ComfortHeat
ComfortHeat Comfort Touch Manual de usuario
ComfortHeat
ComfortHeat C 501 Manual de usuario
ComfortHeat
ComfortHeat C 511T Manual de usuario
ComfortHeat
ComfortHeat Comfort WiFi Manual de usuario
ComfortHeat
ComfortHeat Comfort ECO Manual de usuario
ComfortHeat
ComfortHeat Comfort Touch Manual de usuario
ComfortHeat
ComfortHeat MCD4 Manual de usuario
ComfortHeat
ComfortHeat MCC2-1991 Manual de usuario
ComfortHeat
ComfortHeat MCD5 -1999 Manual de usuario
ComfortHeat
ComfortHeat C 101 Manual de usuario
Manuales populares de Termostato de otras marcas
EWELLY
EWELLY EW-181 Manual de usuario
Prolon
Prolon T1100 Instrucciones de instalación
Computherm
Computherm Q20 Manual de usuario
Heatmiser
Heatmiser neoStat Manual de usuario
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario
