Comelit 1259C Manual de usuario

TECHNICAL

MANUAL

Module for SBTOP remote camera module

Art. 1259C Passion.Technology.Design.

Warning

Intended use

This Comelit product was designed for use in the creation of audio and video communication systems in residential,

commercial or industrial settings and in public buildings or buildings used by the public.

Installation

All activities connected to the installation of Comelit products must be carried out by qualiﬁed technical personnel, with

careful observation of the indications provided in the Manuals / Instruction sheets supplied with those products.

Wires

Cut o the power supply before carrying out any maintenance procedures.

Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system

manual.

We advise against running the system wires through the same duct as the power cables (230V or higher).

Safe usage

To ensure Comelit products are used safely:

• carefully observe the indications provided in the Manuals / Instruction sheets

• make sure the system created using Comelit products has not been tampered with / damaged.

Maintenance

Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance

with the indications provided in the Manuals / Instruction sheets.

Any repair work must be carried out

• for the products themselves, exclusively by Comelit Group S.p.A.,

• for systems, by qualiﬁed technical personnel.

Disclaimer

Comelit Group S.p.A. does not assume any responsibility for

• any usage other than the intended use

• non-observance of the indications and warnings contained in this Manual / Instruction sheet.

Comelit Group S.p.A. nonetheless reserves the right to change the information provided in this Manual / Instruction

sheet at any time and without prior notice.

Module that allows the cyclical management of the video signals from up to 3 cameras on a door entry monitor via a dedicated

key. Power supply: 12 V AC or 20 V DC. Can be used in SBTOP systems.

Description

1. Terminal block MR2 for system connection:

V1 S1 Coax input camera 1

V2 S2 Coax input camera 2

V3 S3 Coax input camera 3

IN A Camera module external control contact

GND Common contact

2. Programming microswitches S1

3. Terminal block MR1 for system connection:

L OUT L OUT BUS line output

L IN L IN BUS line input

~- ~+ 12 Vac 20 Vdc power supply input

Technical features

MAIN FEATURES

Product height (mm) 85

Product width (mm) 60

Product depth (mm) 35

Operating temperature (°C) -25 ÷ 40

DIN rail mounted Yes

DIN modules (no.) 4

Maximum current absorption (mA) 150

COMPATIBILITY

Simplebus Top audio/video system Ye s

AUDIO/VIDEO FEATURES

Audio/video system Yes

Connection

CAMERA CONTROL KEY

1259C 1200

12V~

230V~

V S

~ ~

LLL

OUT

IN IN

VIDEO ENTRY

SYSTEM RISER

VIDEO ENTRY

SYSTEM RISER

Requires separate power supply.

Operation and Programming

Art. 1259C can be used to manage analogue CCTV cameras (up to 3).

Art. 1259C can be used in systems with Art. 4888C in the SB1 section (running from the mixer power supply unit towards the

external units).

√With monitor on

fPress the programmed key to cycle through all connected cameras, in accordance with the diagram below. Sequential

switching can also be activated using a clean contact (C-NO) connected to the INA – GND input.

External

unit 3rd camera2nd camera1st camera

GENERIC OR CODED ACTUATOR MODE

MODE WITH AUDIO PORTER OR SWITCHBOARD

In this mode and with the door entry phone monitor switched on, it is possible to cycle through all the connected cameras by

repeatedly pressing the button programmed as “generic actuator”.

fMicroswitch “S1” must be set as illustrated below.

fSet the number of cameras connected using dip switches 7 and 8, as shown in the table below:

Default conﬁguration

Programming the number of cameras connected

1. Generic actuator mode

MODES DIP 1 DIP 2 DIP 3 DIP 4 DIP 5 DIP 6 DIP 7 DIP 8

Actuator coded to

address 5 (actuator code

on monitor 225) with 3

cameras connected

ON OFF ON OFF ON OFF ON ON

DIP 7 DIP 8

0 0

1 0

0 1

1 1

Before programming the module, see “5. Compatibility table for Art. 1259C”.

2. Coded actuator mode

3. Mode with external audio unit

Before programming the module, see “5. Compatibility table for Art. 1259C”.

In this mode and with the door entry phone monitor switched on, by repeatedly pressing the button programmed as “coded

actuator”, it is possible to cycle through ONLY the cameras connected to Art. 1259C with the corresponding address.

fTo activate the function, program the button on the monitor as coded actuator (with address between 220 and 227

inclusive) and set selector “S1” as illustrated in the table below:

Generic/coded actuator modes can also be used on a system which includes an audio-only external unit Art. 1622.

For operation with “audio only” external unit:

1. set DIP 1 of selector “S1” as illustrated below:

2. set the external unit to video mode as shown in the picture below:

12 3 456 7 8

ON DIP

In this mode, every time a call is received from the external unit or when self-ignition takes place, the monitor switches on and

displays the image from the ﬁrst camera connected to Art. 1259C. It will be possible to cycle through all cameras connected by

repeatedly pressing the programmed button.

Up to 8 modules Art. 1259C with 8 dierent codes can be installed in the same system.

Example for setting address on Art. 1259C for control by means of actuator code 224

S1 1259C address-coded actuator correspondence

DIP 1 DIP 2 DIP 3 DIP 4 DIP 5 DIP 6 Address 1259C Actuator code on monitor

1 0 0 0 0 0 0 220

1 0 1 0 0 0 1 221

1 0 0 1 0 0 2 222

1 0 1 1 0 0 3 223

1 0 0 0 1 0 4 224

1 0 1 0 1 0 5 225

1 0 0 1 1 0 6 226

1 0 1 1 1 0 7 227

4. Mode with switchboard 1998A -1998VC

5. Compatibility table for Art. 1259C with 1256 or other 1259C units

Generic/coded actuator modes can also be used on a system which includes Video calls from switchboard.

In this mode, every time a video call is made from the switchboard, the monitor switches on as soon as the handset is lifted (or

the audio button is pressed), and the image displayed will be the one from the ﬁrst camera connected to Art. 1259C.

At this point, each time a control button is pressed (see generic/coded actuator modes) or each time the manual contact is

closed (available by connecting the INA-GND contact to the OUT-OUT terminals of the switchboard), you will be able to cycle

through all available cameras.

fTo use this function, the remote camera module must be connected to the outgoing Bus line from terminals LM-LM of the

switchboard, and the switchboard set to “Video mode” before the call.

Generic actuator mode Coded actuator mode

Compatibility with 1256 No. 1256 units in generic actuator mode No. 1256 units in coded actuator mode

with codes between 220 and 227

Compatibility with Art. 1259C No other 1259C in generic actuator mode 1259C only in mode 2 with 8 separate

codes

System performance and layouts

For further information of system performance and to view installation layouts, click on the type of system that best meets your

needs :

• SBTOP audio/video system for the creation of audio-video systems for residential complexes.

www.comelitgroup.com

Via Don Arrigoni, 5 - 24020 Rovetta (BG) - Italy

6ª edizione 10/2018

cod. 2G40002083

CERTIFIED MANAGEMENT SYSTEMS

Tabla de contenidos

Otros manuales de Unidad de control de Comelit

Comelit

Comelit UT8020 Manual de usuario

Comelit

Comelit 1406 Manual de usuario

Comelit

Comelit SimpleHome 20046707 Manual de usuario

Comelit

Comelit 3335 Manual de instrucciones

Comelit

Comelit VEDOGSM Manual de usuario

Comelit

Comelit ARCHITECTUS-PRO ViP Manual de usuario

Comelit

Comelit UT1010 Manual del propietario

Comelit

Comelit K1406 Manual de usuario

Comelit

Comelit Ultra Manual de usuario

Comelit

Comelit FT/GEN/05 Manual de usuario

Comelit

Comelit UT2010 Manual de usuario

Comelit

Comelit 41ECN000 Manual de usuario

Comelit

Comelit Simplebus2 UT2010 Manual de usuario

Comelit

Comelit 3360B Manual de usuario

Comelit

Comelit 8273 Manual de usuario

Comelit

Comelit Simplebus2 Ultra UT2020 Manual de usuario

Comelit

Comelit Simplebus1 Ultra UT1020 Manual de usuario

Comelit

Comelit 1256 Manual de usuario

Comelit

Comelit Simplebus1 UT1020 Manual de usuario

Comelit

Comelit ONE/E Manual de usuario

Comelit

Comelit UT9331 Manual de usuario

Comelit

Comelit SK9001U Manual de usuario

Comelit

Comelit SK9000U Manual de usuario

Comelit

Comelit Ultra Simplebus2 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario