Code Alarm PC 4400 Manual de usuario

Owner's Manual

Remote Vehicle Control System

IMPORTANT NOTE: The operation of the Power Code as described in this

manual is applicable to most vehicles. However, due to the engine type

and configuration of some vehicles (i.e. diesel engines), some functions

AND/OR SAFETY PRECAUTIONS may not apply.Please see your

installing dealer for more information.

PC 4400

Car Start,Security and

Convenience System

101454-7

Table of Contents

Features and Benefits of the PowerCode PC 4400TM ..................... 3

Using Your Remote Transmitter .............................................. 4

Arming the Security System

Pre-arm Mode

Disarming the Security System

Attempted Intrusion Identification

Disabling the IT-sTM InteriorTheft Sensor ............................... 5

Two-Stage Door Unlock

Activating the Trunk Release Feature

Turning on the Vehicle Headlights

Windows up/AUX 3

Windows down/AUX 4

Using the Car Finder Feature

Personal Protection Alarm (Panic)

Using Valet Mode

Automatic Convenience Options ............................................ 7

WhenYour Security System isTriggered ............................... 8

The Interior Status Indicator .................................................... 8

System Maintenance ................................................................ 8

Changing the Remote Control Battery

Adding Remote Controls to Your System

Deleting Lost or Stolen Remote Controls from Your System

BasicTroubleshooting ............................................................ 10

Emergency Disarm Procedure .......................................... 11

Emergency Disarm Button Location

Installer Programmed Options

Your Code-Systems, Inc. Limited Lifetime Warranty .......... 12

Code AlarmTheft Protection Plan ............................................13

Features and Benefits of the Power Code PC 4400

Two Easy-to-Use Weather-Resistant Remote Controls

The remote controls included with the Power Code PC 4400TM

utilize durable, moisture resistant cases and sealed rubber buttons

for reliability and long life. Rolling code technology prevents the

transmitter signals from being duplicated. The button functions are

clearly labeled to make the Power Code PC 4400TM simple to operate.

All Entrances Protected

Opening any door or entrance protected by the security system

triggers the alarm’s 125db siren (or vehicle horn) and flashes the

vehicle parking lights.

Starter Disable

The Power Code PC 4400TM protects your vehicle from theft by

disabling the starter when the system is armed.

IT-s

InteriorTheft Sensor

This patented sensor uses infra-red technology to reliably detect

vehicle impact associated with attempted intrusion. The IT-s sensor

guards against vehicle body damage, and theft of the vehicle’s

equipment (such as airbags) and personal belongings.

Remote Keyless Entry

The Power Code PC 4400TM conveniently locks and unlocks vehicle

doors and opens the trunk or hatch by remote control.*

Personal Protection Features

Remote Panic Alarm, Headlight Control, Illuminated Entry,

and Car Finder are among an array of features that enhance

personal safety.**May require additional componets and/or labor

Interior Status Indicator

The bright-red warning light is an effective visual deterrent to a

would-be thief.

TurboTimer

The Power Code PC 4400TM allows you to cool down your turbo

charged vehicle for 5 minutes after exiting.

PowerRange

Antenna

This long-range antenna allows you to operate the Power Code PC

4400TM from distances of up to 1/8mile.

E-Code Coded Override System

If this feature is enabled, it will allow you to enter a personal 4-digit

code that only you will know. This will be used for overriding the

system in the case of an emergency or a lost transmitter.

* If vehicle is equipped with power door locks and they are connected to the alarm system by your installer.

* Throughoutthis manual, ‘press’ refersto pressing

forless than 1 second;‘press and hold’ refers to

pressingfor more than 1second.

** ’Siren’ also refers to the vehicle horn if it is used as the alarm sounding device.*

†If you have chosen the Silent Arming Option, the siren will not sound when arming or disarming until the

appropriatebuttonis pressed a second time.

Press for Car Finder

Press and Hold for

Panic Alarm

Press and Hold for

Auxilary 2

Arming the Security System

To arm the system, exit the vehicle, close all doors, then press* the

ARM button. The siren** will “chirp” twice†and the parking lights will

flash twice, indicating the system is armed.The doors will also lock at

this time (if equipped and connected). The status indicator (red

warning light on the dash) will blink steadily, once per second.

Pre-arm Mode

If the siren chirps and the parking lights flash only once, this indicates

that the vehicle courtesy light is on, or that an entrance is not closed

securely. Check to see that doors, hood, and trunk are properly

closed. Once all entrances are secured (and the courtesy light is off),

the system will chirp / flash again.The system is now fully armed.

(If the entrance is not secured within 4 minutes, the system will arm

and ignore the unsecured entrance until it is closed.)

Disarming the Security System

To disarm the system, press the DISARM button.The siren will chirp

and the parking lights will flash once, and the doors will unlock. The

courtesy light will turn on for 1 minute, or until the vehicle is started.

Attempted Intrusion Identification

If the siren chirps four times when disarming, this indicates that the

system was triggered in your absence. The status indicator will also

flash rapidly. Perform the following operation to determine the protected

zone that triggered the system:

After disarming, press the

emergency override button.

The siren will chirp to indicate

the cause of the alarm trigger:

1 chirp IT-s Interior Theft Sensor

2 chirps Door

3 chirps Hood

4 chirps Trunk/Optional Sensors

5 chirps Ignition was turned on

Using Your Remote Transmitter

Press for two-car

operation (SHIFT)

Press and hold to activate

auxilary 4

Press to DISARM Security

System and Unlock Doors

Press TWICE for Two-Stage

Door Unlock*

PressandHoldtoOpenTrunk

Press to ARM,the

security system

Press and hold to

activate Auxilary 1

Press and hold to

actiavate auxilary 3

UsingYour Remote Transmitter

(cont.)

Disabling the IT-s InteriorTheft Sensor

It may be necessary at times to disable the IT-s Interior Theft Sensor,

especially when parking in areas (like parking garages) where

extreme vibration may cause false alarms. Press the ARM button and

then press the FIND/PANIC button within two seconds of pressing

ARM to disable the interior theft sensor.The siren will chirp three

times to indicate that the sensor is disabled. The sensor will become

enabled again the next time the system is armed normally.

Two-Stage Door Unlock

If this feature is enabled on your system, pressing DISARM one time

will unlock only the driver’s door. Press DISARM again within 1 minute

to unlock all doors.

Activating theTrunk Release Feature

Press and hold TRUNK to open the vehicle trunk or hatch (if equipped

and connected). If this button is used to operate another accessory,

the accessory will stay active for as long as the button is held.

Turning on theVehicle Headlights (Aux 1)

Press and hold the LIGHTS button to turn on the vehicle headlights.

(The alarm system will attempt to arm if not already armed, unless it is

in Valet Mode.) The lights will stay on for 20 seconds, or until LIGHTS

is pressed again.

UsingWindows Up/AUX 3

If this feature is enabled on your system, pressing WINDOWS UP for

one second will raise the vehicle windows.

UsingWindows/Down/AUX 4

If this feature is enabled on your system, pressing WINDOWS DOWN

for one second will lower the vehicle windows.

Using the Progressive Car Finder Feature

Press FIND on the remote control to locate your vehicle.The siren will

emit five short chirps at low volume, increasing in volume each of

three times the button is pressed.

Personal Protection Alarm (Panic)

Press and hold the PANIC button to activate the vehicle siren and

parking lights for 30 seconds. (If the vehicle horn is connected, the

horn will “pulse” for 30 seconds.) Press any remote control button to

turn off the Panic alarm.

Using Second Car Mode

If this feature is enabled, one transmitter will control two vehicles equipped

with a Power CodeTM system.To operate the second vehicle, press the

shift button, then within two seconds, press the desired function button.

UsingValet Mode

If the Passive Arming feature is enabled on your system, Valet mode

temporarily prevents the alarm system from arming automatically.

This is useful when fueling or servicing your vehicle.

To enterValet Mode:

With the vehicle ignition on, press the ARM button.The Green

dashboard warning light (status indicator) will turn on for one second,

then turn off.This indicates that the system is in Valet mode.Once the

ignition is turned off, the status indicator will emit a quick double-flash

pattern.

Note: In Valet mode, all keyless entry, convenience features operate

normally.

To exitValet Mode:

With the vehicle ignition on, press the DISARM button.The red

dashboard warning light (status indicator) will turn on for one second,

then turn off.This indicates that the system has exited Valet mode.

Automatic Convenience Options

The PowerCodeTM performs a variety of automatic functions to

enhance security and comfort. Some of these features are

programmable at the time of installation. Please see your installer for

further details.

Illuminated Entry

When the alarm system is disarmed, the vehicle courtesy lights will turn

on for 1 minute, or until the vehicle is started or the system is re-armed.

Illuminated Exit

When removing the key from the ignition, the vehicle courtesy lights

will turn on for 1 minute, or until the PowerCodeTM is armed.

Automatic Arming

The Power CodeTM will arm automatically 1 minute after the key is

removed from the ignition. This feature can be temporarily disabled by

placing the system into Valet mode.

Ignition Lock

If all doors are closed and the vehicle is started with the key, the doors

will automatically lock.

Ignition Unlock

When removing the key from the ignition, the doors will automatically unlock.

UsingYour Remote Transmitter (cont.)

UsingYour Remote Starter

(cont’d)

WhenYour Security System is Triggered

The PowerCode PC 4400TM will trigger if one of the following events

occurs while the system is armed:

• Any protected entrance is opened

• The vehicle ignition is turned on

• The vehicle is jolted hard enough to signal the impact detector

Once the alarm is triggered, the siren (or horn) sounds and the

vehicle parking lights flash for 30 seconds.The system will then re-

arm, awaiting the next intrusion attempt. To stop the siren while

keeping the alarm armed and doors locked, press the ARM button

while the system is triggered.

The Status Indicator is a high-intensity red light mounted in a visible

location on the vehicle dashboard. This red light gives a visual

indication of the alarm system’s state of operation. Note the chart

below:

If the Status Indicator is... ....then the Security System

Flashing Green is disarmed

Flashing Slowly is armed

Flashing Very Quickly was triggered in your absence

(see Attempted Intrusion ID - page 4)

Flashing Intermittently is in Valet mode(LED is GREEN)

(2 flashes, off, 2 flashes)

On (not flashing) is in Pre-arm mode

System Maintenance

Changing the Remote Control Battery

The two 3-v lithium batteries (CR2016) supplied in your remote

control should last approximately one year, depending on usage.

When the battery begins to weaken, you will notice a decrease in

range, or the distance from your vehicle that your remote transmitter

will operate. Follow the instructions below to change the remote

transmitter battery.

1.Insert the edge of a coin into the slot at the side of the remote

control.Twist the coin to pry the remote control halves apart.

2.Remove the old batteries and replace with new ones.

Be sure to observe the (+) and (-) signs in the battery compartment.

3.Carefully snap the case halves back together, then test the

remote control.

Adding Remote Controls toYour System

The PowerCodeTM has the ability to operate from up to eight (8)

remote controls. Follow these instructions to add a remote control to your

system.

1.Make sure the security system is disarmed and the ignition is off.

2.Open the driver’s door.

3.Turn vehicle ignition on.

4.Press and hold emergency override button.

After 15 seconds, the siren or horn will sound three (3) times.

This indicates that the unit has entered the remote control

programming mode.

5.Release the button.

6.Press the ARM button (button 1) on the remote control to be

programmed.

The siren or horn will sound once, indicating that the system

has “learned” that remote control.

7.Repeat step 6 for any additional remote controls.

8.Turn the vehicle ignition off to exit the programming mode.Test

all remote controls to ensure that they work properly.

Deleting Lost or Stolen Remote Controls fromYour System

If one of your remote controls is lost or stolen, follow these instructions

IMMEDIATELY to remove the control code from your system.

1. Have all remaining remote controls available.

2. Enter the control programming mode by following steps 1 - 5 of

Adding Remote Controls toYour System

(page 8).

3a.If you have only one remaining remote control, press the

ARM button on that remote control eight (8) times, pausing at

least 1 second between each press. Make sure that the siren

chirps each time you press the ARM button.

3b.If you have two remaining remote controls, press the ARM

button on each remote control four (4) times, pausing at

least 1 second between each press. Make sure that the siren

chirps each time you press the ARM button.

3c.If you have three remaining remote controls, press the ARM

button on the two remote controls three (3) times, then press

the ARM button on the remaining remote control twice. Pause

at least 1 second in between each press. Make sure that the

siren chirps each time you press the ARM button.

4. Turn the vehicle ignition off to exit the programming mode.

When you are finished, the lost or stolen remote control will no

longer operate your system.

Emergency Disarm Procedure

If your remote control is lost or fails to function, use this procedure to

disarm the PowerCode PC 4400TM and start your vehicle.

1.Use the keys to enter the vehicle.

The alarm will sound once the door is opened.

2.Insert the key into the ignition and turn to the ON position.

3.Locate and press the emergency override button.

The alarm will turn off and then you will be able to

start your vehicle.

Your Emergency Disarm Button is located:

Installer Programmed Options

Ignition On Door Lock ON OFF

Ignition Off Door Unlock ON OFF

Illuminated Entry/Exit ON OFF

Siren/Horn Chirps ON OFF

Passive Arming ON OFF

Pasive Door Locks ON OFF

Car start Run Time 12 min. 25 min.

Light/AUX1 Output Duration_____________________

Defrost/AUX2 Output Duration_____________________

Window Up/AUX3 Output Duration_____________________

Window Down/AUX4 Output Duration_____________________

System Maintenance

(cont.)

Basic Troubleshooting

This section outlines some of the basic issues you may experience

while becoming used to the PowerCode PC 7600TM. If you have a

problem that is not covered by this section, please consult your installer.

motpmySmotpmySmotpmySmotpmySmotpmyS melborPmelborPmelborPmelborPmelborP noituloSnoituloSnoituloSnoituloSnoituloS

seodlortnocetomeRkrowton

yrettabdaedrokaeW

tonlortnocetomeR demmargorp

yrettabegnahC

etomermargorP )8egap(lortnoc

mratonlliwmetsyS

rehtororooD neposiecnartne

nosithgilysetruoC

telaVnisimetsyS

edom

ecnartneesolC

ffothgilysetruocnruT

edomtelaVffonruT)6egap(

tratstonlliwmetsyS neposidooH

desserpsiekarB

doohesolC

ekarbesaeleR

Tabla de contenidos

Otros manuales de Arranque remoto de Code Alarm

Code Alarm

Code Alarm ca5154 professional Series Manual de usuario

Code Alarm

Code Alarm CA 5053 Manual de usuario

Code Alarm

Code Alarm ca5554 Professional series Manual de usuario

Code Alarm

Code Alarm Professional Series CA 5050 Manual de usuario

Code Alarm

Code Alarm CA 440SS Manual de usuario

Code Alarm

Code Alarm Professional Series CA 1050 Manual de usuario

Code Alarm

Code Alarm CA1BTW5 Manual de usuario

Code Alarm

Code Alarm CA 5051 Manual de usuario

Code Alarm

Code Alarm Professional Series CA6555 Manual de usuario

Code Alarm

Code Alarm CA 4051 Manual de usuario

Code Alarm

Code Alarm GUARDIAN CPL 100 Manual de usuario

Code Alarm

Code Alarm CA 411 Manual de usuario

Code Alarm

Code Alarm CA-500 Manual de usuario

Code Alarm

Code Alarm PC 4300 Manual de usuario

Code Alarm

Code Alarm ca6154 Professional Series Manual de usuario

Code Alarm

Code Alarm CA 2050 Manual de usuario

Code Alarm

Code Alarm PROFESSIONAL SERIES Manual de usuario

Code Alarm

Code Alarm ca 5152 Manual de usuario

Code Alarm

Code Alarm CSI-100 Manual de usuario

Code Alarm

Code Alarm ca6553 Manual de usuario

Code Alarm

Code Alarm SRT 9000 Manual de usuario

Code Alarm

Code Alarm CA-630 Manual de usuario

Code Alarm

Code Alarm PC 7500 Manual de usuario

Code Alarm

Code Alarm CA-535 Manual de usuario

Manuales populares de Arranque remoto de otras marcas

AstroStart

AstroStart 803U Manual de usuario

Durite

Durite 0-649-20 Manual

EINHELL

EINHELL BT-PS 1000 Manual

Linear

Linear ACCESS AK-21 Especificaciones técnicas

Soundstream

Soundstream TARANTULA RS.2 Manual de usuario

Jaycar Electronics

Jaycar Electronics MB3752 Manual de usuario

Ultra Start

Ultra Start 72 Series Manual de usuario

ADS

ADS FLASHLOGIC FLRSVW1 Manual de usuario

Selecta

Selecta JS012 Manual de usuario

Black Widow Security

Black Widow Security BW RAS 400 Manual de usuario

Vector

Vector Power City DK080706 Suplemento

Ozito

Ozito OJS-800 Manual de usuario

Profi-Partner

Profi-Partner 46387 Manual de usuario

EZ STARTER

EZ STARTER EZ-45 Manual de usuario

Viper

Viper 4204 Manual de usuario

Essex Electronics

Essex Electronics KE-1701 Manual de usuario

EINHELL

EINHELL EGS 3600 Manual

Rooboost

Rooboost RB-1750WP Manual de usuario