COBB Tuning AccessPORT Manual de usuario
User Guide
Mitsubishi Evo X
Mitsubishi Lancer Ralliart
(Select Models 2008+)
Pa e 2
Table of Contents
Product Introduction 4
Supported Vehicle List * 4
In-Box Contents 5
What Is A Map? 7
AccessPORT Installation 8
Pre-Installation 8
Gettin Started 9
Vehicle Identification 10
Map Selection 10
Save Stock ECU Pro ram Data 11
Install AccessPORT Pro rammin 11
Installation Complete 11
AccessPORT Features & Functionality 13
Monitor 13
Live Data 13
Data Lo 13
Set Rev Warnin 14
Set Live Data List 14
Set Data Lo List 14
Reset Live List 15
Reset Lo List 15
Performance 16
0-60 MPH 16
¼ Mile 16
Tune 17
Chan e Map 17
Show Current Map 17
Troubleshootin 18
Reset ECU 18
Read Codes 18
AccessPORT 19
About 19
Revision 1.094 Mar 8, 2012
Pa e 3
Settin s 19
Uninstall 19
AccessPORT Troubleshooting 0
AccessPORT will not communicate with vehicle. 20
AccessPORT cannot reflash ECU. 20
AccessPORT cannot identify vehicle durin installation. 20
Support Contact Information 20
Web 20
E-Mail 20
Phone 20
Environmental Information 1
Revision 1.094 Mar 8, 2012
Product Introduction Pa e 4
Product Introduction
Con ratulations on the purchase of the new AccessPORT handheld pro rammer. The
AccessPORT can:
●Repro ram the factory en ine control unit (ECU) with improved tunin parameters
throu h the on-board dia nostic (OBD-II) port
●Monitor vehicle sensor data usin on-screen analo or di ital au es
●Read and clear en ine dia nostic trouble codes (DTCs)
●Measure 0-60 and ¼ mile times
Supported Vehicle List *
●2008, 2010-2012 Mitsubishi USDM Evolution X (GSR, MR, and MRT)
●2008, 2010 Mitsubishi JDM Evolution X (RS, GSR, SST)
●2008-2010 Mitsubishi ADM/EDM Evolution X (GSR, MR)
●2009 Mitsubishi World Market Evolution X (GSR, MR)
●2009-2012 Mitsubishi Lancer Ralliart
** designed for and sold in North America only
* Not all models will be supported at initial release.
Revision 1.094 Mar 8, 2012
Product Introduction Pa e 5
In-Box Contents
AccessPORT Version
OR
AccessPORT Version b
Revision 1.094 Mar 8, 2012
Product Introduction Pa e 6
WARNING!
Installation and use of the AccessPORT may void all or a portion of
the vehicle manufacturer's standard warranty. There is no guarantee
expressed or implied by COBB Tuning or any of its affiliates for the
use of the AccessPORT. The user accepts all risks and
responsibilities when using the AccessPORT.
WARNING!
Use of the AccessPORT while operating a moving vehicle is strictly
prohibited by law. COBB Tuning and its affiliates accept no
responsibility for damages or injury caused by misuse of the
AccessPORT.
WARNING!
The AccessPORT may not be able to function if the vehicle's wiring
has been modified. If problems occur while using the AccessPORT,
please verify that all wiring to and from the ECU is correct and
functional.
Revision 1.094 Mar 8, 2012
Product Introduction Pa e 7
What Is A Map?
The AccessPORT repro rams the tunin parameters inside the factory en ine control unit
(ECU) usin map files, which contain specially written instructions for the AccessPORT to
follow durin the repro rammin process. A map file can contain information for any number
of different modifications or enhancements to a vehicle, ran in from a race map for a
heavily modified vehicle to an economy map for a stock vehicle. Throu h the use of the
AccessPORT and different map files the ECU can be repro rammed to accommodate
virtually any vehicle confi uration.
Revision 1.094 Mar 8, 2012
AccessPORT Installation Pa e 8
AccessPORT Installation
Pre-Installation
The AccessPORT comes with the most up-to-date software and map files available at the
time of shipment. However, it is possible that updated software and/or map files have been
made available since the time of shipment. Therefore, the recommended procedure is to
connect the AccessPORT to the AccessPORT Updater and AP Mana er software and
download the latest software and map files for the tar et vehicle. Please install the Software
CD for more information.
IMPORTANT!
Before installing the AccessPORT on the vehicle, it is important to verify that the
vehicle is adequately prepared for the installation process. Since the
AccessPORT uses the vehicle's battery for power and the ECU reprogramming
process requires adequate battery power as well, it is critical to verify that the
vehicle's battery has a good charge. This can be done through the use of a
battery charger/conditioner or by driving the vehicle for a period of time prior to
installation to allow the alternator to recharge the battery. Furthermore, please
ensure that all in-car electronic devices are turned off to reduce power draw on
the battery. This includes car stereos, video screens, GPS units, radar detectors,
interior and exterior vehicle lights, and any other electronic device that uses the
car battery for power.
Revision 1.094 Mar 8, 2012
AccessPORT Installation Pa e 9
Getting Started
1. Insert the key into the vehicle's i nition and leave it in the OFF position.
2. Locate the vehicle's OBD-II port under the left side of the driver's side dash.
3. Connect device to the OBD-II port.
a) (AccessPORT Version 2 only):
•Connect the small end of the provided USB
cable to the mini-USB port on the back of the
OBD connector.
•Plu the lar e end of the USB cable into the
standard USB port on the underside of your
AccessPORT. At this point the AccessPORT
will power up and after a few moments
present the installation menu.
•(EVO III and EVO IX only) Plu the
white sub-connector of the OBD
don le into the white connector
immediately to the left of the OBD-II
port under the dash. The white
connector must to be connected for
all operations.
Revision 1.094 Mar 8, 2012
AccessPORT Installation Pa e 10
b) (AccessPORT Version 2b only):
•Plu the OBD-II cable into the OBD-II port
under the dash.
•Connect the other end of the OBD-II cable
to the 10-pin port on the bottom of the
AccessPORT. At this point the
AccessPORT will power up and after a few
moments present the installation menu.
4. Plu the lar e end of the USB cable into the standard USB port on the underside of
your AccessPORT. At this point the AccessPORT will power up and present the
installation menu after approximately 20-30 seconds.
5. Select [Install] from the AccessPORT menu by pressin the [OK] button to proceed
with installation. The i nition key must be in the ON position. Below is a dia ram of
the AccessPORT's keypad function.
Revision 1.094 Mar 8, 2012
Otros manuales para AccessPORT
2
Tabla de contenidos
Otros manuales de Accesorios para automóviles de COBB Tuning
