Colortrac SmartLF Ci24m Manual de usuario
CiIM Colortrac Ltd Page 1 of 8
Issue 1
Ci Instruction Manual
Date: 02/09/10
This is a confidential controlled document and is the property of Colortrac Ltd.
It is not to be copied or reproduced in part or whole. It is intended for staff to read.
S
Sm
ma
ar
rt
tL
LF
F
C
Ci
i
S
Sc
ca
an
nn
ne
er
rs
s
P
Pr
re
es
ss
s
P
Pa
ap
pe
er
r
B
Bl
lo
oc
ck
k
I
In
ns
st
tr
ru
uc
ct
ti
io
on
n
M
Ma
an
nu
ua
al
l
Ci Scanner Service Manual
Page 2 of 8
Ci Scanners
Ci24m, Ci24c & Ci24e
Ci40m, Ci40c & Ci40e
Press Paper Block Instruction Manual
Issue 1
©Colortrac Ltd 2010
•The product and the contents of this publication may be changed without prior notification.
•Colortrac Ltd makes every effort to ensure this publication is free from error. Misprints, errors
or quality observations should be reported to Technical Support, Colortrac Ltd.
•Colortrac Ltd shall not be liable for any damages, errors, issues or events that result from the
use of the equipment or this manual.
No part of this product or publication may be reproduced,
copied or transmitted in any form or by any means without
permission from:
Colortrac Ltd.
Units 3 – 5 Brunel Court.
Burrel Road.
St Ives,
Huntingdon,
Cambridgeshire,
PE27 3LW.
United Kingdom.
Tel: +44 (0)1480 464618
Fax: +44 (0)1480 464620
www.colortrac.com
Ci Scanner Service Manual
Page 3 of 8
1 PRESS PAPER BLOCK
1.1 Safety Precautions
•Ensure that the power is completely disconnected from the scanner unit.
•Ensure the scanner is positioned on its Colortrac stand, or a stable maintenance platform.
1.2 Tools
•Medium Pozi-drive screwdriver
•Medium Stubby Pozi-drive screwdriver
•Instant Adhesive
•Small Flat Screwdriver
1.3 Associated Part Numbers
•P003274 Press Paper Block
1.4 Procedure
1. Press down on the locking
buttons on both ends of the
scanner lid unit.
2. Open the lid unit right
back.
NOTE: Although the Press Paper Blocks can be stuck on without removing the Lid Cover Extrusion
Sub-A, it is recommended to remove it, so the Lid Cover Extrusion Sub-A can be laid flat, this prevents
the adhesive covered Press Paper Block from falling onto the CIS, which can damage the surface with
the adhesive.
To attempt to glue the Press Paper Block while the Lid Cover Extrusion Sub-A is still on is done so at
your own risk.
Ci Scanner Service Manual
Page 4 of 8
3. Under the Mylar strip,
remove the 4 x M4 Pan
Head Screws from the
elongated hole that screws
on the Lid Cover Extrusion
Sub-A. The second,
adjacent screw adjusts the
height of the lid (see
instructions 9 -11).*
NOTE: The Mylar strip should not be removed to get to the screws. While bending the Mylar back to
remove the screw, care is to be taken not to crease or damage the Mylar. Should it be creased or
damaged the Mylar strip should be replaced.
*Older scanners may not have the 2 sets of screws, and only have the M4 screws holding the lid on. However, removing the lid
is the same method.
4. Close the lid unit and
remove the 5 x M4 Pan
Head Screws from the
back of the Lid Cover
Extrusion Sub-A.
5. Remove the Lid Cover
Extrusion Sub-A and put
upside down onto a clean
work bench.
Ci Scanner Service Manual
Page 5 of 8
6. Clean up the area of the
missing Press Paper Block
with a screwdriver, to
remove any uneven
surfaces.
NOTE: If the block is still attached and
is being replaced because of damage,
use the screwdriver to break it off the
Lid Cover Extrusion Sub-A before
cleaning the surface.
7. Use an instant adhesive to
stick the block on, we
recommend Loctite 460, or
something similar that can
be found locally.
8. Apply a small amount of
the adhesive to the Lid
Cover Extrusion Sub-A in
the area that will occupy
the Press Paper Block
Ci Scanner Service Manual
Page 6 of 8
9. Position the Paper Press
Block on to the adhesive
and apply pressure for a
few seconds to bond the
Press Paper Block to the
Lid Cover Extrusion Sub-A.
Press Paper Blocks
10. Wipe off any excess
adhesive from around the
Press Paper Block using
an clean dry tissue, and
allow enough time for the
adhesive to dry fully.
11. After making sure the
Press Paper Block is
secure, refit the Lid Cover
Extrusion Sub-A on top of
the lid unit, and replace the
5 x M4 Pan Head screws.
Ci Scanner Service Manual
Page 7 of 8
12. Press the locking buttons
and open the lid unit.
13. Replace the 4 x M4 Pan
Head screws under the
Mylar strip. Being careful
not to damage the Mylar
strip as you feed the
screwdriver underneath it.
14. Close the lid unit. If the Lid
Cover Extrusion Sub-A
does not line up with the
end cover, open the lid unit
again and adjust the
second set of screws to
raise the lid cover.
Ci Scanner Service Manual
Page 8 of 8
15. To raise the Lid Cover
Extrusion Sub-A, loosen
the 4 x holding screws (in
the elongated holes). Then
tighten the adjust screw
next to it to push the lid
further away from the lid
unit. Tighten the holding
screws again to lock the lid
cover in place.
16. To lower the lid cover,
loosen the adjustment
screws, and tighten the
holding screws.
Otros manuales para SmartLF Ci24m
1
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Escáner de Colortrac
Colortrac
Colortrac SC Series Manual de usuario
Colortrac
Colortrac SmartLF Ci 40 Manual de usuario
Colortrac
Colortrac Flatbed 24120 Manual de usuario
Colortrac
Colortrac SmartLF SG Manual de usuario
Colortrac
Colortrac SmartLF SG Series Manual de usuario
Colortrac
Colortrac SmartLF Cx Series Manual de usuario
Colortrac
Colortrac UC56T Manual de usuario
Colortrac
Colortrac 5480e Manual de usuario
Colortrac
Colortrac Z Series Manual de usuario
Colortrac
Colortrac SmartLF Ci C24 MFP Manual de usuario
Colortrac
Colortrac SmartLFGx+ 28 Instrucciones de instalación
Colortrac
Colortrac SmartLF Gx 54 Manual
Colortrac
Colortrac SmartLF Cx40m Manual de usuario
Colortrac
Colortrac SmartLF Scan! 24 Manual de usuario
Colortrac
Colortrac 3 Series Manual de usuario
Colortrac
Colortrac T Series Manual de usuario
Colortrac
Colortrac SMARTLF SCAN Manual de usuario
Colortrac
Colortrac SmartLF Gx25m Manual de usuario
Colortrac
Colortrac SmartLF Cx 40M Manual de usuario
Colortrac
Colortrac SmartLF Ci 40 Manual de usuario
